Geology Reports⌕ Search

Geology topics

Research about United States

Source-linked reports with geographic coverage including United States.

1,087 records · Page 59Linked to original sources
USGS1986

Water-quality appraisal of NASQAN stations below impoundments, eastern Tennessee

The National Stream Quality Accounting Network (NASQAN) is a network of stations at which systematic and continuing water-quality data are collected. Major objectives of this U.S. Geological Survey program are (1) to depict areal variability of streamflow and water-quality conditions nationwide on a year-by-year basis and (2) to detect long-term changes in streamflow and stream quality. Several NASQAN stations in East Tennessee are downstream from impoundments which have a significant effect on water quality. NASQAN data obtained from the Tennessee River below Watts Bar Dam and the Clinch River below Melton Hill Dam were compared to water-quality data from the basins upstream. The comparison indicates that NASQAN data obtained below impoundment may not be adequate to describe a composite picture of water quality in the accounting unit. Detention time of storage in the impoundments is believed to moderate the range of constituent values observed at the NASQAN stations. Data obtained upstream and downstream from Watts Bar Dam indicate that the water sampled at the NASQAN station comes from stratified layers of the impoundment and is not representative of an integrated sample of water from the impoundment. Values of total recoverable iron suggest that, because of adsorption to sediments in impoundments, some constituents are not accurately described by sampling below impoundments. Relations between water-quality constituents and flow at stations on the Clinch River and Tennessee River are not well defined due to regulation. Direct load computations for many constituents were therefore not possible, which diminished the utility of data from these NASQAN stations to account for quantity versus quality of the water. Load computations were only possible for ionic constituents through use of a continuous specific-conductance record as an intermediary. Compensation for the effects of discharge prior to application of the Seasonal Kendall test for trends could not be done and identification of trends in water-quality constituents caused by some process (source) change was not possible. Some water-quality trends indicated by data from the Clinch and Tennessee Rivers might reflect the decreasing trend in discharge during the 1972-82 water years. Thus the stations below Watts Bar Dam and below Melton Hill Dam do not adequately meet the NASQAN objective to detect and assess long-term changes in stream quality.

Tennessee↗
USGS1986

Regionalization of low-flow characteristics of Tennessee streams

Procedures for estimating 3-day 2-year, 3-day 10-year, 3-day 20-year, and 7-day 10-year low flows at ungaged stream sites in Tennessee are based on surface geology and drainage area size. One set of equations applies to west Tennessee streams, and another set applies to central and east Tennessee streams. The equations do not apply to streams where flow is significantly altered by activities of man. Standard errors of estimate of equations for west Tennessee are 24 to 32% and for central and east Tennessee 31 to 35%. Streamflow recession indexes, in days/log cycle, are used to account for effects of geology of the drainage basin on low flow of streams. The indexes in Tennessee range from 32 days/log cycle for clay and shale to 350 days/log cycle for gravel and sand, indicating different aquifer characteristics of the geologic units that sustain streamflows during periods of no surface runoff. Streamflow recession rate depends primarily on transmissivity and storage characteristics of the aquifers, and the average distance from stream channels to basin divides. Geology and drainage basin size are the most significant variables affecting low flow in Tennessee streams according to regression analyses. (Author 's abstract)

