Geology topics

Research about Bemidji, Minnesota

Source-linked reports with geographic coverage including Bemidji, Minnesota.

28 records · Page 2Linked to original sources

USGS2014

Effects of a dual-pump crude-oil recovery system, Bemidji, Minnesota, USA

A crude-oil spill occurred in 1979 when a pipeline burst near Bemidji, MN. In 1998, the pipeline company installed a dual-pump recovery system designed to remove crude oil remaining in the subsurface at the site. The remediation from 1999 to 2003 resulted in removal of about 115,000 L of crude oil, representing between 36% and 41% of the volume of oil (280,000 to 316,000 L) estimated to be present in 1998. Effects of the 1999 to 2003 remediation on the dissolved plume were evaluated using measurements of oil thicknesses in wells plus measurements of dissolved oxygen in groundwater. Although the recovery system decreased oil thicknesses in the immediate vicinity of the remediation wells, average oil thicknesses measured in wells were largely unaffected. Dissolved-oxygen measurements indicate that a secondary plume was caused by disposal of the pumped water in an upgradient infiltration gallery; this plume expanded rapidly immediately following the start of the remediation in 1999. The result was expansion of the anoxic zone of groundwater upgradient and beneath the existing natural attenuation plume. Oil-phase recovery at this site was shown to be challenging, and considerable volumes of mobile and entrapped oil remain in the subsurface despite remediation efforts.

Minnesota↗

USGS2014

A mass balance approach to investigating geochemical controls on secondary water quality impacts at a crude oil spill site near Bemidji, MN

Secondary water quality impacts can result from a broad range of coupled reactions triggered by primary groundwater contaminants. Data from a crude-oil spill research site near Bemidji, MN provide an ideal test case for investigating the complex interactions controlling secondary impacts, including depleted dissolved oxygen and elevated organic carbon, inorganic carbon, CH 4 , Mn, Fe, and other dissolved ions. To better understand these secondary impacts, this study began with an extensive data compilation of various data types, comprising aqueous, sediment, gas, and oil phases, covering a 260 m cross-sectional domain over 30 years. Mass balance calculations are used to quantify pathways that control secondary components, by using the data to constrain the sources and sinks for the important redox processes. The results show that oil constituents other than BTEX (benzene, toluene, ethylbenzene, o -, m - and p -xylenes), including n -alkanes and other aromatic compounds, play significant roles in plume evolution and secondary water quality impacts. The analysis underscores previous results on the importance of non-aqueous phases. Over 99.9% of the Fe 2+ plume is attenuated by immobilization on sediments as Fe(II) and 85–95% of the carbon biodegradation products are outgassed. Gaps identified in carbon and Fe mass balances and in pH buffering mechanisms are used to formulate a new conceptual model. This new model includes direct out-gassing of CH 4 and CO 2 from organic carbon biodegradation, dissolution of directly produced CO 2 , and sorption with H + exchange to improve pH buffering. The identification of these mechanisms extends understanding of natural attenuation of potential secondary impacts at enhanced reductive dechlorination sites, particularly for reduced Fe plumes, produced CH 4 , and pH perturbations.

Minnesota↗

USGS2014

Comparison of surficial CO2 efflux to other measures of subsurface crude oil degradation

At a spill site near Bemidji, Minnesota, crude oil at the water table has been undergoing anaerobic biodegradation for over 30 years. Previous work at this site has shown that methane produced from biodegradation of the oil migrates upward and is oxidized in a methanotrophic zone midway between the water table and the surface. To compare microbial activity measurement methods from multiple locations in the oil body, surficial carbon dioxide efflux, methanogen and methanotroph concentrations, and oil degradation state were collected. Carbon dioxide effluxes over the oil body averaged more than four times those at the background site. Methanotrophic bacteria concentrations measured using pmoA were over 10 5 times higher above the oil-contaminated sediments compared with the background site. Methanogenic archaea measured using mcrA ranged from 10 5 to over 10 7 in the oil and were below detection in the background. Methanogens correlated very well with methanotroph concentrations (r = 0.99), n-alkylcyclohexane losses as a proxy for degradation state (r = − 0.96), and somewhat less well with carbon dioxide efflux (r = 0.92). Carbon dioxide efflux similarly correlated to methanotroph concentrations (r = 0.90) and n-alkylcyclohexane losses (r = − 0.91).

