Geology Reports⌕ Search

Geology topics

Research about Illinois Basin

Source-linked reports with geographic coverage including Illinois Basin.

14 recordsLinked to original sources
USGS2025

Estimation of dynamic geologic CO2 storage resources in the Illinois Basin, including effects of brine extraction, anisotropy, and hydrogeologic heterogeneity

Since the vast majority of carbon dioxide (CO 2 ) storage resources in the United States are in deep saline aquifers, optimizing the use of these saline storage resources could be crucial for efficient development of geologic CO 2 storage (GCS) resources and basin- or larger-scale deployment of GCS in the country. Maximum CO 2 injection rates can be enhanced by extracting brine from the CO 2 storage unit. However, disposal of the extracted brine is both a technological and economic challenge. The lowest-cost option would likely be reinjection of the extracted brine into another formation above or below the CO 2 storage unit. Therefore, it is important to estimate brine injectivity as it will constrain the potential to increase CO 2 injectivity at an injection site that has access to multiple geologic storage units where either CO 2 or brine can be injected. Using a simulation-optimization framework, coupled with a non-isothermal, multiphase CO 2 -water-salt equation-of-state module, we developed a computationally efficient method for evaluating optimization of simultaneous CO 2 injection, brine extraction, and brine (re)injection at hypothetical injection sites deployed across a geologic basin. The Illinois basin is ideal for testing our methodology because it contains multiple geologic storage units with seals in between them to isolate injection of CO 2 in one unit from interfering with the injection of either brine or CO 2 in another unit above or below it. In addition, we investigated the relative effects of variation in key geologic parameters as well as two reservoir structures (hydrogeologic heterogeneity/anisotropy and homogeneity/isotropy) on CO 2 injectivities and enhancement of CO 2 injectivity through extracting brine. Results suggest that permeability, depth, and especially thickness of the storage unit could be the most influential parameters determining CO 2 injectivity. They also suggest that only injecting CO 2 into the storage unit with the greatest injectivity, enhancing that unit’s injectivity by extracting brine, and disposing of the produced brine in other suitable units could maximize total CO 2 injectivity in limited regions of the basin. At the majority of simulated injection sites, however, we found that injecting CO 2 into all of the accessible and suitable storage units was more likely to maximize the CO 2 storage resource.

Illinois, Kentucky, Indiana↗
USGS2025

The impact of burial diagenesis on soil-formed minerals in paleosols using stable isotopes of phyllosilicates and carbonate clumped isotopes

To understand the effects of burial diagenesis on the stable isotope geochemistry of soil-formed clay and carbonate minerals in paleosols, samples were collected from seven cores, spanning middle- to upper-Pennsylvanian strata of the Illinois Basin, with varied maximum burial depths of 1–3 km. Mixed-layer illite-smectite and kaolinite mixtures give δ 2 H and δ 18 O values of −83 ‰ to −36 ‰ and 11.9 ‰ to 21.1 ‰ (VSMOW), respectively. After carbonates were screened petrographically for diagenetic textures using transmitted light and cathodoluminescence, measured clumped isotope Δ 47 values range from 0.504 to 0.563 ‰ (I-CDES). Resulting mineral formation temperatures for phyllosilicate mineral mixtures are 28 to 66 °C (mean = 47 °C), whereas T(Δ 47 ) estimates for calcites are 36 to 61 °C (mean = 45 °C). Calculated δ 18 O water values from which phyllosilicate minerals and calcites precipitated under isotopic equilibrium ranges from −7.1 to −1.2 ‰ and − 1.4 to +4.9 ‰, respectively. Closed and open-system phyllosilicate-fluid exchange modeling indicates that phyllosilicate alteration occurred in the presence of a low temperature brine or meteoric water and is interpreted to occur in a layer-by-layer illitization transformation. Due to the lack of diagenetic textures and positively correlated T(Δ 47 ) and δ 18 O water , calcites are interpreted to have undergone solid-state bond reordering. Despite low to moderate temperatures (<125 °C) and varying depths of shallow burial (1–3 km), solid-state transformation of phyllosilicates and calcites indicates paleosols had prolonged exposure to burial conditions which has implications for the use of paleosol minerals for paleoenvironmental reconstructions.

