Geology topics

Groundwater & aquifers

Find USGS groundwater and aquifer publications. Search an aquifer name or place, compare source-supplied dates and open reports for hydrogeology, recharge and water-level studies.

Follow this topic with RSS

351 records · Page 8Linked to original sources

USGS2025

Factors affecting the distribution of water-bearing fractures in the bedrock aquifers of West Virginia

Bedrock aquifers cover 23,601 square miles within the State of West Virginia and comprise 97.4 percent of the surficial area within the State; the remaining 2.6 percent (621 square miles) consists of alluvial sand-and-gravel and glacial outwash aquifers bordering the State’s major rivers. While West Virginia’s alluvial aquifers have been studied extensively, bedrock aquifers have only been characterized for studies completed in a few areas in Jefferson, McDowell, and Monroe Counties. Bedrock aquifers are water supplies for public supply, agriculture, industry, and residential homeowner use. In this study, the U.S. Geological Survey, in cooperation with the West Virginia Department of Environmental Protection Division of Water and Waste Management, provides a statewide assessment of the occurrence and distribution of fractures within bedrock aquifers of the State and the various topographic, physiographic, and lithologic influences controlling the occurrence and distribution of bedrock fractures. The results of this study provide an increased understanding of the distribution of fractures in bedrock aquifers in West Virginia and help to verify trends that have been suspected for many years but were never well documented or verified by data. The results confirmed that the density of fractures and those that were determined to be water bearing decrease significantly with depth. A statistically significant difference in the density of fractures was observed at a depth of 215 feet for wells in the Appalachian Plateaus Physiographic Province’s and in the Valley and Ridge Physiographic Province’s aquifers; a higher density of fractures and water-bearing fractures were above a depth of 215 feet than below that depth. This is an important consideration when drilling wells for residential, commercial, industrial, or agricultural water supply. Abandoned underground coal mines are commonly believed to form large pools of water in the interconnected mine entries in abandoned room and pillar coal mines. Such pools of water can and do exist in abandoned underground coal mines, but many mines lack open entries and are held up by overburden strata and pillars that can collapse and form aquifers comprised of vast interconnected rubble zones (gob), especially in older mines. Data assessed for this study showed that shale-corrected values of effective porosity for limestone aquifers in West Virginia had a median value of 2 percent and an average value of 4 percent and generally are mineralized with low effective porosity. Argillaceous or sandy limestone has a median shale-corrected porosity of 4 percent and an average shale-corrected porosity of 5 percent. The median and average shale-corrected porosity of sandstone aquifers was estimated to be 14 percent, but the median shale-corrected porosity for argillaceous or calcareous sandstone was 5 percent and the average shale-corrected porosity for argillaceous or calcareous sandstone was 6 percent. Even though shale has a relatively high total sonic porosity compared to other lithologies, shale and siltstone had relatively low shale-corrected porosity, ranging from 0 to 2 percent. Well yields were previously documented to be highest in valley settings, lowest on hilltops, and intermediate on hillsides. Transmissivity data provided by this study confirm this general pattern within the Appalachian Plateaus Province; however, the Valley and Ridge Province does not follow this pattern. While still lowest on hilltop settings, the highest well yields were in hillside settings. The trend for the Valley and Ridge Province was likely skewed because of 9 high-yield wells specifically targeting deeper thin limestone units, such as the Tonoloway and Helderberg Limestones, at depths with transmissivity in excess of 2,000 feet squared per day in Mineral County, West Virginia, or targeting karst aquifers in Berkeley, Jefferson, or Greenbrier Counties, West Virginia. Finally, water-bearing fractures have been hypothesized to comprise a small number of all fractures within a typical bedrock well in West Virginia. Data collected for this study support this theory. A total of 3,403 fractures were identified during this study; 3,151 (92.6 percent) of those fractures are low-transmissive, and only 252 (7.4 percent) fractures are water-bearing. Even though a well may contain many fractures, less than 8 percent are considered water-bearing fractures.