Minnesota↗

USGS2011

Loss of volatile hydrocarbons from an LNAPL oil source

The light nonaqueous phase liquid (LNAPL) oil pool in an aquifer that resulted from a pipeline spill near Bemidji, Minnesota, was analyzed for volatile hydrocarbons (VHCs) to determine if the composition of the oil remains constant over time. Oil samples were obtained from wells at five locations in the oil pool in an anaerobic part of the glacial outwash aquifer. Samples covering a 21-year period were analyzed for 25 VHCs. Compared to the composition of oil from the pipeline source, VHCs identified in oil from wells sampled in 2008 were 13 to 64% depleted. The magnitude of loss for the VHCs analyzed was toluene ≫ o-xylene, benzene, C 6 and C 10–12 n-alkanes > C 7 –C 9 n-alkanes > m-xylene, cyclohexane, and 1- and 2-methylnaphthalene > 1,2,4-trimethylbenzene and ethylbenzene. Other VHCs including p-xylene, 1,3,5- and 1,2,3-trimethylbenzenes, the tetramethylbenzenes, methyl- and ethyl-cyclohexane, and naphthalene were not depleted during the time of the study. Water–oil and air–water batch equilibration simulations indicate that volatilization and biodegradation is most important for the C 6 –C 9 n-alkanes and cyclohexanes; dissolution and biodegradation is important for most of the other hydrocarbons. Depletion of the hydrocarbons in the oil pool is controlled by: the lack of oxygen and nutrients, differing rates of recharge, and the spatial distribution of oil in the aquifer. The mass loss of these VHCs in the 5 wells is between 1.6 and 7.4% in 29 years or an average annual loss of 0.06–0.26%/year. The present study shows that the composition of LNAPL changes over time and that these changes are spatially variable. This highlights the importance of characterizing the temporal and spatial variabilities of the source term in solute-transport models.

Minnesota↗

USGS2010

Vadose zone attenuation of organic compounds at a crude oil spill site - Interactions between biogeochemical reactions and multicomponent gas transport

Contaminant attenuation processes in the vadose zone of a crude oil spill site near Bemidji, MN have been simulated with a reactive transport model that includes multicomponent gas transport, solute transport, and the most relevant biogeochemical reactions. Dissolution and volatilization of oil components, their aerobic and anaerobic degradation coupled with sequential electron acceptor consumption, ingress of atmospheric O 2 , and the release of CH 4 and CO 2 from the smear zone generated by the floating oil were considered. The focus of the simulations was to assess the dynamics between biodegradation and gas transport processes in the vadose zone, to evaluate the rates and contributions of different electron accepting processes towards vadose zone natural attenuation, and to provide an estimate of the historical mass loss. Concentration distributions of reactive (O 2 , CH 4 , and CO 2 ) and non-reactive (Ar and N 2 ) gases served as key constraints for the model calibration. Simulation results confirm that as of 2007, the main degradation pathway can be attributed to methanogenic degradation of organic compounds in the smear zone and the vadose zone resulting in a contaminant plume dominated by high CH 4 concentrations. In accordance with field observations, zones of volatilization and CH 4 generation are correlated to slightly elevated total gas pressures and low partial pressures of N 2 and Ar, while zones of aerobic CH 4 oxidation are characterized by slightly reduced gas pressures and elevated concentrations of N 2 and Ar. Diffusion is the most significant transport mechanism for gases in the vadose zone; however, the simulations also indicate that, despite very small pressure gradients, advection contributes up to 15% towards the net flux of CH 4 , and to a more limited extent to O 2 ingress. Model calibration strongly suggests that transfer of biogenically generated gases from the smear zone provides a major control on vadose zone gas distributions and vadose zone carbon balance. Overall, the model was successful in capturing the complex interactions between biogeochemical reactions and multicomponent gas transport processes. However, despite employing a process-based modeling approach, honoring observed parameter ranges, and generally obtaining good agreement between field observations and model simulations, accurate quantification of natural attenuation rates remains difficult. The modeling results are affected by uncertainties regarding gas phase saturations, tortuosities, and the magnitude of CH 4 and CO 2 flux from the smear zone. These findings highlight the need to better delineate gas fluxes at the model boundaries, which will help constrain contaminant degradation rates, and ultimately source zone longevity.