Tennessee↗
USGS1986

Potential for leakage among principal aquifers in the Memphis area, Tennessee

The principal aquifers in the Memphis area consist primarily of sand or sand and gravel, and the confining beds consist of clay, silt, sand, and lignite. The Jackson Formation and upper part of the Claiborne Group serve as the confining bed separating the water table aquifers from the Memphis Sand; the Flour Island Formation separates the Memphis Sand from the Fort Pillow Sand. Differences in total hydraulic head among the principal aquifers in the Memphis urban area result in vertical hydraulic gradients which create a potential for inter-aquifer exchange of water. Throughout this area, the gradient is downward from the water table aquifers to the Memphis Sand. In the central part of the Memphis urban area, the vertical hydraulic gradient is upward from the Fort Pillow Sand to the Memphis Sand, and in the eastern and western parts, it is downward from the Memphis Sand to the Fort Pillow Sand. The vertical distribution of carbon-14 data for water from the fluvial deposits, Memphis Sand, and Fort Pillow Sand shows an increase in the relative age of the water with depth. The areal distribution of carbon-14 data for water from the upper part of the Memphis Sand indicates that relatively recent water has been brought into the major cone of depression in the potentiometric surface of the Memphis Sand, either by horizontal movement or from downward vertical leakage. The normal, near-surface geothermal gradient in the Memphis area was determined to be 0.6 C/100 ft. Deviations from the normal geothermal gradient, in areas affected by intense pumping from the Memphis Sand, indicate that downward vertical leakage occurs from the water table aquifers through the Jackson-upper Claiborne confining bed to the Memphis Sand. The velocity of downward vertical leakage of water from the Memphis Sand through the Flour Island confining bed to the Fort Pillow Sand was determined to be 0.0066 ft/day by analysis of borehole temperature data from an observation well in the northeastern part of the Memphis area. From this velocity and the head difference between the Memphis Sand and the Fort Pillow Sand at this locality, the hydraulic conductivity of the Flour Island confining bed was determined to be 0.00114 ft/day. (Lantz-PTT)

Tennessee↗
USGS1985

Low flows and flow duration of Tennessee streams through 1981

Estimates of low-flow characteristics and flow duration for the period of record at continuous-record streamflow gages are essential in hydrologic studies and water-resources management. This report provides estimates of low flow for 1, 3, 7, 14, 30, 60, and 90 consecutive days for recurrence intervals of 2, 5, 10, and 20 years for continuous-record streamflow gages. These estimates were used in correlation methods to estimate low flow at partial-record streamflow sites for 1, 3, and 7 consecutive days for a recurrence interval of 10 years; and 3 consecutive days for a recurrence interval of 20 years.

Tennessee↗
USGS1984

Techniques for estimating magnitude and frequency of floods on streams in Indiana

Equations are presented for estimating the magnitude and frequency of floods at ungaged sites on unregulated and nonurban streams in Indiana. The equations were developed by multiple-regression, analysis of basin characteristics and peak-flow statistical data from 242 gaged locations in Indiana, Ohio, and Illinois. The State of Indiana was divided into seven areas on the basis of the regression analysis. A set of equations for estimating peak discharges with recurrence intervals of 2, IO, 25, 50, and 100 years was developed for each area. Significant basin characteristics in the equations are drainage area, channel length, channel slope, mean annual precipitation, storage, precipitation intensity, and a runoff coefficient. Standard errors of estimate for the equations range from 24 to 45 percent. Methods are also presented for estimating flood magnitude and frequency at sites on gaged streams. Flood-frequency data based on observed peaks are given for 270 gaged locations. Twenty of these are on regulated streams, and six are on urban streams. Basin characteristics are also included car 245 of the gaged locations on unregulated and nonurban streams. No techniques are given for estimating flood magnitude and frequency at ungaged sites on regulated or urban streams. A rainfall-runoff model was tlsed to synthesize long-term peak data at 11 gaged locations on small streams. Flood-frequency curves developed from the long-term synthetic data were combined with curves based on short-term observed data to provide weighted estimates of flood magnitude and frequency at the rainfall-runoff stations.

Indiana↗
USGS1983

Use of digital land-cover data from the Landsat satellite in estimating streamflow characteristics in the Cumberland Plateau of Tennessee

Characteristics of Streamflow at ungaged sites in coal-mining areas of the Cumberland Plateau may be estimated with regression equations that relate streamflow characteristics to the physiographic and climatic characteristics of the corresponding drainage basins. An experiment was performed to compare the accuracy of equations using basin characteristics derived from maps and climatological records (control group equations) with the accuracy of equations using basin characteristics derived from digital processing of Landsat spectral data as well as maps and climatological records (experimental group equations). Results of this experiment show that (with the exception of low flows and four of six annual peak logarithms) drainage area can explain more than 90 percent of the variance in all streamflow characteristics in both groups of equations. Seventeen of 39 experimental group equations that have two basin characteristics each are different from the corresponding control group equations. Five of the 17 differing experimental group equations have no counterpart in the control group because of lack of significance in control group basin characteristics, seven are slightly more accurate, and five are not measurably different in accuracy. When the equations in both groups are arranged into six flow categories, there is no substantial difference in accuracy between equations using basin characteristics derived from maps and climatological records (control group) and equations using basin characteristics derived from Landsat tapes as well as maps and climatological records (experimental group) for this particular study area, the Cumberland Plateau of Tennessee.