West Virginia↗

USGS1998

Ground-water flow in the surficial aquifer system and potential movement of contaminants from selected waste-disposal sites at Naval Station Mayport, Florida

Ground-water flow through the surficial aquifer system at Naval Station Mayport near Jacksonville, Florida, was simulated with a two-layer finite-difference model as part of an investigation conducted by the U.S. Geological Survey. The model was calibrated to 229 water-level measurements from 181 wells during three synoptic surveys (July 17, 1995; July 31, 1996; and October 24, 1996). A quantifiable understanding of ground-water flow through the surficial aquifer was needed to evaluate remedial-action alternatives under consideration by the Naval Station Mayport to control the possible movement of contaminants from sites on the station. Multi-well aquifer tests, single-well tests, and slug tests were conducted to estimate the hydraulic properties of the surficial aquifer system, which was divided into three geohydrologic unitsï¿½an S-zone and an I-zone separated by a marsh-muck confining unit. The recharge rate was estimated to range from 4 to 15 inches per year (95 percent confidence limits), based on a chloride-ratio method. Most of the simulations following model calibration were based on a recharge rate of 8 inches per year to unirrigated pervious areas. The advective displacement of saline pore water during the last 200 years was simulated using a particle-tracking routine, MODPATH, applied to calibrated steady-state and transient models of the Mayport peninsula. The surficial aquifer system at Naval Station Mayport has been modified greatly by natural and anthropogenic forces so that the freshwater flow system is expanding and saltwater is being flushed from the system. A new MODFLOW package (VAR1) was written to simulate the temporal variation of hydraulic properties caused by construction activities at Naval Station Mayport. The transiently simulated saltwater distribution after 200 years of displacement described the chloride distribution in the I-zone (determined from measurements made during 1993 and 1996) better than the steady-state simulation. The advective movement of contaminants from selected sites within the solid waste management units to discharge points was simulated using MODPATH. Most of the particles were discharged to the nearest surface-water feature after traveling less than 1,000 feet in the ground-water system. Most areas within 1,000 feet of a surface-water feature or storm sewer had traveltimes of less than 50 years, based on an effective porosity of 40 percent. Contributing areas, traveltimes, and pathlines were identified for 224 wells at Naval Station Mayport under steady-state and transient conditions by back-tracking a particle from the midpoint of the wetted screen of each well. Traveltimes to contributing areas that ranged between 15 and 50 years, estimated by the steady-state model, differed most from the transient traveltime estimates. Estimates of traveltimes and pathlines based on steady-state model results typically were 10 to 20 years more and about twice as long as corresponding estimates from the transient model. The models differed because the steady-state model simulated 1996 conditions when Naval Station Mayport had more impervious surfaces than at any earlier time. The expansion of the impervious surfaces increased the average distance between contributing areas and observation wells.

Florida↗

USGS2026

Hydrologic investigation of water level fluctuations at Moreau Lake, Moreau Lake State Park, town of Moreau, New York

The causes of water level fluctuations at Moreau Lake, within Moreau Lake State Park in the town of Moreau, New York, were investigated from 2016 to 2021 after lake water levels dropped between 2015 and 2016, raising concerns about the loss of a shallow swimming area at the park beach. Annual variation in precipitation records from the area did not account for the lake water level decline. Two possible causes for the low lake water levels were investigated: the increase in groundwater withdrawals from new residential development since about 2000 and seasonal changes (nongrowing and growing seasons) in precipitation. Investigation of the potential effects of nearby groundwater withdrawals required the compilation and collection of well-log data, seismic surveys, and measurements of lake and groundwater levels, field chemical parameters, and water isotopes to define the hydrogeologic system and to estimate water use. The net result of this work was the determination that Moreau Lake is a “flow though” lake with no surface water outlet; groundwater enters the lake on the upgradient side and exits through the downgradient side, however, groundwater does not flow southward from the lake toward nearby groundwater withdrawals from the semiconfined aquifer, and thus groundwater withdrawals were unlikely to have an effect on lake water levels. Investigation of the historic precipitation records during nongrowing (November through April) and growing (May through October) indicated that (1) nongrowing season precipitation from 2011–12 to 2015–16 was more deficient than any similar period during the past 78 years and (2) since about 2000, nongrowing seasons have been drier overall and growing seasons have been considerably wetter. Initiation of lake water level monitoring in 2016 provided an opportunity to compare seasonal precipitation with seasonal lake water level changes. Nongrowing season lake water levels are very sensitive to precipitation, such that high precipitation (40 percent above the seasonal median) resulted in a 5-foot rise in lake water level. In contrast, the growing season lake water levels are sensitive to dry conditions; for example, deficient rainfall (about 6 percent below the seasonal median) resulted in a decline of lake water levels of about 3.5 feet. However, lake water levels are insensitive to high growing season rainfall inputs (about 10 to 47 percent above the seasonal median); lake water levels consistently declined about by 0.8 feet above this range of seasonal excessive precipitation.