Minnesota↗

USGS1998

Ground water contamination by crude oil near Bemidji, Minnesota

Ground-water contamination by crude oil, and other petroleum-based liquids, is a widespread problem. An average of 83 crude-oil spills occurred per year during 1994-96 in the United States, each spilling about 50,000 barrels of crude oil (U.S. Office of Pipeline Safety, electronic commun., 1997). An understanding of the fate of organic contaminants (such as oil and gasoline) in the subsurface is needed to design innovative and cost-effective remedial solutions at contaminated sites.

Minnesota↗

USGS1998

Spatial variation in saturated hydraulic conductivity of sediments at a crude-oil spill site near Bemidji, Minnesota

Saturated hydraulic conductivity of aquifer sediments at a crude-oil spill research site near Bemidji, Minnesota were examined using pneumatically-induced head-difference tests and packer/vacuum system tests. Results from slug tests on 58 wells show that hydraulic conductivity varies both horizontally and vertically in the range from about 10 -7 to 10 -4 meters per second (m/s), with a median of 7.28 x 10 -5 m/s. Hydraulic conductivities of the well-sorted medium to fine sand facies, which contains a majority of the oil plume, range from 1.76 x 10 -5 to 9.82 x 10 -5 m/s with a median of 5.42 x 10 -5 m/s. Hydraulic conductivities of the lower sand and gravel unit, which contains a majority of the plume of dissolved petroleum constituents, range from 4.42 x 10 -6 to 5.36 x 10 -4 m/s with a median of 2.32 x 10 -4 m/s. The average linear velocity of ground water near the spill site was calculated to examine the effects of advective flow on migration of the plumes of oil and dissolved petroleum constituents. The average linear velocity in the well-sorted medium to fine sand facies during September 1996 was about 11 meters per year (m/year). If we assume that this was the average velocity during the 17-year period since the spill (1979-96), total advective flow of ground water in this facies was about 187 m. During this 17-year period, oil floating on the water table migrated only about 40 m. By comparison, the lower sand and gravel unit had an average linear velocity of about 29 m/year, or about 3 times greater than the velocity in the well-sorted medium to fine sand facies. Based on a 29 m/year velocity, advective flow of ground water in this unit during the 17-year period since the spill was about 493 m; whereas, the plume of dissolved petroleum constituents migrated only about 200 m. These results indicate that spatial variability of hydraulic conductivity and ground-water velocity at the research site likely is a factor affecting the rate of contaminant migration. Additional research is needed to fully evaluate how the contaminant plumes are affected by changes in hydraulic properties of the various lithologic units.

Minnesota↗

USGS1990

Transformation of Monoaromatic hydrocarbons to organic acids in anoxic groundwater environment

The transformation of benzene and a series of alkylbenzenes was studied in anoxic groundwater of a shallow glacial-outwash aquifer near Bemidji, Minnesota, U.S.A. Monoaromatic hydrocarbons, the most water-soluble components of crude oil, were transported downgradient of an oil spill, forming a plume of contaminated groundwater. Organic acids that were not original components of the oil were identified in the anoxic groundwater. The highest concentrations of these oxidized organic compounds were found in the anoxic plume where a decrease in concentrations of structurally related alkylbenzenes was observed. These results suggest that biological transformation of benzene and alkylbenzenes to organic acid intermediates may be an important attenuation process in anoxic environments. The transformation of a complex mixture of hydrocarbons to a series of corresponding oxidation products in an anoxic subsurface environment provides new insight into in situ anaerobic degradation processes.

Minnesota↗

USGS1987

Movement and fate of crude-oil in contaminants in the subsurface environment at Bemidji, Minnesota: Chapter C in U.S. Geological Survey program on toxic waste--ground-water contamination: Proceedings of the Third technical meeting, Pensacola, Florida, March 23-27, 1987

On August 20, 1979, a pipeline break in a remote area near Bemidji, Minn. (fig. C-l), resulted in the release of 1.5x10 5 L (liters) of crude oil. Although about 1.1x10 5 L were removed from the site as part of the cleanup, some crude oil infiltrated the ground and percolated to the water table. The spill occurred in the recharge area of a local flow system that discharges to a small lake 300 m (meters) downgradient (Hult, 1984). The aquifer is a pitted and dissected outwash plain underlain at a depth of about 20 m by low-permeability till. Crude oil is floating on the water table about 8 m below land surface and has migrated about 20 m as a separate fluid phase. Soluble petroleum derivatives have dissolved in and are moving with ground water. Volatile constituents are migrating through the unsaturated zone by diffusion. The abstracts presented in this chapter provide an overview of ongoing efforts to combine the results of interdependent, interdisciplinary research into the comprehensive understanding of the physical, chemical, and biological processes that will be needed to develop predictive models of contaminant mobilization, transport, and fate. Franzi investigates the relationship between depositional and post-depositional processes and the heterogeneity and anisotropy of the aquifer. Post-depositional subsidence and collapse caused by melting of stagnant ice has created significant geomorphic and hydrogeologic structures. Miller describes a preliminary ground-water flow and chemical-transport model used to assess the effect of these hydrologic discontinuities, estimate aquifer properties, and to guide continuing field work. Abstracts by Siegel, Bennett, and Berndt describe studies of dissolved inorganic constituents and parameters done to characterize the geochemical environments in and around the site. An anoxic zone, probably plume shaped, extends downgradient of the oil pool and into an oxic zone that surrounds the contamination. Carbonate minerals are actively dissolving in the oxic spray zone upgradient of the oil pool where oil is being mineralized, whereas quartz is dissolving underneath the oil by organic-acid complexation. Selective leaching experiments show that fractionation of metals is also occurring where the aquifer matrix is contaminated. Morphological analysis of quartz sand grains clearly show unusual rock-water interactions are occurring in the anaerobic contaminant zone. Preliminary analysis indicates the possibility of an organic/quartz interaction that is significantly increasing the mobility of silica through the system. Predictions of the evolution and ultimate geometry of contaminant plumes resulting from spills require quantitative descriptions of the rate of mass transfer from the organic fluid to ground water. Pfannkuch presents laboratory and field work that describe how the the rate of oil dissolution, and therefore the strength of the contaminant source, is controlled by fluctuations in ground-water velocity and water-table fluctuations.

Minnesota↗

USGS1984

Ground-water contamination by crude oil at the Bemidji, Minnesota, research site- An introduction: Chapter A in Ground-water contamination by crude oil at the Bemidji, Minnesota, research site; US Geological Survey Toxic Waste--ground-water contamination study

The U.S. Geological Survey has begun a research project to improve understanding of the mobilization, transport, and fate of petroleum contaminants in the shallow subsurface and to use this understanding to develop predictive models of contaminant behavior. The project site is near Bemidji in northern Minnesota where an accidental spill of 10,500 barrels of crude oil occurred when a pipeline broke on August 20, 1979. Regulatory and remedial actions have been completed. The site is in a remote area with neither man-made hydraulic stresses nor other anthropogenic sources of the compounds of interest. The spill is in the recharge area of a local flow system that discharges to a small closed lake approximately 1,000 feet down the hydraulic gradient. The aquifer is pitted outwash dissected by younger glacial channels and is underlain by poorly permeable till at a depth of about 80 feet. Ground water dissolves oil floating on the water table under the spill site and moves toward the lake. At the water table, ground water enters the lake through lacustrine sediments; at depth, flow may be underneath the lake through the outwash. Contaminant transport has been as rapid as 4 feet per day based on the rate of movement of contaminants monitored through wells installed within a few days of the spill, but average rates are undoubtedly much less.

Minnesota↗