Tennessee↗
USGS1983

Technique for estimating depth of floods in Tennessee

Estimates of flood depths are needed for design of roadways across flood plains and for other types of construction along streams. Equations for estimating flood depths in Tennessee were derived using data for 150 gaging stations. The equations are based on drainage basin size and can be used to estimate depths of the 10-year and 100-year floods for four hydrologic areas. A method also was developed for estimating depth of floods having recurrence intervals between 10 and 100 years. Standard errors range from 22 to 30 percent for the 10-year depth equations and from 23 to 30 percent for the 100-year depth equations.

Tennessee↗
USGS1983

Base flow and ground water in upper Sweetwater Valley, Tennessee

The upper Sweetwater Valley area has a flow system with complex interaction between surface and ground water. A water budget study indicated that during dry years approximately three-fourths of the annual flow to Sweetwater Creek may be derived from ground-water sources. Hydrograph analysis showed seasonal variation of recharge to the ground-water flow system. Streamflow records were analyzed to estimate the frequency of low flow of Sweetwater Creek at river mile 16.7, and indicated the lowest average flow for 1 day in 20 years to be about 5.1 cubic feet per second. Two periods of base-flow measurements of Sweetwater Creek identified channel reaches with significant gains and losses of streamflow. Base flow measurements also showed interbasin transfer of water among sub-basins of the valley. Major flow surpluses were associated with areas in which the majority of flow originated at a spring. Topographically low areas adjacent to the main stem of Sweetwater Creek generally have surplus flow. Topographically higher areas generally have deficient surface outflow unless significant spring flow occurs in the basin. Ground-water recharge occurs by water draining into sinkholes, faults, and fractures. Ground-water flow is regionally diffused across formation strikes from the topographically low areas unless the water is exposed to highly permeable formations or impervious formations. Ground water infiltrates the highly permeable formations and flows along strike. Ground water encountering impervious formations may discharge at small springs at the contact, or may reroute along the contact if the upgradient rock is sufficiently permeable or has well developed secondary porosity. Groundwater discharges to streams at innumerable seeps and at a few large springs. Areas of ground-water flow up-gradient of large springs are hypothesized as likely areas of significant ground-water reservoirs.

Tennessee↗
USGS1977

Acid-rain weathering of a metasedimentary rock basin, Herkimer County, New York

A geochemical balance of major chemical constituents of precipitation inflow with those of surface-water outflow was used to evaluate the effect of acid rainfall (average pH = 4.3) on weathering rates of metasedimentary rocks underlying a surface-water basin in New York State. Precipitation samples and surface-water samples show that approximately 45 percent of the net cation outflow is due to weathering by precipitation acidity. The remaining 55 percent of the cation load in the outflow is attributed to interactions between atmosphere, rock, and soil water in the unsaturated zone. Comparison of the acidity of acid precipitation and air-equilibrated distilled water suggests that since preindustrial time, precipitation acidity has probably increased weathering rates for this basin approximately 75 percent. The increased acidity of the precipitation may also increase the rate of dissolution of heavy metals from water-piping systems.

