Geology ReportsSearch

Geology topics

Research about United States

Source-linked reports with geographic coverage including United States.

1,087 records · Page 19Linked to original sources

Reconnaissance of potential alternate water supply sources for the City of Gary, West Virginia

Seven potential sources of water, consisting of free-flowing discharge from abandoned coal mines at six locations and one abandoned flooded underground coal mine air shaft, were sampled for chemical analysis to assess the quality of the groundwater emanating from the seven mine sources. The six free-flowing mine discharge sources were also assessed for discharge by current-meter measurements on two separate occasions. The U.S. Geological Survey assessed these seven sources to provide information to the City of Gary, West Virginia (W. Va.), and the City of Gary’s consulting engineer with groundwater-quality and flow data to allow them to assess the seven sites as potential alternate sources of water for the City of Gary to augment its existing supply. For the six sites where discharge could be measured, discharge ranged from a minimum of 0.082 cubic feet per second (ft 3 /s) to a maximum of 3.685 ft 3 /s. Of the six sites measured, only two, Harmon Branch at Thorpe, W. Va. (USGS site 372201081303501) and the abandoned public-supply water wells near Havaco, W. Va. (USGS site 372358081344601), had discharge in excess of 1.00 ft 3 /s. Discharge from the abandoned public supply wells was 3.685 ft 3 /s on September 20, 2023, and 2.888 ft 3 /s on October 16, 2023, and discharge from Harmon Branch at Thorpe, W. Va., was 1.049 ft 3 /s on September 22, 2023, and 1.038 ft 3 /s on October 17, 2023. Discharge in the abandoned underground mine air shaft (USGS site 372224081340901) could not be assessed, but the air shaft drains an abandoned mine that likely contains water stored in approximately 1.7 square miles (mi 2 ) of abandoned underground coal mines in the Pocahontas No. 3 coal seam, and possibly an additional 0.9 mi 2 of leakage from the overlying Pocahontas No. 4 coal seam. Discharge for the six sites measured for the study was measured during a period between September 20 and October 18, 2023, and corresponded to the 12th to the 15th percentile of flow-duration statistics for the Tug Fork downstream of Elkhorn Creek at Welch, W. Va. streamgage (USGS site 03212750). Water-quality data for the seven sites sampled overall were acceptable with respect to drinking water standards. Of the 203 constituents analyzed, only a few failed to meet applicable U.S. Environmental Protection Agency (EPA) drinking water standards. Iron exceeded the 300 micrograms per liter (μg/L) secondary maximum contaminant level (SMCL) at only 1 of the 7 sites (14.3 percent) sampled. Iron concentrations ranged from a minimum of less than (<) 5.00 μg/L to a maximum of 724 μg/L with a median concentration of 7.62 μg/L. Manganese exceeded the 50.0 μg/L SMCL at 2 of the 7 sites (28.6 percent) sampled. Manganese concentrations ranged from a minimum of 1.93 μg/L to a maximum of 271 μg/L with a median concentration of 4.03 μg/L. No sites sampled exceeded the arsenic maximum contaminant level (MCL) of 10 μg/L. Arsenic concentrations ranged from a minimum of <0.100 μg/L to a maximum of 2.35 μg/L with a median arsenic concentration of 0.200 μg/L. None of the seven sites sampled for selenium for this study exceeded the EPA MCL of 50.0 μg/L. Selenium concentrations ranged from a minimum of <0.050 μg/L to a maximum of 5.26 μg/L with a median concentration of 3.21 μg/L. All seven sites were sampled for volatile organic compounds (VOCs), semivolatile organic compounds (SVOCs), and polychlorinated biphenyls (PCBs), but most had concentrations below the detection limit. Of the 10 PCB compounds analyzed for the seven sites sampled, none contained detectable concentrations of PCBs or Aroclor compounds. Of the 44 SVOCs analyzed at each of the seven sites sampled, only 1 SVOC, acenaphthene, was detected, at a concentration of 0.02 μg/L. Of the 96 VOCs analyzed, from each of the seven sites sampled, only two were found at detectable concentrations. Trichloromethane was detected only at 1 of the 7 (14.3 percent) sites sampled at a concentration of 0.027 μg/L, and benzene was detected at the same site and 3 additional sites (4 of the 7 sites or 57.1 percent of the sites sampled) at concentrations of 0.028, 0.029, 0.021, and 0.035 μg/L, but none exceeded the EPA MCL for benzene of 5.00 μg/L. Total coliform bacteria are ubiquitous in the environment, and their presence only suggests the potential for contamination by near-surface processes. Escherichia coli ( E. coli ) bacteria are derived from either human or animal fecal material and can be an indicator of potential contamination by pathogenic bacteria or viruses. Total coliform bacteria were detected at all 7 sites sampled at concentrations ranging from 17.5 to greater than (>) 2,420 most probable number per 100 mL (MPN/100 mL) of sample, with a median total coliform concentration of 1,553 MPN/100 mL. Escherichia coli bacteria were detected at 4 of the 7 sites sampled at concentrations ranging from <1 to 11.9 MPN/100 mL, with a median E. coli concentration of 5.1 MPN/100 mL.

