Geology Reports⌕ Search
Home/Archive/USGS

USGS · 70030875

Characteristics of fly ashes from full-scale coal-fired power plants and their relationship to mercury adsorption

Y. Lu·M. Rostam-Abadi·R. Chang·C. Richardson·J. Paradis
View original source ↗Export metadata ↓

Abstract

Nine fly ash samples were collected from the particulate collection devices (baghouse or electrostatic precipitator) of four full-scale pulverized coal (PC) utility boilers burning eastern bituminous coals (EB-PC ashes) and three cyclone utility boilers burning either Powder River Basin (PRB) coals or PRB blends,(PRB-CYC ashes). As-received fly ash samples were mechanically sieved to obtain six size fractions. Unburned carbon (UBC) content, mercury content, and Brunauer-Emmett-Teller (BET)-N2 surface areas of as-received fly ashes and their size fractions were measured. In addition, UBC particles were examined by scanning electron microscopy, high-resolution transmission microscopy, and thermogravimetry to obtain information on their surface morphology, structure, and oxidation reactivity. It was found that the UBC particles contained amorphous carbon, ribbon-shaped graphitic carbon, and highly ordered graphite structures. The mercury contents of the UBCs (Hg/UBC, in ppm) in raw ash samples were comparable to those of the UBC-enriched samples, indicating that mercury was mainly adsorbed on the UBC in fly ash. The UBC content decreased with a decreasing particle size range for all nine ashes. There was no correlation between the mercury and UBC contents of different size fractions of as-received ashes. The mercury content of the UBCs in each size fraction, however, generally increased with a decreasing particle size for the nine ashes. The mercury contents and surface areas of the UBCs in the PRB-CYC ashes were about 8 and 3 times higher than UBCs in the EB-PC ashes, respectively. It appeared that both the particle size and surface area of UBC could contribute to mercury capture. The particle size of the UBC in PRB-CYC ash and thus the external mass transfer was found to be the major factor impacting the mercury adsorption. Both the particle size and surface reactivity of the UBC in EB-PC ash, which generally had a lower carbon oxidation reactivity than the PRB-PC ashes, appeared to be important for the mercury adsorption. ?? 2007 American Chemical Society.

Explore related subjects

Energy and FuelsArticle

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Y. Lu, M. Rostam-Abadi, R. Chang, C. Richardson, J. Paradis. 2007-06-22. Characteristics of fly ashes from full-scale coal-fired power plants and their relationship to mercury adsorption. https://doi.org/10.1021/ef070145s

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2024

3-D geological modeling for numerical flow simulation studies of gas hydrate reservoirs at the Kuparuk State 7-11-12 Pad in the Prudhoe Bay Unit on the Alaska North Slope

Accurate reservoir evaluation requires reliable three-dimensional (3-D) geological models. This study conducted 3-D geological modeling for numerical flow simulation of the B1 sand gas hydrate reservoir at the Kuparuk State 7-11-12 pad, Prudhoe Bay Unit, Alaska North Slope. The model integrates well logs, core, and seismic data to address spatial heterogeneity in geological structures and reservoir properties. Two modeling types were performed: structural framework modeling and petrophysical property modeling. For structural framework modeling, seismic data and well log markers were used to reproduce subsurface structures characterized by a normal fault system. A volume-based modeling algorithm and stair-step gridding were applied. The resulting 3-D model comprised 2,640,000 grid cells across 264 layers, including seven fault grids. For petrophysical property modeling, total porosity was initially modeled using sequential Gaussian simulation with collocated cokriging. To reproduce the upward coarsening of the B1 sand, upscaled log-derived total porosity and a 3-D trend depicting total porosity variation were used as primary and secondary data, respectively. Gas hydrate saturation distribution was modeled similarly, with secondary data from estimated porosity distribution and seismic-derived acoustic impedance map enhancing accuracy. Results indicate higher gas hydrate saturation in the upper part of the B1 sand and areas with higher acoustic impedance. Intrinsic permeability was modeled from the total porosity and clay-bound water volume, and effective permeability was derived from the gas hydrate saturation and intrinsic permeability distributions based on the “Tokyo model”. Effective permeability distributions were influenced by the total porosity, gas hydrate saturation, and intrinsic permeability. Within the same layer, higher gas hydrate saturation leads to decreased effective permeability. In total, 100 sets of multiple scenarios were prepared, providing input data for dynamic flow simulations to evaluate the effects of lateral heterogeneity in reservoir properties and the hydraulic characteristics of faults on production behavior for preassessment before the long-term production test.