New York↗
USGS1977

Leachate plumes in ground water from Babylon and Islip landfills, Long Island, New York

Landfills operated by the Towns of Babylon and Islip in southwest and central Suffolk County contain urban refuse, incinerated garbage, and scavenger (cesspool) waste; some industrial refuse is deposited at the Babylon site. The Islip landfill was started in 1933, the Babylon landfill in 1947. The landfills are in contact with and discharge leachate into the highly permeable upper glacial aquifer (hydraulic conducitvity 190 to 500 ft/d [feet per day]). The aquifer is 74 feet thick at the Babylon landfill and 170 feet thick at the Islip landfill. The leachate-enriched water occupies the entire thickness of the aquifer beneath both landfills, but hydrologic boundaries retard downward migration of the plumes to deeper aquifers. The Babylon plume is 1,900 feet wide at the landfill and narrows to about 700 feet near its terminus 10,000 feet from the landfill. The Islip plume is 1,400 feet wide at the landfill and narrows to 500 feet near its terminus 5,000 feet from the landfill. Hydrochemical maps and sections show the distribution of the major chemical constituents of the plumes. The most highly leachate-enriched ground water obtained was from the Babylon site; it contained 860 mg/L (milligrams per liter) sodium, 110 mg/L potassium, 565 mg/L calcium, 100 mg/L magnesium, 2,700 mg/L bicarbonate, and 1,300 mg/L chloride. Sulfate was notably absent or in low concentration in most parts of both plumes. Nitrogen in plume water was mostly in the form NH4+, and concentrations as high as 90 mg/L were found; concentrations of nitrogen as N in the plume were less than 10 mg/L. As much as 440 mg/L iron and 190 mg/L manganese were found in the leachate-enriched water. Samples were also tested for arsenic, boron, cadmium, cobalt, chromium, copper, mercury, nickel, lead, selenium, strontium, and zinc. Boron was more or less ubiquitous and was found in concentrations as high as 2 mg/L. Organic carbon was found in concentrations as high as 2,250 mg/L in the most highly leachate-enriched water but attenuated rapidly to less than 20 mg/L. Dissolved-solids concentrations near the landfills were between 400 and 3,000 mg/L at Babylon and between 500 and 1,500 mg/L at Islip. Ground-water temperatures near the landfills exceed those in ambient water by as much as 7°C at Babylon and 16°C at Islip. Heat contributed by the landfills was mostly dissipated within 0.4 mi of the landfill, butat Islip, the warm leachate-enriched water extended 0.5 mi downgradient. The entrance of leachate into the less dense ground water as pulsations after rainfall may explain the presence of high leachate enrichment near the bottom of the aquifer. A comparison of the physical characteristics of leachate-enriched ground water with those of ambient water suggests that the downward movement of leachate results from its greater density. Simulation of the movement and dispersion of the Babylon plume with a mathematical dispersion model indicated the coefficient of longitudinal dispersion to be about 60 ft 2 /d (feet squared per day) and the ground-water velocity to be 1 ft/d. However, the velocity determined from the hydraulic gradient and public-supply wells in the area was 4 ft/d, which would cause a plume four times as long as that predicted by the mathmatical dispersion model. At the Islip site, the plume was one-third the length calculated on the basis of the age of the landfill. The shortness of the plumes has not been explained; it may be a result of the leachate's having been too dilute to form a plume during the early years of the landfills.

New York↗
USGS1977

Summary of results from electromagnetic and galvanic soundings on Kilauea Iki lava lake, Hawaii

The purpose of this report is to summarize various electrical sounding studies made on the Kilauea Iki lava lake and to present some of the preliminary interpretations that resulted from the measurements. The following discussion is not intended as a complete interpretation, but is intended to summarize the major points made in an invited oral presentation at the American Geophysical Union fall meeting held in San Francisco, Calif. on December 6, 1976. This paper was part of a group of papers dealing with various geophysical studies recently made on the Kilauea Iki lava lake. A general plan map of Kilauea Iki lava lake is shown in figure 1. Electromagnetic (EM) loop-loop soundings, D.C. resistivity soundings, and VLF apparent resistivity measurements were made on the lave lake surface. All of these surveys were made to determine the geoelectric structure of the lava lake and to determine parameters of the molten basaltic lens that exist in the partially solidified lava lake.