West Virginia

Near-fault amplification and ground motion variability during the 2019 Ridgecrest, California sequence

We estimate ground-motion variability near the 2019 M 7.1 Ridgecrest earthquake sequence. Accurate seismic hazard estimation requires understanding ground-motion spatial correlations, yet many studies lack the dense station coverage needed to resolve small-scale variability. The 2019 M 7.1 Ridgecrest earthquake sequence presents a unique opportunity to examine ground motions and their spatial correlations at a range of interstation distances. The permanent seismic network was augmented with hundreds of temporary stations including several fault-crossing nodal arrays. We compute the event ( δE i ) and within-event ( δW ij ) residuals from the observed peak ground velocity and peak ground acceleration data to isolate potential sources of ground-motion variability. We then compare δW ij between station pairs that record an event to understand the semivariance of the ground motion versus interstation distance. By fitting an exponential model to the semivariances, we determine a correlation range of 25 km for the Ridgecrest region. Although the exponential model fits the broad-scale increase of semivariance with interstation distance, we also observe smaller-scale trends. We find that ground motions are less correlated for station pairs that are near or across faults that ruptured during the 2019 Ridgecrest sequence. We also find large, positive median δW ij with relative values 2–3 times larger than nearby stations for individual stations’ near-fault traces. Near-fault amplification and greater ground-motion variability can delineate fault zones and may locally increase the seismic hazard.

California

Fiber-optic sensing for earthquake hazards research, monitoring and early warning

The use of fiber‐optic sensing systems in seismology has exploded in the past decade. Despite an ever‐growing library of ground‐breaking studies, questions remain about the potential of fiber‐optic sensing technologies as tools for advancing if not revolutionizing earthquake‐hazards‐related research, monitoring, and early warning systems. A working group convened to explore these topics; we comprehensively examined the application of fiber optics in various aspects of earthquake hazards, encompassing earthquake source processes, crustal imaging, data archiving, and technological challenges. There is great potential for fiber‐optic systems to advance earthquake monitoring and understanding, but to fully unlock their capabilities requires continued progress in key areas of research and development, including instrument testing and validation, increased dynamic range for applications focused on larger earthquakes, and continued improvement in subsurface and source imaging methods. A key current stumbling block results from the lack of clear data archiving requirements, and we propose an initial strategy that balances data volume requirements with preserving key data for a broad range of future studies. In addition, we demonstrate the potential for fiber‐optic sensing to impact monitoring efforts by documenting the data completeness in a number of long‐term experiments. Finally, we outline the features of a instrument testing facility that would enable progress toward reliable and standardized distributed acoustic sensing data. Overcoming these current obstacles would facilitate progress in fiber‐optic sensing and unlock its potential application to a broad range of earthquake hazard problems.