New York↗

USGS2026

Geologic framework, hydrostratigraphy, and ichnology of the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles, Blanco, Comal, Hays, and Kendall Counties, Texas

During 2023, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, revised an initial characterization completed during 2015–16 of the geologic framework, hydrostratigraphy, and ichnology of the Edwards and Trinity aquifers in the Blanco, Payton, and Rough Hollow 7.5-minute quadrangles in Blanco, Comal, Hays, and Kendall Counties, Texas. The purpose of this report is to present the updated geologic framework, hydrostratigraphy, and ichnology of the Trinity and Edwards Groups in those quadrangles. Rocks exposed in the study area are of the Lower Cretaceous Trinity Group and lower part of the Fort Terrett Formation of the Lower Cretaceous Edwards Group. The faulting and fracturing in the study area are part of the Balcones Fault Zone, an extensional system of faults active during the Paleocene to middle Eocene that generally trends southwest to northeast in south-central Texas. Hydrostratigraphically, the rocks exposed in the study area contain a section of the Edwards (Balcones Fault Zone) aquifer, upper zone of the Trinity aquifer, and middle zone of the Trinity aquifer. In the study area, the only hydrostratigraphic units of the Edwards (Balcones Fault Zone) aquifer remaining are (from top to bottom) VII and VIII, which cap several hills. The mapped hydrostratigraphic units of the upper zone of the Trinity aquifer are (from top to bottom) the cavernous, Camp Bullis, upper evaporite, fossiliferous, and lower evaporite. The mapped hydrostratigraphic units of the middle zone of the Trinity aquifer are (from top to bottom) the Bulverde, Little Blanco, Twin Sisters, Doeppenschmidt, Herff Falls (where present), Rust, Honey Creek, Hensell, and Cow Creek hydrostratigraphic units.

Texas↗

USGS1997

Integrity of production wells and confining unit at the Naval Weapons Industrial Reserve Plant, Dallas, Texas, 1995

Ground water in the shallow alluvial aquifer is contaminated at the Naval Weapons Industrial Reserve Plant, Dallas, Texas. Five production wells at the site are cased through the alluvial aquifer and underlying units and are screened in either the Paluxy or Twin Mountains aquifers. Three abandoned wells, originally completed in the Twin Mountains aquifer but filled with drilling mud in 1958, also penetrate the alluvial aquifer. The Paluxy and Twin Mountains aquifers are used for drinking-water supplies in and around the Dallas-Fort Worth metroplex. Trichloroethylene and its degradation products, dichloroethylene and vinyl chloride, and the metal chromium previously have been detected in the shallow alluvial aquifer. Current (1995) analyses of water-quality samples taken from the static water column of the five production wells and one of the abandoned wells indicate no trichloroethylene, dichloroethylene, or vinyl chloride in the water column of these wells. Chromium was detected in all samples, but concentrations were less than the practical quantitation limit, which is the regulatory action level for this site. The results of borehole geophysical log analysis indicate that two of the production wells could have vertically connected intervals where cement bonding in the well annulus is poor. The other production wells have overall good bonding. Temperature logs do not indicate flow behind casing except in the screened interval of one well. Geophysical logs show the Eagle Ford Shale ranges from 147 to 185 feet thick at the site. The Eagle Ford Shale has low permeability and a high plasticity index. These physical characteristics make the Eagle Ford Shale an excellent confining unit.

Texas↗

USGS2025

Land-based nutrient flux to a fringing reef: Insights from Ofu Island, American Samoa

Submarine groundwater discharge (SGD) is a critical driver of nutrient transport in coral reef ecosystems, shaping water quality, primary productivity, and overall reef health. This study quantifies SGD fluxes and associated nutrient dynamics in two reef flat pools within the Ofu Unit of the National Park of American Samoa: Papaloloa and Fatuana. A multi-method approach integrating unoccupied aerial system-based thermal infrared (UAS-TIR) surveys, radon-based SGD measurements, multichannel electrical resistivity tomography (ERT), and discrete water sampling was used to assess SGD rates and nutrient contributions. UAS-TIR imagery revealed cooler sea surface temperatures in both pools, indicative of SGD, with the higher fluxes observed in Papaloloa. Radon measurements revealed a strong inverse correlation between SGD rates and tidal stage, with a more immediate SGD response at Papaloloa due to its highly permeable calcareous sand and gravel substrate. In contrast, a 2–3-hour lag in SGD response at Fatuana suggests discharge from a more inland aquifer that has lower diffusivity. Nutrient concentrations correlated with temperature and salinity, confirming SGD as the dominant nutrient transport mechanism, whereas isotopic analyses indicated inputs from both groundwater and potential anthropogenic sources. Despite lower SGD flux at Fatuana, higher algal cover suggests additional factors influencing algal proliferation, including substrate availability and hydrodynamic conditions. Excess nutrient inputs from SGD may contribute to algal overgrowth, which threatens Ofu’s thermally tolerant corals by increasing competition for space and light. These findings underscore the complexity of SGD-mediated nutrient dynamics in reef environments and emphasize the need for integrated hydrological and ecological assessments to support effective reef conservation and management strategies.