Illinois, Indiana, Kentucky↗
USGS2022

Dynamic estimates of geologic CO2 storage resources in the Illinois Basin constrained by reinjectivity of brine extracted for pressure management

Geologic carbon storage (GCS) is likely to be an important part of global efforts to decarbonize the energy industry. Widespread deployment of GCS relies on strategies to maximize CO 2 injection rates while minimizing reservoir pressurization that could induce seismicity and/or fluid leakage into groundwater resources. Brine extraction from CO 2 storage formations with subsurface reinjection elsewhere could mitigate pressure buildup associated with GCS. Therefore, evaluation of CO 2 storage resources should consider the injectivity of produced brine in geologic layers above or below the CO 2 storage formation. For this study, a methodology was developed to estimate brine injectivity from formation depth and thickness using flow modeling and optimization techniques. The methodology was demonstrated in the Illinois Basin, where GCS in the Mt. Simon Sandstone is ongoing. Based on pressure constraints and considering only regions of the shallower units where salinity and sealing conditions were met, maximum brine injection rates were estimated within the Mt. Simon and three overlying hydrostratigraphic layers. Results indicate that a large area exists where CO 2 injectivity could be optimized by brine extraction and reinjection.

Illinois, Indiana↗
USGS2011

Characterizing near-surface CO2 conditions before injection - Perspectives from a CCS project in the Illinois Basin, USA

The Midwest Geological Sequestration Consortium is conducting a large-scale carbon capture and storage (CCS) project in Decatur, Illinois, USA to demonstrate the ability of a deep saline formation to store one million tonnes of carbon dioxide (CO 2 ) from an ethanol facility. Beginning in early 2011, CO 2 will be injected at a rate of 1,000 tonnes/day for three years into the Mount Simon Sandstone at a depth of approximately 2,100 meters. An extensive Monitoring, Verification, and Accounting (MVA) program has been undertaken for the Illinois Basin Decatur Project (IBDP) and is focused on the 0.65 km2 project site. Goals include establishing baseline conditions to evaluate potential impacts from CO 2 injection, demonstrating that project activities are protective of human health and the environment, and providing an accurate accounting of stored CO 2 . MVA efforts are being conducted pre-, during, and post- CO 2 injection. Soil and net CO 2 flux monitoring has been conducted for more than one year to characterize near-surface CO 2 conditions. More than 2,200 soil CO 2 flux measurements have been manually collected from a network of 118 soil rings since June 2009. Three ring types have been evaluated to determine which type may be the most effective in detecting potential CO 2 leakage. Bare soil, shallow-depth rings were driven 8 cm into the ground and were prepared to minimize surface vegetation in and near the rings. Bare soil, deep-depth rings were prepared similarly, but were driven 46 cm. Natural-vegetation, shallow-depth rings were driven 8 cm and are most representative of typical vegetation conditions. Bare-soil, shallow-depth rings had the smallest observed mean flux (1.78 μmol m −2 s −1 ) versus natural-vegetation, shallow-depth rings (3.38 μmol m −2 s −1 ). Current data suggest bare ring types would be more sensitive to small CO 2 leak signatures than natural ring types because of higher signal to noise ratios. An eddy covariance (EC) system has been in use since June 2009. Baseline data from EC monitoring is being used to characterize pre-injection conditions, and may then be used to detect changes in net exchange CO 2 fluxes (Fc) that could be the result of CO 2 leakage into the near-surface environment during or following injection. When injection at IBDP begins, soil and net CO 2 monitoring efforts will have established a baseline of near-surface conditions that will be important to help demonstrate the effectiveness of storage activities.

Illinois↗
USGS2011

Applying monitoring, verification, and accounting techniques to a real-world, enhanced oil recovery operational CO2 leak