California, Oregon, Washington

Metaproteomics and metagenomics reveal microbial pathways of organic matter degradation and methanogenesis in a marginally producing natural gas well

The expansion of natural gas production and utilization worldwide has led to the decline of many once-productive wells, eventually resulting in costly well-plugging and unused infrastructure. However, in areas like the Michigan basin, MI, where the majority of natural gas is biogenically produced, microbial communities could potentially be stimulated to generate additional methane, increasing gas supply and reducing the need to drill new wells. In this study, we performed metaproteomic, metagenomic, and geochemical analyses of Antrim Shale formation water from a marginally producing natural gas well to evaluate resident microbial community functions in the context of potential bioenergy production. Functional proteins involved in methanogenesis, degradation/catabolism (including organic matter degradation), biosynthesis, energy utilization, transmembrane transport, and stress response were among the most commonly identified groups. Three metagenome-assembled genomes (MAGs) were characterized, including Methanomicrobiaceae, Methanothrix , and Smithella . For each, the identified proteins involved in methanogenesis and the degradation of diverse organic compounds, strongly suggest their role in utilizing shale-derived organic matter. These findings provide an increased understanding of the microorganisms and their metabolisms generating natural gas in the Antrim Shale and establish a foundation for future stimulation efforts aimed at enhancing biogenic methane production in marginal gas wells.

Michigan

U.S. Geological Survey geomagnetic variometer data: Capitalizing on seismic infrastructure

The U.S. Geological Survey’s Geomagnetism Program is collaborating with the Earthquake Hazards Program and Global Seismographic Network Program to densify magnetic field observations. This collaboration focuses on the installation of magnetometers, or magnetic variometers, at existing seismic stations. Along with improving the density of space weather observations for hazard monitoring, these data can be used to correct colocated magnetic field induced noise in seismic data. Such corrections are especially useful during time periods of large magnetic storms where the magnetic field‐induced instrument noise can be of similar amplitude to earthquake ground‐motion records.

contiguous United States

High-precision earthquake catalog for Minto Flats fault zone, central Alaska, reveals complex and conjugate faulting

The Minto Flats fault zone (MFFZ) in central Alaska is a left‐lateral strike‐slip fault system situated between the continental‐scale right‐lateral Denali and Kaltag‐Tintina faults. The MFFZ has the potential to generate magnitude 7 earthquakes, and it hosted a magnitude 6 earthquake in 1995. It has also produced exotic events, such as very‐low‐frequency earthquakes and nucleation signals. We use network‐matched filtering and relative earthquake relocation techniques to derive a detailed catalog of earthquake locations for the MFFZ. The catalog spans from August 2014 to December 2019, a time period including 13 temporary seismic stations in the region. Our results provide the most complete catalog for the MFFZ and include deeper events, clusters of shallow seismicity, and a complex and segmented fault structure not observed in the original regional catalog. We document right‐lateral strike‐slip faulting, conjugate to the main northeast‐striking left‐lateral faults of the MFFZ. Below Nenana basin, the relocated seismicity reveals northwest‐dipping left‐lateral faults, supporting the inference that deep crustal active faulting is associated with recent basin deformation.

Alaska

The influence of postfire root strength decay on shallow landslide susceptibility in western Oregon

Severe wildfires can increase the potential for postfire landslides, partly due to the loss of vegetation and root reinforcement. This study investigates the multi-year dynamics of root strength following wildfire in coniferous forests of western Oregon and evaluates implications for postfire slope stability. Root tensile strength was measured through laboratory testing of 969 roots collected from 26 test pits over four postfire timeframes: unburned conditions, 4–12 months postfire (Cedar Creek, 2022), 24–35 months postfire (Holiday Farm, 2020), and 59–67 months postfire (Eagle Creek, 2017). Variables analyzed include root diameter, tensile thread strength, stiffness, progressive tensile strength with displacement, time-dependent strength and ductility, root area ratio, and cohesion. Results indicate a 50% reduction in root strength after wildfire, with the lowest values occurring around 4 years postfire. Projections indicate it could take 10–22 years following fire for root strength to recover to 70% and 90% of the prefire original root strength, respectively. This timeline indicates a multi-year window of vulnerability for shallow landslides that reaches a maximum approximately 4 years following fire. Brittle failure behavior was observed in burned root systems compared to unburned root systems, signaling a more abrupt loss of strength at yield. Simple slope stability analyses show that reduced root strength can lead to instability on more gentle slopes and under less saturation in comparison to unburned conditions. These findings highlight the critical role of root reinforcement in postfire slope stability and the long-term implications of wildfire disturbance on landslide susceptibility.