American Samoa, Ofu Island, Olosega Island↗

USGS2025

Total uncertainty quantification in inverse solutions with deep learning surrogate models

We propose an approximate Bayesian method for quantifying the total uncertainty in inverse partial differential equation (PDE) solutions obtained with machine learning surrogate models, including operator learning models. The proposed method accounts for uncertainty in the observations, PDE, and surrogate models. First, we use the surrogate model to formulate a minimization problem in the reduced space for the maximum a posteriori (MAP) inverse solution. Then, we randomize the MAP objective function and obtain samples of the posterior distribution by minimizing different realizations of the objective function. We test the proposed framework by comparing it with the iterative ensemble smoother and deep ensembling methods for a nonlinear diffusion equation with an unknown space-dependent diffusion coefficient. Among other applications, this equation describes the flow of groundwater in an unconfined aquifer. Depending on the training dataset and ensemble sizes, the proposed method provides similar or more descriptive posteriors of the parameters and states than the iterative ensemble smoother method. Deep ensembling underestimates uncertainty and provides less-informative posteriors than the other two methods. Our results show that, despite inherent uncertainty, surrogate models can be used for parameter and state estimation as an alternative to the inverse methods relying on (more accurate) numerical PDE solvers.

Journal of Computational Physics↗

USGS2025

Salinas Valley integrated hydrologic and reservoir operations models, Monterey and San Luis Obispo Counties, California

The area surrounding the Salinas Valley groundwater basin in Monterey and San Luis Obispo Counties of California is a highly productive agricultural area, contributes significantly to the local economy, and provides a substantial portion of vegetables and other agricultural commodities to the Nation. This region of California provides about half of the Nation’s lettuce, celery, broccoli, and spinach each year. Thus, this agricultural area provides significant volumes of agricultural products not just for California but the entire United States. Changes in population and increased agricultural development, which includes a shift toward more water-intensive crops, and climate variability, have put increasing demand on both surface water and groundwater resources in the valley. This has resulted in water management challenges in the Salinas Valley that are predominantly related to distribution of water supply throughout the basin. Where and when the water is present in the surface and subsurface does not coincide with where and when the water is needed. To deal with the distribution issue, historically water has been used conjunctively in the valley. Conjunctive use is a water management strategy that coordinates surface water and groundwater use to maximize water availability. Groundwater is used throughout the Salinas Valley to meet water demands when surface water supplies are insufficient. Availability of surface water is constrained by climate. Precipitation and streamflow vary seasonally and year to year. Although there are two reservoirs in the Salinas Valley to capture and store water during wet periods, the only conveyance of reservoir water to coastal agricultural areas is the Salinas River. Increasing demand on groundwater and surface water resources throughout the Salinas Valley has resulted in undesirable effects of unsustainable water use, such as surface water depletion, groundwater level declines, storage depletion in the principal aquifers, and seawater intrusion. To address these escalating issues, local communities, water management agencies, and groundwater sustainability agencies are evaluating how to sustainably manage both their surface water and groundwater resources. To meet water demands and reduce undesirable effects of unsustainable water use, continued conjunctive management of surface water and groundwater would ideally incorporate strategies to deal with increases in demand and a variable climate. To evaluate the challenging water management issues in the Salinas Valley, the U.S. Geological Survey, Monterey County Water Resource Agency, and the Salinas Valley Basin Groundwater Sustainability Agency developed a comprehensive suite of models that represent the Salinas Valley Hydrogeologic system called the Salinas Valley System Model. The Salinas Valley Geologic Framework was developed to characterize the subsurface using various topographic and geologic data sources, including information on hydrogeologic units, their surfaces and extents, geologic structures, lithology, and elevations from borehole data and cross sections, as well as details on faults and existing models. The Salinas Valley Watershed Model simulates the entire Salinas River watershed. Monthly surface water inflows into the integrated hydrologic model domain were simulated using the Salinas Valley Watershed Model. The historical model uses historical climate data, water and land use data, and reservoir releases to simulate agricultural operations, including landscape water demands, diversions, and reclaimed wastewater. The operational model adds an embedded reservoir operations framework to the simulation of the historical model that allows specified operational rules to simulate reservoir releases and changes in reservoir storage. The operational model assumes current reservoir operations and constant land use, which differs from historical conditions. Thus, the operational model is a hypothetical baseline model that can be used by local water managers to evaluate and quantify potential benefits of water supply projects. Together, the geologic framework, watershed, historical, and operational models form a tool that can be used to simulate irrigated agriculture and associated reservoir operations of the integrated hydrologic system of the Salinas Valley.

