Large-scale depositional characteristics of the Ulleung Basin and its impact on electrical resistivity and Archie-parameters for gas hydrate saturation estimates

Michael Riedel; Timothy S. Collett; H.-S. Kim; J.-J. Bahk; J.-H. Kim; B.-J. Ryu; G.-Y. Kim

doi:10.1016/j.marpetgeo.2013.03.014

Home/Archive/USGS

USGS · 70093197

Large-scale depositional characteristics of the Ulleung Basin and its impact on electrical resistivity and Archie-parameters for gas hydrate saturation estimates

Michael Riedel·Timothy S. Collett·H.-S. Kim·J.-J. Bahk·J.-H. Kim·B.-J. Ryu·G.-Y. Kim

View original source ↗Export metadata ↓

Abstract

Gas hydrate saturation estimates were obtained from an Archie-analysis of the Logging-While-Drilling (LWD) electrical resistivity logs under consideration of the regional geological framework of sediment deposition in the Ulleung Basin, East Sea, of Korea. Porosity was determined from the LWD bulk density log and core-derived values of grain density. In situ measurements of pore-fluid salinity as well as formation temperature define a background trend for pore-fluid resistivity at each drill site. The LWD data were used to define sets of empirical Archie-constants for different depth-intervals of the logged borehole at all sites drilled during the second Ulleung Basin Gas Hydrate Drilling Expedition (UBGH2). A clustering of data with distinctly different trend-lines is evident in the cross-plot of porosity and formation factor for all sites drilled during UBGH2. The reason for the clustering is related to the difference between hemipelagic sediments (mostly covering the top ∼100 mbsf) and mass-transport deposits (MTD) and/or the occurrence of biogenic opal. For sites located in the north-eastern portion of the Ulleung Basin a set of individual Archie-parameters for a shallow depth interval (hemipelagic) and a deeper MTD zone was achieved. The deeper zone shows typically higher resistivities for the same range of porosities seen in the upper zone, reflecting a shift in sediment properties. The presence of large amounts of biogenic opal (up to and often over 50% as defined by XRD data) was especially observed at Sites UBGH2-2_1 and UBGH2-2_2 (as well as UBGH1-9 from a previous drilling expedition in 2007). The boundary between these two zones can also easily be identified in gamma-ray logs, which also show unusually low readings in the opal-rich interval. Only by incorporating different Archie-parameters for the different zones a reasonable estimate of gas hydrate saturation was achieved that also matches results from other techniques such as pore-fluid freshening, velocity-based calculations, and pressure-core degassing experiments. Seismically, individual boundaries between zones were determined using a grid of regional 2D seismic data. Zoning from the Archie-analysis for sites in the south-western portion of the Ulleung Basin was also observed, but at these sites it is linked to individually stacked MTDs only and does not reflect a mineralogical occurrence of biogenic opal or hemipelagic sedimentation. The individual MTD events represent differently compacted material often associated with a strong decrease in porosity (and increase in density), warranting a separate set of empirical Archie-parameters.

Explore related subjects

Marine and Petroleum Geology Article

Source-reported bounding extent: 35° to 38° latitude; 129° to 133° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Michael Riedel, Timothy S. Collett, H.-S. Kim, J.-J. Bahk, J.-H. Kim, B.-J. Ryu, G.-Y. Kim. 2013. Large-scale depositional characteristics of the Ulleung Basin and its impact on electrical resistivity and Archie-parameters for gas hydrate saturation estimates. https://doi.org/10.1016/j.marpetgeo.2013.03.014

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2025

Terrebonne Basin, Gulf of Mexico gas hydrate resource evaluation and 3-D modeling of basin-scale sedimentation, salt tectonics, and hydrate system evolution since the early Miocene