Oregon

Wangyanite, PdNi8S8, a new Pd end-member mineral of the pentlandite group from the J-M reef, Stillwater Complex, Montana, USA

Wangyanite (IMA2024-008a), ideally PdNi 8 S 8 , is a Pd end-member mineral of the pentlandite group that was discovered in the J-M reef of the Stillwater Complex, Montana, USA. Wangyanite occurs as anhedral-subhedral granular crystals 200–400 µm in size, associated with isoferroplatinum, braggite, pentlandite, and chalcopyrite interstitial to plagioclase grains within anorthosite. Wangyanite exhibits a yellowish brown color with a black streak and a metallic luster. It is brittle with uneven fractures, and has a calculated density of 5.14 g/cm 3 . The mineral does not show discernible pleochroism, bireflectance, or anisotropy. It has an average composition of 9.95 wt.% Pd, 31.95 wt.% Ni, 25.02 wt.% Fe, 0.57 wt.% Co, 31.74 wt.% S, totaling 99.23 wt.%. The empirical formula, based on eight sulfur atoms per formula unit, is (Pd 0.76 Co 0.08 ) Σ0.84 (Ni 4.39 Fe 3.60 ) Σ7.99 S 8 . Wangyanite has a cubic cell with a space group of Fm -3 m (#225), having lattice parameters of a = 10.1167(12) Å, V = 1035.4(4) Å 3 , and Z = 4. Its crystal structure has been solved by single-crystal three-dimensional electron diffraction study. The strongest X-ray diffraction lines of wangyanite are claculated at [ d in Å ( I %)( hkl )]: 5.841(14.03)(111), 3.050(100)(311), 1.947(29.16)(115,333), 1.264(11.66)(800), 3.577(8.79)(220), 2.920(20.82)(222), and 2.321(9.34)(331). Wangyanite shares the same crystal structure as pentlandite, but the octahedrally coordinated site is mainly occupied by Pd in wangyanite. Based on the textural features and previous experimental Pd-Fe-Ni-S phase system, wangyanite could form by peritectic reaction between braggite, pentlandite and sulfide liquid. These mineral associations are stable in a Ni-Pd-rich sulfide melt system at about 550 °C or even lower temperature. Therefore, wangyanite can potentially serve as an indicator of the presence of Pd-rich residual melts. The mineral is named in honor of Prof. Christina Yan Wang, a well-known researcher on platinum-group element (PGE) occurrences and enrichment mechanisms in mafic-ultramafic intrusions, notably those deposits related to the Emeishan large igneous province in China.

Montana

Nodal seismic deployment on Mauna Loa volcano, Hawaii: Dataset and preliminary insights

Mauna Loa is the largest active volcano on Earth, comprising ∼51% of the Island of Hawai‘i’s landmass and posing significant risks to the island’s communities, infrastructure, and natural environment. Historical eruptions have produced lava flows that have reached the ocean in as little as 3 hr. The timing and location of such lava flows in the past 200 yr underscore how critical determination of the location and geometry of magma storage and structure is for volcanic hazard assessment and eruption forecasting. Now, after nearly 38 yr of volcanic quiescence, Mauna Loa has erupted again. On 27 November 2022, fissures initiated within the summit caldera and then migrated to the northeast rift zone, where they generated a large lava flow that threatened a major highway. To improve our understanding of the geometry of this magma system, we deployed a temporary nodal array on Mauna Loa in the summer of 2024. This increased our seismic coverage sufficiently to image this magmatic system. This nodal array consists of 33 seismometers distributed on and around the volcano and was deployed for over three months to record seismic signals. The primary objective of this project is to resolve the high‐resolution seismic velocity structure and characterize seismic features associated with magma storage and ascent pathways. In this article, we present an overview of the deployment, evaluate the quality of the data, and show example recordings to evaluate the suitability of the data set for future seismic investigations, including earthquake relocation, seismic tomography, and receiver function analysis. Comparisons with nearby permanent broadband and short‐period seismic stations demonstrate that the nodal array recorded high‐quality waveforms, making it a valuable resource for constraining the magmatic system beneath Mauna Loa at multiple scales.