Hawaii↗
USGS1977

Exploratory water well, St. George Island, Florida

A 1,026-foot well was drilled into the Floridan aquifer on St. George Island in search of a supply of water for residential development in 1971. This is the only well on the island on record to have been drilled below 200 feet for water. The well was abandoned; water flowing from the well was saline. It had a specific conductance of 7,500 micromhos per centimeter at 25° Celsius. The specific conductances of samples taken at drilling depths 217-1,026 feet ranged from 3,140 to 39,600, with the maximum value at 470 ft. A composite geophysical and lithologic log of the well shows spontaneous potential, single-point resistance, gamma-ray, neutron, gamma-gamma, and caliper logs. Well-site notes, a written description of cuttings samples, a graph showing the relation of specific conductance of water samples to the depth of the well at time of sampling, and four chemical analyses of the water are included in the report.

Florida↗
USGS1976

Solute transport and modeling of water quality in a small stream

An injection of chloride, sodium, and stable strontium was made at a constant rate for 3 hours into Uvas Creek, Santa Clara County, Calif., to determine the mass transport processes in a small stream. Five observation points were selected within a 610-metre reach of the stream below the injection site. Water samples were collected at the observation points during and immediately after the injection. A mathematical model of the stream was obtained by solving analytically and optimally the one-dimensional mass transport equation of the solutes in the stream. Comparison of field results with a simplified mathematical model indicates the dominance of convection in the behavior of sodium and chloride. The concentration of chloride and sodium can be closely simulated by the model. However, strontium cannot be well represented by the simplified model, which contains a first-order decay-type sink.

California↗
USGS1976

Heat-flow data from southeastern Oregon

With the exception of values from two holes drilled within 2 km of Mickey Hot Springs, 17 new heat-flow values in southeastern Oregon are within or somewhat below the range one would normally expect in non-anomalous parts of the North American Cordillera. This is not surprising for a region in which most igneous rocks on the surface are 5 m.y. old or more. There is a suggestion of a thermal anomaly associated with the very young (late Pleistocene or Holocene) Diamond Craters lava field, and the thermal regime on both sides of Steens Mountain seems to be controlled, to some degree, by lateral and vertical movement of water.

Oregon↗
USGS1976

Transport and dispersion of fluorescent tracer particles for the dune-bed condition, Atrisco Feeder Canal near Bernalillo, New Mexico

A tracer technique in which mineral particles were coated with fluorescent dyes was used to study the rates of transport and dispersion of sediment particles`of various diameters and specific gravities for a dune-bed condition in an alluvial channel. The experiment was conducted in the Atrisco Feeder Canal near Bernalillo, N. Mex., between May 1 and July 14, 1967. A continuous point source of tracers, approximated by injections at 5- or 10-minute intervals, was maintained for 7 days so that the steady-dilution procedure could be used to calculate the transport rate of bed material. After termination of the injection process, the spatial-integration procedure was used to follow the movement of the tracers downstream and to calculate the transport rate. Samples of the bed material in transport and the accompanying tracers moving along the surface of the dune bed were obtained periodically throughout the study with the "dustpan" sampler especially designed for fluorescent tracer studies. In addition, the spatial distributions of the tracers in the dune bed were determined three times during the study by core sampling.

New Mexico↗
USGS1976

Results of phytoplankton sampling at National Stream Quality Accounting Network stations in Montana, 1975 water year

Twelve National Stream Quality Accounting Network stations were operated in Montana during the 1975 water year. The network was established for the purpose of acquiring a base of hydrologic data for use by agencies engaged in water-resources planning on a national or regional scale. Among the characteristics analyzed were phytoplankton identification and cell counts. Samples consisted of composites of equal aliquots, collected at the center of each quartile of flow, using modified suspended-sediment samplers and sediment collection techniques. Identification and counting were done using the Sedgwick-Rafter cell method. Cell counts ranged from 21 cells per millilitre at Flathead River at Flathead, British Columbia to 27,000 cells per millilitre at Yellowstone River near Sidney. The class Bacillariophyceae was most abundant in both number and variety at all sampling sites. Anabaena and Aphanizomenon of the phyllum Cyanophyta were found at six stations and two stations respectively. These two genera of blue-green algae often become abundant in enriched waters resulting in nuisance conditions.

Montana↗