In assessing methane hydrate as a potential transitional energy source, quantification of in-place volumes of gas is a first step—and yet, global, regional, and even local estimates of gas volumes contained within hydrate are highly variable, including within the extensively-studied Gulf of Mexico (GoM) gas hydrate province. Here, we construct the first 3-D basin and hydrocarbon system model of the Terrebonne Basin (Walker Ridge protraction area, northern GoM) to estimate in-place resources contained as gas within hydrate, as well as to provide the first estimate of in-place resources contained within free gas accumulations in the basin. The resultant model-predicted 3-D distributions (and saturations) of hydrate are consistent with independent seismic interpretation and borehole observations. This study reveals both sedimentation-driven and salt diapir-driven gas hydrate recycling produce elevated hydrate saturations in the basin (“recycling” occurs when relative upward shifts of the gas hydrate stability zone (GHSZ) cause hydrate dissociation, generating buoyant free gas that may reaccumulate as higher-saturation hydrate at the new base of GHSZ). An important finding of this study (particularly given that, globally, the source of methane in marine hydrate systems tends to be poorly understood) is that microbial sources can explain most or all hydrate occurrences in Terrebonne Basin. We calculate that ∼32 × 10 9 m 3 (∼1.1 10 12 ft 3 ) of methane gas is trapped within hydrate accumulations throughout Terrebonne Basin, while nearly 2 × 10 9 m 3 (∼67 × 10 9 ft 3 ) of methane occurs as free gas at high saturations within sandy reservoirs beneath the GHSZ and ∼35 × 10 9 m 3 (∼1.2 × 10 12 ft 3 ) occurs as free gas at low saturations within muddy units beneath the GHSZ. In total, our calibrated 3-D model predicts that nearly 70 × 10 9 m 3 (∼2.5 × 10 12 ft 3 ) of microbial methane is trapped as gas hydrate and free gas in the Terrebonne Basin.

Marine and Petroleum Geology↗

USGS2024

Mapping the resistivity structure of Walker Ridge 313 in the Gulf of Mexico using the marine CSEM method

A marine controlled source electromagnetic (CSEM) campaign was carried out in the Gulf of Mexico to further develop marine electromagnetic techniques in order to aid the detection and mapping of gas hydrate deposits. Marine CSEM methods are used to obtain an electrical resistivity structure of the subsurface which can indicate the type of substance filling the pore space, such as gas hydrates which are more resistive. Results from the Walker Ridge 313 study (WR 313) are presented in this paper and compared with the Gulf of Mexico Gas Hydrate Joint Industry Project II (JIP2) logging while drilling (LWD) results and available seismic data. The hydrate, known to exist within sheeted sand deposits, is mapped as a resistive region in the two dimensional (2D) CSEM inversion models. This is consistent with the JIP2 LWD resistivity results. CSEM inversions that use seismic horizons provide more realistic results compared to the unconstrained inversions by providing sharp boundaries and architectural control on the location of the resistive and conductive regions in the CSEM model. The seismic horizons include: 1) the base of the gas hydrate stability zone (BGHSZ), 2) the top of salt, and 3) the top and bottom of a fine grained marine mud interval with near vertical hydrate filled fractures, to constrain the CSEM inversion model. The top of salt provides improved location for brines, water saturated salt, and resistive salt. Inversions of the CSEM data map the occurrence of a ‘halo’ of conductive brines above salt. The use of the BGHSZ as a constraint on the inversion helps distinguish between free gas and gas hydrate as well as gas hydrate and water saturated sediments.

Louisiana↗

USGS2024

Comparison of measured versus modeled TOC in the Tuscaloosa marine shale of Southwestern Mississippi, U.S.A.

This study presents a comparison of measured versus modeled total organic carbon (TOC) in the Upper Cretaceous Tuscaloosa marine shale (TMS) of southwestern Mississippi as a case study to evaluate the effects of mineralogy on the TOC estimated from the ΔlogR method. The ΔlogR method is utilized to calculate TOC, which involves baselining sonic transit time and resistivity log curves in a non-source rock section of the formation. In our application, the well log curves were baselined in the upper TMS, which is described as a non-source rock section, and in the lower TMS above the high resistivity zone (HRZ), which is described as having a higher carbonate content. The ΔlogR calculated TOC values from these two baselining approaches show that the lower baseline results in improved agreement between measured TOC and calculated TOC. This improvement is likely to be due to the lower baseline accounting for the increase in resistivity caused by higher carbonate content, in addition to any presence of TOC. The upper baseline, which has a lower carbonate content, does not account for this resistivity increase. Additionally, sample type appears to affect the comparison of measured and ΔlogR calculated TOC. Most of the samples used in this study are legacy cuttings that were not preserved during storage, exposing the high surface area cuttings to increased rates of oxidation, whereas geophysical logs record the rock properties in situ. To account for this oxidation effect, the difference between the medians of the TMS HRZ TOC core and cuttings values was added to each TOC measurement in this study, resulting in a median measured TOC value that is similar to the median of the lower TMS-baselined ΔlogR calculated TOC value. Overall, this study demonstrates that carbonate content and sample type can affect how well measured and ΔlogR-modeled TOC values compare.

Mississippi↗