EarthArXiv↗

USGS2024

Hydrologic investigations and a preliminary conceptual model of the groundwater system at North Penn Area 1 Superfund Site, Souderton, Montgomery County, Pennsylvania

The U.S. Geological Survey (USGS) conducted hydrogeologic investigations, reviewed existing data, and developed a preliminary conceptual model of the groundwater system as part of technical support of the U.S. Environmental Protection Agency (EPA) at the North Penn Area 1 Superfund Site (hereafter, the NP1 Site) located within the Borough of Souderton in Montgomery County, Pennsylvania. Field work and monitoring took place during 2012–18. The area is underlain by sedimentary formations that form a fractured-rock aquifer used for drinking water and industrial supply. The EPA placed the Site on the National Priorities List in 1989, identifying tetrachloroethylene (PCE) and trichloroethylene (TCE) as contaminants of concern. During 2012–18, the USGS conducted field activities that included drilling an 82-foot (ft)-deep monitoring well (MG 2220) in 2016, reconstructing a 208-ft-deep former industrial production well (MG 668 [Granite Knitting Mill]), and collecting borehole geophysical and video logs and water levels from those and five additional wells, which ranged in depth from about 50 to 200 ft below land surface. Continuous water levels were collected during 2014–17, and a synoptic set of water levels were measured in April 2018 in the seven wells. The borehole geophysical logs (caliper, acoustic televiewer, natural gamma, single-point resistance, vertical flow, and fluid temperature and resistivity) and borehole video logs in the seven wells were evaluated to assess potential for lithologic correlation and to identify and describe water-bearing features, which included both low- and high-angle fractures and other openings oriented along dipping bedding planes, joints, or possible faults. Borehole geophysical logs collected by USGS in 1992 in a 300-ft-deep former production well near the Site were also evaluated. Few to no distinctive features were identified on geophysical logs (natural gamma and single-point resistance) that could be used for correlation, thus limiting this approach to determining local geologic structure. Extensive fracturing in the upper 62 ft of monitoring well MG 2220 indicates that the well was likely drilled through a zone of faulting, and other evidence of faulting is present in the area near the Site. Assessment of continuous water levels showed hydraulic connections among some wells as indicated by rising or falling water levels in response to changes in pumping rates at nearby wells. A map of water levels measured in April 2018 indicates potential for groundwater flow generally toward the stream to the south and southwest of the Site, but the limited water-level data are insufficient to describe vertical groundwater gradients or lateral gradients in any detail. Review of 1999–2022 volatile organic compound (VOC) monitoring data collected by the Pennsylvania Department of Environmental Protection for five monitoring wells indicates that the highest groundwater concentrations of PCE and TCE were found in samples from extraction well MG 2201 (S-1) downgradient from, and nearest to, the previously identified Site contaminant source area, and these concentrations fluctuated through time. PCE concentrations were higher than TCE concentrations in samples from all five monitoring wells and were much higher than TCE concentrations in samples from extraction well MG 2201 (S-1). Temporally variable recharge is a possible factor affecting observed fluctuations in PCE concentrations in groundwater samples from well extraction MG 2201 (S-1), as indicated by a general inverse relation between PCE concentrations and water levels in a nearby long-term observation well. The PCE concentration of 1,830 micrograms per liter (μg/L) in a May 2018 water sample from monitoring well MG 2220 was more than four times the PCE concentration of 444 μg/L in a December 2017 sample from the nearby extraction well MG 2201 (S-1), which is open to fewer fractures. Low concentrations of VOCs were measured in surface water at two stream sites downgradient from wells with the highest groundwater VOC concentrations at the Site, indicating that discharge of contaminated groundwater to the stream is likely. Development of a conceptual model of the groundwater system was constrained by limited data. In areas with no pumping, groundwater-flow directions generally are thought to be controlled by topography and geologic structure (bedding orientation) and likely to the south and southwest of the Site, with local flow directions affected by orientations of fractures, joints, and local faults. Additional investigations that could help improve the conceptual model of the groundwater system and help delineate the extent of groundwater contamination and its transport are discussed.

