Geology ReportsSearch

USGS · 70011989

Contemporary doming of the Adirondack Mountains: Further evidence from releveling

Abstract

The Adirondack Mountains constitute an anomalously large, domical uplift on the Appalachian foreland. The dome has a NNE—SSW axis about 190 km long, and an east—west dimension of about 140 km. It has a structural relief of at least 1600 m, and a local topographic relief of up to 1200 m. First-order leveling in 1955, and again in 1973 along a north—south line at the eastern margin of the Adirondack shows an uplift rate of 2.2 mm/yr at the latitude of the center of the dome and a subsidence rate of 2.8 mm/yr at the northern end of the line near the Canadian border. The net amount of arching along this releveled line is 9 cm ± 2 cm (Isachsen, 1975). To test the idea that this arching represented an “edge effect” of contemporary doming of the Adirondacks as a whole, the National Geodetic Survey was encouraged to relevel a 1931 north—south line between Utica and Fort Covington (near the Canadian border) which crosses the center of the dome. The releveling showed that the mountain mass is undergoing contemporary domical uplift at a rate which reaches 3.7 mm/yr near the center of the dome (compare with 1 mm/yr for the Swiss Alps). Three other releveled lines in the area support this conclusion.

Explore related subjects

90° N90° S · 180° W ← longitude → 180° E
Source-reported bounding extent: 43.04799214874441° to 44.89509467289085° latitude; -75.68357029846126° to -73.31377725183206° longitude. This indicates report coverage, not an exact sampling location. View area on OpenStreetMap.

Keep this discovery

Explore connections, maps & timelines

BibTeXRIS

Y.W. Isachsen. 1981. Contemporary doming of the Adirondack Mountains: Further evidence from releveling. https://doi.org/10.1016/0040-1951(81)90051-2

Cite the original work for its findings. Save a collection to share your selection of sources.

KEEP EXPLORING

Related USGS reports

GST-1: A high-resolution global sediment thickness model

Global Sediment Thickness 1 (GST-1) is a high-resolution sedimentary thickness model calculated on a 0.125° x 0.125° grid. It modifies the sediment thickness of the 1° x 1° Earth Crustal Model 1 (ECM1) by means of 3D inversions of free air gravity anomalies. GST-1 is calculated by performing structural inversions on high-density contrasts across two crustal boundaries: the sediment – basement interface and the crystalline crust – upper mantle interface. The inversions are calculated in each of ten overlapping 3D models that span the globe. These ten models are merged to obtain the GST-1 global model, providing an eight-fold increase in lateral spatial resolution in comparison with ECM1 and CRUST 1.0. Our sediment thickness model exploits the nearly continuous sampling of gravity data when compared to the irregular, sparse sampling of seismic refraction data. Sediment thickness values in GST-1 are in excellent agreement with independently derived cross sections from well-studied sedimentary basins, and within expected resolution limits of seismic refraction data. GST-1 offers a robust, high resolution global model of sedimentary thickness to support studies of sedimentary basins.

Tectonophysics

Fairweather transform boundary Oligocene to present orogenesis: Fairweather Range vertical extrusion and rotation of the Yakutat microplate at ca. 3 Ma

Oblique-slip along transform fault boundaries is often partitioned between a strike-slip system and thrust faults that accommodate contraction. However, topography along the Yakutat-North American transform (Fairweather fault), is asymmetric with low-terrain above active thrusts on the western, Yakutat side of the transform and high topography on the continental side with peaks >4500 m (Mount Fairweather: 4671 m) to the west of the Border Ranges fault, limited recorded earthquakes >M4, and no apparent reverse faults to generate the highest terrain. In this study we compile, for the first time, published U-Pb zircon, 40 Ar/ 39 Ar and K-Ar (hornblende, muscovite, and biotite) and U-Th/He and fission-track (zircon and apatite) bedrock ages (109) from 75 samples to investigate the exhumation history of the Fairweather Range region, complemented by a published detrital sample (ZFT and AFT) and 13 new 40 Ar/ 39 Ar (hornblende, biotite, and K-feldspar) ages on 9 bedrock samples from both sides of the Fairweather fault. Additionally, we examined published seismicity and geodetic data of the Fairweather region and assessed if plate paleo-vectors correlate with the cooling history of the Fairweather Range. Cooling age, seismic, and block-motion patterns indicate the Fairweather Range has been vertically extruded between the Fairweather and the Border Ranges faults as a coherent block since ca. 25 Ma. The pre-6 Ma Pacific plate motion (N30°W) aligns with the N33°W strike of the Fairweather Fault whereas a hypothetical pre-6 Ma Yakutat microplate paleo-vector of (N39°W) does not: indicating a post-6 Ma timing for Yakutat microplate counter-clockwise rotation (9°). We infer that rotation and impingement of the Yakutat microplate along the Fairweather fault at ca. 3 Ma led to the development of the Fairweather restraining bend and increased cooling rates. The resultant thickened Fairweather welt and the ∼30 km thick southeast end of the Yakutat microplate compounded double-indenter tectonics into Alaska's southeast convergent corner

Tectonophysics

A scaling relationship for the width of secondary deformation around strike-slip faults

Simple mechanical arguments suggest that slip along interlocked, rough faults, damages surrounding rocks. The same arguments require that the scale of secondary damage is proportional to the size of geometric irregularities along the main fault. This relationship could apply at all scales, but has, so far, been difficult to observe at the 10s to 100 s of km scales of large, natural faults, often because large-scale deformation is distributed across wide, complex plate-boundary fault systems, like the San Andreas Fault. The geometry and geology of another large-scale plate-boundary strike slip fault—the Queen Charlotte Fault (QCF)—is, in contrast, especially simple. Here, we show that observations of secondary deformation are well-aligned with predictions of stress variations caused by geometric irregularities along the QCF, suggesting a geometric relationship between primary fault geometry and secondary deformation. The analytic stress solution reveals that the highest stresses and highest likelihood of failure are confined to a zone of influence (ZOI) with a width quantified by ZOI = λ / 2 π "> ZOI=λ/2π , where λ is the wavelength of geometric variations along the main fault. This simple model is consistent with ∼100-km-scale observations along the QCF and can theoretically be used to predict the width of secondary deformation at all scales.

Queen Charlotte Fault