Alaska↗
USGS2020

Nanoscale molecular composition of solid bitumen from the Eagle Ford Group across a natural thermal maturity gradient

Microscopic solid bitumen is a petrographically defined secondary organic matter residue produced during petroleum generation and subsequent oil transformation. The presence of solid bitumen impacts many reservoir properties including porosity, permeability, and hydrocarbon generation and storage, among others. Furthermore, solid bitumen reflectance is an important parameter for assessing the thermal maturity of formations with little to no vitrinite. While the molecular composition of solid bitumen will strongly impact associated parameters such as the development of organic matter porosity, hydrocarbon generation, and optical reflectance, assessing the molecular composition of solid bitumen in situ within shale reservoirs can be challenging due to the small grain sizes (often ≤1 μm in diameter) and the inherent heterogeneity of shale formations. Here we employ the recently developed atomic force microscopy based infrared spectroscopy (AFM-IR) technique to investigate solid bitumen molecular composition in situ within shale samples from the Late Cretaceous Eagle Ford Group. These samples possess sulfur-rich type II kerogens that span a natural thermal maturity gradient from early oil generation to the dry gas window. The application of AFM-IR allows for the rapid collection of thousands of compositional measurements from solid bitumen with ∼50 nm resolution. Our results indicate that (i) solid bitumen from the lower Eagle Ford displays both intra- and intergranular variation in the relative abundance of CH 2 , C═C, and C═O moieties present; (ii) this molecular variation tends to, but does not always, decrease with an increase in thermal maturity; and (iii) the solid bitumen composition between samples, from an atomic ratio perspective, is more similar than analysis of bulk kerogen isolates would indicate. These findings are discussed with perspective toward understanding the impact of thermal stress on the composition of secondary organic matter within the Eagle Ford Shale and highlight the growing awareness that organic matter heterogeneity within petroliferous mudrocks extends down to the nanoscale regime.

Energy and Fuels↗
USGS2019

Nanoscale molecular fractionation of organic matter within unconventional petroleum source beds

Fractionation of petroleum during migration through sedimentary rock matrices has been observed across lengths of meters to kilometers. Selective adsorption of specific chemical moieties at mineral surfaces and/or the phase behavior of petroleum during pressure changes typically are invoked to explain this behavior. Such phenomena are of interest as they impact both the quality and recoverability of petroleum resources. Given the current emphasis on unconventional (continuous) resources, there is a need to understand petroleum fractionation occurring during expulsion and migration at the nanometer to micron scale, due to the fine-grained nature of petroliferous mudrocks. Here, organic matter compositional differences observed within kukersites (petroleum source beds containing acritarch Gloeocapsomorpha prisca) and the overlying carbonate reservoir layer from the Ordovician Stonewall Formation are explored using a suite of spectroscopic methods, primarily through atomic force microscopy based infrared spectroscopy (AFM-IR). AFM-IR is capable of providing spatial resolutions approaching 50 nm and allows for assessment of the molecular fingerprint of kukersite organic matter across transition zones from organic-rich ‘source’ layers into neighboring carbonate ‘reservoir’ layers ~150 μm away. Results indicate that organic matter composition begins to vary immediately following expulsion from source layers, with loss of carbonyl groups and a concomitant decrease in alkyl chain-length, as migration distance increases. These chemical transitions correlate with a decrease in fluorescence intensity, increase in solid bitumen reflectance, and increase in Raman aromaticity proxies (D-G band separation) in the organic matter. Our findings are consistent with the retention of polar compounds onto mineral grains during expulsion and migration, following primary cracking and bituminization of the Gloeocapsomorpha prisca kerogen.

Energy and Fuels↗