An underwater instrument for determining bearing capacity of shallow marine sediments

Ronald C. Circe

doi:10.1520/gtj10516j

Home/Archive/USGS

USGS · 70012942

An underwater instrument for determining bearing capacity of shallow marine sediments

Ronald C. Circe

View original source ↗Export metadata ↓

Abstract

A small, portable, underwater instrument for measuring carbonate substrate bearing capacity in situ is described. The device was used in various shallow water (< 9 m) carbonate reef environments. Criteria for design and operation were based on ability to deliver controlled levels of stress to bearing plates of various sizes, operability underwater by scuba divers, transportability, and cost.

Explore related subjects

Geotechnical Testing Journal Article

Keep this discovery

Explore connections, maps & timelines

BibTeX RIS

Ronald C. Circe. 1985. An underwater instrument for determining bearing capacity of shallow marine sediments. https://doi.org/10.1520/gtj10516j

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

USGS2026

Design and functionality analysis of the high-stress permeameter (HSP), a device developed for measuring mechanical and hydraulic properties of gas hydrate-bearing pressure core

To characterize sediment compressibility and permeability in the presence of gas hydrate, a naturally occurring combination of water and methane that requires elevated pressure and reduced temperature to remain stable, a high-stress permeameter (HSP) device was developed. The HSP was designed to accept gas hydrate-bearing pressure core specimens in their plastic liner at pressures of 10–11 MPa. The HSP was further designed to carry out compressibility and permeability tests over a range of effective stresses while maintaining the requirements for gas hydrate stability. To verify the validity of HSP measurements of sediment consolidation properties, we tested remolded kaolin samples in the HSP and three standard fixed-ring oedometers. Furthermore, we compared the direct fluid-flow permeability measurements from the HSP with estimates based on Terzaghi’s log-time method for calculating permeability from 1-dimensional oedometer-style consolidation tests. We found agreement between all devices for consolidation (e.g., coefficients of compressibility and recompression) and permeability results. These findings indicate the suitability of the HSP for consolidation tests, as well as the log-time method for estimating permeability from oedometer consolidation tests.

Geotechnical Testing Journal↗

USGS2000

Evaluation and application of the transient-pulse technique for determining the hydraulic properties of low permeability rocks: Part 2: Experimental application

In Part 1 of this study, the general solution to the transient-pulse test (Hsieh et al. 1981) was extended to evaluate quantitatively the transient variations in hydraulic head and the corresponding distributions of hydraulic gradient within a test specimen. In addition, the conditions and the validity of using the expression proposed by Brace et al. (1968) to compute the low permeability of a rock specimen from a transient-pulse test were examined. Some theoretical considerations related to the optimal design of a transient-pulse test were also discussed. Part 2 presents a relatively general and convenient approach for determining not only the hydraulic conductivity and specific storage of a specimen directly from a transient-pulse test, but also the compressive storage of the fluid reservoirs. The accuracy and efficiency of this method are demonstrated through (1) the comparison of the compressibility of the fluid-reservoir (permeating) system back-calculated from the transient-pulse tests with the value obtained from calibration tests, and (2) its application to a series of experimental studies designed to investigate the effects of confining pressure on the hydraulic properties of Shirahama sandstone and Inada granite, two rock types available widely in Japan.

Geotechnical Testing Journal↗

USGS1998

Theoretical Evaluation of the Transient Response of Constant Head and Constant Flow-Rate Permeability Tests

A theoretical analysis is presented that compares the response characteristics of the constant head and the constant flowrate (flow pump) laboratory techniques for quantifying the hydraulic properties of geologic materials having permeabilities less than 10-10 m/s. Rigorous analytical solutions that describe the transient distributions of hydraulic gradient within a specimen are developed, and equations are derived for each method. Expressions simulating the inflow and outflow rates across the specimen boundaries during a constant-head permeability test are also presented. These solutions illustrate the advantages and disadvantages of each method, including insights into measurement accuracy and the validity of using Darcy's law under certain conditions. The resulting observations offer practical considerations in the selection of an appropriate laboratory test method for the reliable measurement of permeability in low-permeability geologic materials.

Geotechnical Testing Journal↗