The use of carbon dioxide (CO 2 ) for enhanced oil recovery (EOR) is being tested for oil fields in the Illinois Basin, USA. While this technology has shown promise for improving oil production, it has raised some issues about the safety of CO 2 injection and storage. The Midwest Geological Sequestration Consortium (MGSC) organized a Monitoring, Verification, and Accounting (MVA) team to develop and deploy monitoring programs at three EOR sites in Illinois, Indiana, and Kentucky, USA. MVA goals include establishing baseline conditions to evaluate potential impacts from CO 2 injection, demonstrating that project activities are protective of human health and the environment, and providing an accurate accounting of stored CO 2 . This paper focuses on the use of MVA techniques in monitoring a small CO 2 leak from a supply line at an EOR facility under real-world conditions. The ability of shallow monitoring techniques to detect and quantify a CO 2 leak under real-world conditions has been largely unproven. In July of 2009, a leak in the pipe supplying pressurized CO 2 to an injection well was observed at an MGSC EOR site located in west-central Kentucky. Carbon dioxide was escaping from the supply pipe located approximately 1 m underground. The leak was discovered visually by site personnel and injection was halted immediately. At its largest extent, the hole created by the leak was approximately 1.9 m long by 1.7 m wide and 0.7 m deep in the land surface. This circumstance provided an excellent opportunity to evaluate the performance of several monitoring techniques including soil CO 2 flux measurements, portable infrared gas analysis, thermal infrared imagery, and aerial hyperspectral imagery. Valuable experience was gained during this effort. Lessons learned included determining (1) hyperspectral imagery was not effective in detecting this relatively small, short-term CO 2 leak, (2) even though injection was halted, the leak remained dynamic and presented a safety risk concern during monitoring activities and, (3) the atmospheric and soil monitoring techniques used were relatively cost-effective, easily and rapidly deployable, and required minimal manpower to set up and maintain for short-term assessments. However, characterization of CO 2 distribution near the land surface resulting from a dynamic leak with widely variable concentrations and fluxes was challenging.

Illinois, Indiana, and Kentucky↗
USGS2011

Meeting CCS communication challenges head-on: Integrating communications, planning, risk assessment, and project management

The Midwest Geological Sequestration Consortium, Schlumberger Carbon Services, and Archer Daniels Midland has implemented a comprehensive communications plan at the Illinois Basin–Decatur Project (IBDP), a one million metric tonne Carbon Capture and Storage project in Decatur, IL, USA funded by the U.S. Department of Energy’s National Energy Technology Laboratory. The IBDP Communication Plan includes consortium information, funding and disclaimer citations, description of target audiences, media communications guidelines, paper and presentations guidelines, site visit information, crisis communication, on-site photography regulations, and other components. The creation, development, and implementation processes for the IBDP Communication Plan (the Plan) are shared in this paper. New communications challenges, such as how to address add-on research requests, data sharing and management, scope increase, and contract agreements have arisen since the Plan was completed in January 2009, resulting in development of new policies and procedures by project management. Integrating communications planning, risk assessment, and project management ensured that consistent, factual information was developed and incorporated into project planning, and constitutes the basis of public communications. Successful integration has allowed the IBDP to benefit from early identification and mitigation of the potential project risks, which allows more time to effectively deal with unknown and unidentified risks that may arise. Project risks and risks associated with public perception can be managed through careful planning and integration of communication strategies into project management and risk mitigation.

Illinois↗
USGS2007

Assessment of Undiscovered Oil and Gas Resources of the Illinois Basin, 2007

Using a geology-based assessment methodology, the U.S. Geological Survey estimated the following quantities of undiscovered, technically recoverable oil and gas resources in the Illinois Basin, USA: (1) a mean of 214 million barrels of oil; (2) a mean of 4.65 trillion cubic feet of natural gas; and (3) a mean of 24 million barrels of natural gas liquids.

Illinois Basin↗
USGS2001

Regional fluid migration in the Illinois basin: Evidence from in situ oxygen isotope analysis of authigenic K-feldspar and quartz from the Mount Simon Sandstone

Oxygen isotope compositions of widespread, authigenic K-feldspar and quartz overgrowths and cements in the Upper Cambrian Mount Simon Sandstone were measured by ion microprobe in 11 samples distributed across the Illinois basin and its periphery. Average K-feldspar δ 18 O values increase systematically from +14‰ ± 1‰ in the southernmost and deepest samples in Illinois to +24‰ ± 2‰ in the northernmost outcrop sample in Wisconsin. A similar trend was observed for quartz overgrowths (22‰ ± 2‰ to 28‰ ± 2‰). Constant homogenization temperatures (100–130 °C) of fluid inclusions associated with quartz overgrowths throughout the basin suggest that the geographic trend in oxygen isotope compositions is a result of diagenetic modification of a south to north migrating basinal fluid.

Illinois, Indiana, Kentucky↗
USGS1993

Proterozoic crustal boundary in the southern part of the Illinois Basin

Recently acquired COCORP and proprietary seismic reflection data in the southern part of the Illinois Basin, combined with other geological and geophysical data, indicate that a WNW-trending Proterozoic terrane boundary (40 km wide) lies within basement. The boundary is characterized by the termination of subhorizontal Proterozoic reflectors and associated diffraction patterns along a line coinciding with the major magnetic lineament in this region (South Central Magnetic Lineament). North of the boundary, where reflectors thought to represent a sequence of layered Proterozoic rocks in the upper crust are widespread and as much as 11 km thick, total magnetic intensity values are relatively high, suggesting layers of rock with high magnetic susceptibility. To the south, the Proterozoic rocks are acoustically transparent on seismic reflection sections and total magnetic intensity values are relatively low. Moreover, relatively high Bouguer gravity anomaly values to the south may be caused by a dense, altered, lower crustal layer similar to that interpreted from deep seismic refraction studies to underlie the northern Mississippi Embayment. The boundary lies along the projected trend of the northern margin of the Early Proterozoic Central Plains orogen and we suggest that it marks the convergent margin of this orogen. Reactivation of the boundary and the associated zone of weakness during late Paleozoic times apparently resulted in structural deformation in the southern part of the Illinois Basin, including movement along the Cottage Grove Fault System and Ste. Genevieve Fault Zone and igneous activity at Hicks Dome. In addition to the role played by this crustal boundary in the evolution of the Illinois Basin, its location between the Wabash Valley Seismic Zone to the northeast and the New Madrid Seismic Zone to the southwest may be a significant factor in present-day seismicity.

Illinois, Indiana, Kentucky, Missouri↗
USGS1987

Use of stable sulphur isotopes to monitor directly the behaviour of sulphur in coal during thermal desulphurization

A method has been developed using stable sulphur isotope analyses to monitor the behaviour of sulphur forms in a coal during thermal desulphurization. In this method, the natural stable isotopic composition of the pyritic and organic sulphur in coal is used as a tracer to follow their mobility during the desulphurization process. This tracer method is based on the fact that the isotopic compositions of pyritic and organic sulphur are significantly different in some coals. Isotopic results of pyrolysis experiments at temperatures ranging from 350 to 750 °C indicate that the sulphur released with the volatiles is predominantly organic sulphur. The pyritic sulphur is evolved in significant quantities only when pyrolysis temperatures exceed 500 °C. The presence of pyrite seems to have no effect on the amount of organic sulphur evolved during pyrolysis. The chemical and isotopic mass balances achieved from three different samples of the Herrin (No. 6) coal of the Illinois Basin demonstrate that this stable isotope tracer method is quantitative. The main disadvantage of this tracing technique is that not all coals contain isotopically distinct organic and pyritic sulphur.

Illinois, Indiana, Kentucky↗
USGS1984

Coalification of organic matter in coal balls of the Pennsylvanian (upper Carboniferous) of the Illinois Basin, United States

An evaluation was made of the degree of coalification of two coal balls from the Illinois Basin of the Pennsylvanian (upper Carboniferous) of the United States. Previous interpretations are mainly misleading and contradictory, primarily because of the assumption that the brown color and exceptional cellular and subcellular preservation typical of American coal balls imply chemical preservation of cellulose and lignin, the primary components of peat. Xylem tissue from a medullosan seed fern contained in a coal ball and the coal attached to the coal ball from the Calhoun coal bed, Mattoon Formation, Illinois, was analyzed by elemental, petrographic, and nuclear magnetic resonance (NMR) techniques to determine the degree of coalification. The NMR and elemental data indicate the lack of cellulose and lignin and a probable rank of high-volatile C bituminous coal. These data corroborate data for a coal ball from the Herrin (No. 6) coal bed (Carbondale Formation, Middle Pennsylvanian) and support our hypothesis that the organic matter in coal balls of the Pennsylvanian strata of the United States is coalified to about the same degree as the surrounding coal. Data presented show a range of lower reflectances for xylem tissue and vitrinite in the analyzed coal balls compared with vitrinite in the attached coal. The data reported indicate that physical preservation of organic matter in coal balls does not imply chemical preservation. Also our study supports the hypothesis that compactional (static load) pressure is not a prerequisite for coalification up to a rank of high-volatile C bituminous coal. A whole-rock analysis of the Calhoun coal ball indicates a similarity to other carbonate coal balls from the United States. It consists primarily of calcium carbonate and 1–2% organic matter; silica and alumina together make up less than 0.5%, indicating the lack of minerals such as quartz and clays.

Illinois, Indiana, Kentucky↗