Pennsylvania↗

USGS2026

Salinas Valley integrated hydrologic and reservoir operations models, Monterey and San Luis Obispo Counties, California

The area surrounding the Salinas Valley groundwater basin in Monterey and San Luis Obispo Counties of California is a highly productive agricultural area, contributes substantially to the local economy, and provides a substantial portion of vegetables and other agricultural commodities to the Nation. This region of California provides about half of the Nation’s lettuce, celery, broccoli, and spinach each year. Thus, this agricultural area provides substantial volumes of agricultural products not just for California but for the United States. Changes in population and increased agricultural development, which includes a shift toward more water-intensive crops, and climate variability, have put increasing demand on both surface-water and groundwater resources in the valley. This situation has resulted in water management challenges in the Salinas Valley that generally relate to the distribution of the water supply throughout the basin. Where and when the water is present in the surface and subsurface does not coincide with where and when the water is needed. Historically, to deal with the distribution issue, water has been used conjunctively in the valley. Conjunctive use is a water management strategy that coordinates surface-water and groundwater use to maximize water availability. Groundwater is used throughout the Salinas Valley to meet water demands when surface-water supplies are insufficient. The availability of surface water is constrained by climate. Precipitation and streamflow vary seasonally and year to year. Although there are two reservoirs in the Salinas Valley to capture and store water during wet periods, the only conveyance of reservoir water to coastal agricultural areas is the Salinas River. Increasing demand for groundwater and surface-water resources throughout the Salinas Valley has resulted in undesirable effects from unsustainable water use, such as surface-water depletion, groundwater-level declines, storage depletion in the principal aquifers, and seawater intrusion. To address these escalating issues, local communities, water management agencies, and groundwater sustainability agencies are evaluating how to sustainably manage both their surface-water and groundwater resources. To meet water demands and reduce the undesirable effects of unsustainable water use, continued conjunctive management of surface water and groundwater would ideally incorporate strategies to deal with increases in demand and climate variability. To evaluate the challenging water management issues in the Salinas Valley, the U.S. Geological Survey, Monterey County Water Resources Agency, and the Salinas Valley Basin Groundwater Sustainability Agency developed a comprehensive suite of models that represent the Salinas Valley hydrogeologic system called the Salinas Valley System Model. The geologic framework is known as the Salinas Valley Geologic Framework and was developed to characterize the subsurface using various topographic and geologic data sources, including information on hydrogeologic units, their surfaces and extents, geologic structures, lithology, and elevations from borehole data and cross sections, as well as details on faults and existing models. The surface-water model is called the Salinas Valley Watershed Model and simulates the Salinas River watershed. Monthly surface-water inflows into the integrated hydrologic model domain were simulated using the Salinas Valley Watershed Model. The historical model uses historical climate data, water and land use data, and reservoir releases to simulate agricultural operations, including landscape water demands, diversions, and reclaimed wastewater. The operational model adds an embedded reservoir operations framework to the simulation of the historical model that allows specified operational rules to simulate reservoir releases and changes in reservoir storage. The operational model assumes current reservoir operations and constant land use, which differs from historical conditions. Thus, the operational model is a hypothetical baseline model that can be used by local water managers to evaluate and quantify potential benefits of water supply projects. Together, the geologic framework, watershed, historical, and operational models form a tool that can be used to simulate irrigated agriculture and associated reservoir operations of the integrated hydrologic system of the Salinas Valley.

California↗

USGS2025

Borehole geophysical time-series logging to monitor passive ISCO treatment of residual chlorinated-ethenes in a confining bed, NAS Pensacola, Florida

In-situ chemical oxidation (ISCO) is a common method to remediate chlorinated ethene contaminants in groundwater. Monitoring the effectiveness of ISCO can be hindered because of insufficient observations to assess oxidant delivery. Advantageously, potassium permanganate, one type of oxidant, provides the opportunity to use its strong electrical signal as a surrogate to track oxidant delivery using time-series borehole geophysical methods, like electromagnetic (EM) induction logging. Here we report a passive ISCO (P-ISCO) experiment, using potassium permanganate cylinders emplaced in boreholes, at a chlorinated ethene contamination site, Naval Air Station Pensacola, