Geology topics

Research about Broome County, New York

Source-linked reports with geographic coverage including Broome County, New York.

6 recordsLinked to original sources

USGS2021

Hydrogeology of the Susquehanna River valley-fill aquifer system in the towns of Conklin and Kirkwood, Broome County, New York

The hydrogeology of the Susquehanna River valley-fill aquifer system and adjacent areas in south-central Broome County, New York, was investigated in cooperation with the New York State Department of Environmental Conservation. The study area encompasses roughly 55.5 square miles and includes the towns of Conklin and Kirkwood. Multiple small, perhaps discontinuous, valley-fill aquifers of unknown extent and hydraulic interconnection underlie the Susquehanna River valley from easternmost Binghamton south to Riverside, New York, near the Pennsylvania border. The hydrogeologic framework of these aquifers is described in this report on the basis of existing descriptions of surficial materials, especially those related to deglaciation, and subsurface data extracted from well and boring logs. A compilation of surficial geology, the descriptions of the spatial distribution of confined and unconfined aquifers, hydrogeologic sections, and well locations is provided as an oversized map plate and in a U.S. Geological Survey data release. Residential households are one of the principal consumers of groundwater in the study area. Approximately half of these households are served by public water-supply systems that obtain water from wells, chiefly from highly productive but small and likely discontinuous surficial deposits of sand and gravel, while others obtain water from sand-and-gravel aquifers beneath till and (or) fine-grained lacustrine deposits, and a few from bedrock. Residents outside the public-supply service areas rely on private wells. In till-mantled upland areas, nearly all private wells tap bedrock. Water-resource potential is likely greatest north of Kirkwood Center, New York, where the valley is narrowest, and local aquifers are in thick stratified glacial deposits. Well yields are highest in this part of the valley, and the local aquifer system is likely replenished through induced infiltration from the Susquehanna River and numerous small tributaries. The area between Langdon and Kirkwood is filled with a mixture of stratified and unstratified glacial sediments and contains one high-yield well. This area likely has moderate water-resource potential, but limited well data make this difficult to verify. Well yields from suitable stratified glacial sediments generally decrease southward toward Riverside, New York. Characterizing potential groundwater resources is also helpful for prioritizing source-water-protection efforts. Water resources throughout New York are at risk of contamination from commercial and industrial surface activities. As in many valley areas throughout the Susquehanna River watershed in south-central New York, valley wells with depths greater than roughly 100 to 150 feet are susceptible to contamination by naturally occurring saltwater and methane. New York currently has a moratorium on hydraulic fracturing, but the study area is underlain by rocks suitable for unconventional methods of gas production that would likely be initiated if the moratorium were to be lifted.

New York↗

USGS2015

Hydrogeology of the Susquehanna River valley-fill aquifer system in the Endicott-Vestal area of southwestern Broome County, New York

The village of Endicott, New York, and the adjacent town of Vestal have historically used groundwater from the Susquehanna River valley-fill aquifer system for municipal water supply, but parts of some aquifers in this urban area suffer from legacy contamination from varied sources. Endicott would like to identify sites distant from known contamination where productive aquifers could supply municipal wells with water that would not require intensive treatment. The distribution or geometry of aquifers within the Susquehanna River valley fill in western Endicott and northwestern Vestal are delineated in this report largely on the basis of abundant borehole data that have been compiled in a table of well records. Early in deglaciation, meltwater deposited sand and gravel in channels within or beneath the decaying ice and as narrow terraces along the valley walls. These ice-contact deposits vary widely over short distances from clean (free of silt) and highly permeable to clogged with silt and poorly permeable, but collectively constitute the principal aquifers in Endicott and Vestal. Some ice-contact deposits form a buried ridge, deposited in a meltwater channel within the ice sheet, that approximately underlies the Susquehanna River and (or) its north bank from Endwell westward to Nanticoke Creek and has been tapped by several municipal and industrial wells. Similar but thinner ice-contact deposits discontinuously underlie the valley floor to the south in Vestal, and a smaller buried ridge of ice-contact deposits is likely beneath or west of Nanticoke Creek south of West Corners. As deglaciation continued, a large lake developed; thick deposits of gray silt with red clay layers are continuous north of the Susquehanna River from Endwell to West Endicott, and similar deposits are present discontinuously elsewhere. Late in deglaciation, meltwater deposited highly permeable pebbly sand atop the valley fill, generally atop lacustrine silt. The saturated thickness of this surficial sand is seldom great enough to support large-capacity wells, but where it directly overlies ice-contact deposits it facilitates recharge from precipitation and infiltration of river water to the deeper aquifers. Three localities in Endicott were identified where thick ice-contact deposits capable of supporting municipal supply wells are documented by test wells or extrapolated to be present from nearby data and depositional history. Chemical analyses of water samples disclosed no contaminants in these localities when sampled, but the presence of contaminants or natural high iron a few thousand feet away from each locality is documented.

New York↗

USGS2001

Simulation of a valley-fill aquifer system to delineate flow paths, contributing areas, and traveltime to wellfields in southwestern Broome County, New York

A valley-fill aquifer system that extends along a 14-mile reach of the Susquehanna River valley in southwestern Broome County, N.Y., is a major source of water supply to local municipalities and industries, but is highly susceptible to contamination from human activities. Protection of ground-water supplies requires accurate delineation of the areas that are the sources of water pumped by wells. A previously developed two-layer steady-state ground-water flow model of the aquifer system was upgraded with an improved method of simulating stream-aquifer interactions, then recalibrated and coupled to a particle-tracking program. Three-dimensional, ground-water flow modeling coupled with particle tracking is the most reliable method of simulating groundwater flow paths in multiaquifer systems such as this; it also allows delineation of contributing areas to well.elds. A primary advantage of three-dimensional particle-tracking analysis is that it shows the complexities of the flow paths in each aquifer. Model and particle tracking analyses indicate that groundwater frequently follows convoluted three-dimensional flow paths. The contributing areas of individual supply wells in this aquifer system each has a unique flow pattern and shape. Results of the model simulation indicate that recharge from precipitation, rivers, and tributaries contribute 35 percent, 29 percent, and 25 percent, respectively to the aquifer system and that pumpage from supply wells accounts for 67 percent of the discharge from the aquifer system. Particle-tracking results indicate that the simulated contributing areas to the 24 supply wells includes most of the valley floor.

New York↗

USGS1993

Estimation of hydraulic conductivity of a riverbed and aquifer system on the Susquehanna River in Broome County, New York

A three-dimensional finite-difference model of groundwater flow was used to estimate the hydraulic conductivity of riverbed and aquifer material in a 1-square-mile valley-fill aquifer system near a large river in which induced infiltration due to pumping cannot be measured directly. The aquifer consists of a 30- to 70-foot thickness of sand and gravel containing discontinuous layers of compact and silty sand and gravel. Horizontal hydraulic conductivity of the aquifer material, estimated through trial-and-error calibration of simulated water levels to drawdowns measured during an aquifer test, ranged from 500 to 10,000 feet per day; anisotropy (ratio of horizontal to vertical hydraulic conductivity) ranged from 125:1 to 250:1. The vertical hydraulic conductivity of the riverbed was estimated to be 0.1 to 0.5 foot per day, whereas permeameter tests on samples of silty sand and gravel layers from the riverbed yielded vertical hydraulic conductivity of 10 -3 foot per day. A sensitivity analysis indicated that a narrow range of anisotropy values gave the smallest residual error in simulated drawdowns. Residual error increased sharply when the maximum hydraulic conductivity value for the aquifer was lowered to less than 5,000 feet per day. Residual error also was large for large values of vertical hydraulic conductivity of the riverbed, but decreased to a constant amount for values less than 0.1 foot per day. Residual error was relatively insensitive to changes in the storage coefficient and specific yield. A nonlinear regression method that approximated the sensitivity matrix with a perturbation technique was applied to refine the estimates of these parameters and compute standard error of the estimates. The nonlinear regression indicated that the model was sensitive to hydraulic conductivity of the aquifer and anisotropy of the upper part of the aquifer but not to anisotropy of the lower part, and that vertical hydraulic conductivity of the riverbed was less than 0.5 foot per day. The regression method yielded aquifer hydraulic-conductivity values of 210 to 13,000 feet per day and an anisotropy ratio of 350:1 for the upper part of the aquifer; the standard error of these estimates was relatively small. In contrast, the standard errors of estimates of anisotropy in the lower part of the aquifer and the vertical hydraulic conductivity of the riverbed were extremely large.

New York↗

USGS1986

Simulation of ground-water flow and infiltration from the Susquehanna River to a shallow aquifer at Kirkwood and Conklin, Broome County, New York

A four-layer finite difference model was developed to simulate groundwater flow and induced infiltration to an aquifer underlying the Susquehanna River in the Towns of Kirkwood and Conklin in Broome County, NY. The aquifer consists of sand and gravel deposited in an ancestral river valley during the recession of glacial ice and is in hydraulic connection with the Susquehanna River. In 1984, he aquifer supplied 1.2 million gal/day to well fields in Kirkwood and Conklin. Horizontal hydraulic conductivity of the sand and gravel in the calibrated model ranges from 50 to 10,000 ft/day. Vertical hydraulic conductivity ranges from 1.0 to 80 ft/day. The riverbed thickness was estimated from results of piezometer tests to be 2 ft; the hydraulic conductivity of the riverbed was estimated to be 0.2 ft/day. Root-mean-square differences between computed drawdowns and drawdowns measured in observation wells and piezometers during aquifer tests at the Kirkwood well field ranged from 17% to 24%. The sizes of the well field catchment areas were estimated from a model generated flow net showing the direction and rate of groundwater flow. The Kirkwood catchment area was estimated to be 250 acres, and the Conklin catchment area was 51 acres. Groundwater budgets computed by steady-state simulations showed that 58% of the groundwater withdrawn by the Kirkwood well field is derived from the Susquehanna River during the periods of low river stage and low recharge. The factor to which induced-infiltration rate and size of well field catchment areas are most sensitive, is riverbed hydraulic conductivity.

New York↗

USGS1982

Geohydrology of the valley-fill aquifer in the Endicott-Johnson City area, Broome County, New York

This report is the tenth in a series of 11 map sets depicting geohydrologic conditions in selected aquifers in upstate New York. Geohydrologic data are compiled on five maps at 1:24,000 scale. Together, the maps provide a comprehensive overview of a major valley-fill aquifer in southwestern Broome County. The maps include surficial geology, geologic sections, aquifer thickness, water-infiltration potential of soil zone, potentiometric-surface altitude, and land use. The valley-fill deposits consist of alluvial silt and sand, glacial outwash (sand and gravel), ice-contact sand and gravel, till, and lacustrine silt and clay. The sand and gravel beds have relatively high permeabilities whereas the till, silt, and clay deposits have relatively low permeabilities. Water-table conditions are found in unconfined sand and gravel, whereas artesian conditions prevail within sand and gravel confined by silty deposits. Recharge occurs over the entire surface of the aquifer, due to permeable land-surface conditions, but is greatest along the margin of the valley, where runoff from the hillsides is concentrated, and near streams. The use of land overlying the aquifer is predominantly commercial and residential with lesser amounts of agricultural and industrial uses. (USGS)

New York↗