Hawaii

Geochemical evidence for the origin of late Quaternary loess, Seward Peninsula, Alaska

Loess is the most widespread surficial deposit in the state of Alaska. Although loess of last glacial age is common in mid-continental North America, records of last glacial loess in Alaska have been elusive. Here we report a record of last glacial loess on the Seward Peninsula, along with studies of a transect of loess localities also thought to date to the last glacial period. Highly diverse hypotheses on the origin of loess on the Seward Peninsula include local volcanic rocks and mountain ranges to the north and south, as well as offshore deposits. We present particle size and mineralogical and geochemical data that indicate that the most likely sources for loess in this part of eastern Beringia are glaciogenic silt particles of the Kobuk River and Noatak River, both of which drain the Brooks Range to the northeast. Northeasterly paleowinds were therefore responsible for loess on the Seward Peninsula. Such winds probably occurred during late summer or early autumn, when river discharge was at a minimum but temperatures were still above freezing. Northeasterly winds during the last glacial period are in good agreement with a recent paleoclimate model.

Alaska

Rare earth element-mineralized carbonatite in the Bear Lodge Alkaline Complex, USA—Ore genesis implications from fluid inclusion characterization

Rare earth element (REE) resources of the Bear Lodge Alkaline Complex, Wyoming, are hosted in variably leached carbonatite spatially related to diatreme breccia pipes. We investigated the genesis of REE and lesser-known gold resources through fluid inclusion analysis of carbonatite, fluorite breccia, and smoky quartz vein samples. Physicochemical characteristics of inclusion-trapped fluids were evaluated using petrography, microthermometry, Raman spectroscopy, decrepitate mound analysis, energy-dispersive spectroscopy, laser ablation inductively coupled plasma mass spectrometry, and noble gas isotope analysis. Microthermometry results reveal three fluid types that affected carbonatite dikes within deeper zones that escaped near-surface, ore-grade REE enrichment: (1) high-temperature (330–432°C) magmatic fluid captured in fine-grained calcite; (2) REE-enriched alkali bicarbonate-sulfate brine; and (3) low-temperature (117–182°C) diluted magmatic or meteoric water. Multiphase brine-like inclusions contain burbankite, nahcolite, strontianite, celestine and alkali sulfate daughter crystals, linking them to early burbankite mineralization. Peripheral smoky quartz and fluorite occurrences at Smith Ridge, 1.5 km from the central carbonatite dike swarm, contain primary inclusions that are Cl-poor and rich in Na-HCO 3 -SO 4 , similar to secondary and pseudosecondary inclusions in carbonatites. Helium isotopes reveal a MORB-like source for carbonatite samples and an older crust signature at Smith Ridge, consistent with the proximal ridge-top exposures of Archean granite. Results from this fluid inclusion study coupled with previous studies of carbonatite mineral paragenesis, show that light REEs (LREEs) were not mobilized great distances. Instead, burbankite crystallized within carbonatite from alkali bicarbonate fluids. With sodium retained in early burbankite, outward-emanating fluids enriched in potassium relative to sodium (higher K:Na) resulted in potassium–ferric iron metasomatism of silicate host rocks. This alkali fractionation was accompanied by fractionation of LREEs and heavy REEs (HREEs), with LREEs dominating the central carbonatite resources. In contrast, areas of peripheral REE mineralization at Bear Lodge are commonly characterized by higher HREE:LREE ratios. The K:Na ratio of associated fenites or alteration assemblages could be indicative of early crystallized burbankite in carbonatites and REE fractionation processes potentially leading to areas of concentrated HREEs with greater supply vulnerabilities.

South Dakota, Wyoming

Subduction zone earthquake catalog separation tool: Implementation in the USGS 2025 Puerto Rico and U.S. Virgin Islands National Seismic Hazard Model

The U.S. Geological Survey (USGS) periodically releases updates to National Seismic Hazard Model (NSHM) for the United States and its territories leveraging current scientific knowledge and methodologies to guide public policy, building codes, and risk assessments regarding potential ground shaking due to earthquakes that may result in infrastructure damage. In subduction zones, there is a need to separate the earthquake catalog into tectonic regimes to create specific seismicity models for which the most appropriate ground‐motion models are then applied. Here, we describe newly developed methods and software, called CatSep, that classifies subduction zone events into three primary tectonic regimes: crustal, interface, and intraslab. This method incorporates information about the location of the earthquake relative to the subducting slab, the depth of the Mohorovičić discontinuity, and the earthquake’s moment tensor. Applying this method is a first step in the NSHM workflow for regions covering U.S. subduction zones. Results using this subduction zone earthquake catalog separation tool for the 2025 Puerto Rico and U.S. Virgin Islands NSHM earthquake catalog are presented and analyzed.

Puerto Rico, U.S. Virgin Islands

S/P amplitude ratios with Distributed Acoustic Sensing and application to earthquake focal mechanisms

Distributed acoustic sensing (DAS), which transforms a fiber optic cable into an array of high frequency strainmeters, has the potential to help us characterize earthquakes with a dense sampling of measurements. While earthquake focal mechanisms are frequently determined using P -wave polarities and S / P amplitude ratios with inertial seismometers, the dense sampling of DAS over potentially large portions of the focal sphere can aid our solutions. Here, we consider ∼200 regional earthquakes and thousands of S / P measurements on a DAS cable colocated with a network of inertial seismometers near Arcata, California. We demonstrate the S / P ratio measurements made on DAS are similar to those made on the inertial seismometers and can be used to constrain focal mechanism solutions.

California

Ubiquity and causes of soil water preferential flow across 17 ecoregions

Preferential flow (PF) in soil causes the rapid transport of water, nutrients, and contaminants into the subsurface, influencing groundwater recharge and streamflow. Data scarcity has hindered the quantification of PF occurrence and the identification of its drivers across diverse ecoregions. We address this gap by analyzing high-frequency, multi-depth soil moisture data across 17 ecoregions in the USA, using ∼1,500 sensors at 40 sites. We discovered that PF is widespread, with sites experiencing PF in up to 60% of rainfall events ≥2 mm. Multiple approaches consistently show that PF is more likely to occur with increased peak rainfall intensity, finer textured material, low soil moisture variability, humid climate, and higher net primary productivity. This suggests that PF patterns could shift with projected climate changes, increasing uncertainty in predictions of groundwater recharge, water quality, and streamflow generation.

conterminous United States and Puerto Rico

SURF: An automated method for building nonplanar 3D fault models from earthquake hypocenters

Accurately characterizing 3D fault geometry is vital for improving our understanding of earthquake behavior and informing the development of seismic hazard models. Despite their importance, subsurface fault structures tend to be poorly constrained because of limitations in observational data. Improvements to the seismic networks and earthquake detection algorithms have increased the precision and volume of earthquake catalogs, which help illuminate detailed subsurface fault structure and provide the most direct information available about fault geometries at depth. We present a Python package to automate generating 3D fault geometries directly from hypocentral seismicity patterns. This method begins with clustering events based on their spatial density, identifying coherent patterns. Nearby clusters are then merged based on the similarity of their orientations. We fit nonplanar surfaces using support vector regression to balance surface accuracy with minimal deviations from planarity. The fault models are output as quadrilateral meshes at user‐defined resolution. In the process of generating the 3D fault surfaces, we compute the spatial density of seismicity around the surface and the planarity as quantitative metrics of the model outputs. As a proof of concept, we apply this approach to the San Andreas–Calaveras fault junction region and the 2019 Ridgecrest earthquake sequence, both in California, which contain complex subparallel faults well defined at the Earth’s surface and abundant microseismicity. These case studies demonstrate the method’s ability to model complex fault structures, including long continuous fault surfaces, crossing faults, variably dipping segments, and subparallel faults. We test the method on both standard network catalogs and double‐difference relocated catalogs. We find that our seismicity‐based fault model results align with published 3D models that incorporate additional constraints and interpretations ( Plesch et al. , 2020 ; Aagaard and Hirakawa, 2021 ). This workflow provides a low‐user‐input solution for estimating fault geometries at depth from earthquake catalogs.

California

Submarine groundwater discharge creates cold‐water refugia that can mitigate exposure of heat stress in nearshore corals

Coral reef mortality around the world is accelerating due to human activities and rising sea temperatures that cause bleaching, which is expected to become more frequent. Our ability to predict which corals will be most resilient, however, remains limited due to insufficient information characterizing nearshore temperature and habitat conditions. In this study, we examine how submarine groundwater discharge (SGD) reduces nearshore water temperatures and exposure of corals to heat stress, complementing the understanding that SGD can adversely affect coral when it contains elevated nutrient concentrations. Data from fixed nearshore sensors and vertical depth profiles along ~100 km of the western shoreline of the Island of Hawai’i from 2003 to 2014 demonstrate that submarine groundwater discharge (SGD) can reduce nearshore water temperatures by 1 °C–5°C and create estuarine-like conditions with salinities as low as 20 PSU, where the prevalent coral species, Pocillopora meandrina, Porites lobata , and Montipora capitata , thrive. Time-series temperature records reveal that exposure to high ambient ocean temperatures, which are known to initiate bleaching events, are reduced up to 5%–46% of the time. Coral health surveys indicated coral bleaching in response to moderately high annual temperatures in 2010 and 2011, with more colonies affected farther from cold, SGD-fed waters. Synthesis of these results, along with coral response data following the more extreme marine heat wave of 2014–2015, demonstrates lower coral loss and greater coral recovery near groundwater seeps, particularly those with higher flux and influence on reducing nearshore water temperatures. Our results demonstrate that SGD may therefore provide a beneficial ecosystem service and enhance coral reef resilience, particularly where human-related nutrient additions to groundwater can be mitigated. The implications of our findings are relevant across tropical coasts where groundwater inputs can be substantial, such as the Caribbean and Indo-Pacific, and contribute to improving our understanding of coral sensitivity to gradients in temperature and nutrient stress. Improved management of groundwater resources could thus be vital to local–regional strategies for mitigating future heat stress.

Hawaii

Mapping a Carrington storm

A map is presented of median 1-min-resolution peak geoelectric-field strength across the United States as would be induced by magnetic storms as intense as the 2 September 1859 Carrington storm. The map is constructed from two data sets: Magnetometer time series from 22 ground-based observatories recording 40 magnetic storms, and surface impedance tensors derived from magnetotelluric measurements acquired at 1616 survey sites across the contiguous United States. Carrington-class storm geoelectric fields are likely to be very strong in the United States East and Midwest; > 5.00 V/km at many places. In Virginia, strengths would likely range from 30.30 V/km, with a 68% confidence interval of [19.44,47.20] V/km, to as low as 0.05 [0.03,0.07] V/km. Comparison of model geopotentials with those measured on 30 long lines, indicates errors of about 18%. A Carrington-class storm would likely induce geoelectric fields with strengths 55% greater than for the 13–14 March 1989 storm.

contiguous United States

Assessing flood water infiltration and storage in a restored floodplain

In urban areas, floodplain restoration is gaining prominence as a strategy for restoring the natural functions of floodplain ecosystems and reducing flood risk. This has spurred research into potential interactions between floodwaters, the hyporheic zone, and the floodplain aquifer. An urban restored stream in Wisconsin, USA, was used as a case study to examine four methods to estimate floodplain infiltration and storage during overbank floods. We characterised flood-related infiltration over a 4-year period from 2018 through 2021 by simultaneously and continuously measuring groundwater levels and vertical temperature profiles with stream water levels linked to high-resolution flood inundation maps. High-resolution topographic data helped to quantify surface floodplain storage and the unsaturated soil volume relative to flood stage. Infiltration estimates from the simple methods align well with those from the more complex methods; however, the complex methods provide additional insights about the factors influencing infiltration. Results from all methods indicate that the volume of water that vertically infiltrates during floods is likely small relative to the total volume of the flood, with 0.08%–0.52% of flood water infiltrating into the floodplain, on average. Spatially variable vertical hydraulic gradients, driven by flood depth, groundwater level, and permeability, imply heterogeneous patterns of infiltration across the floodplain. Gradients favourable for infiltration typically occurred during the onset of flooding but, over the study period, were mostly (98% of the time) favourable for groundwater discharge to the channel (non-flood periods). These findings highlight the importance of considering surface-groundwater dynamics, floodplain soils, and unsaturated floodplain volume in defining the benefits of floodplain infiltration for flood attenuation.

Wisconsin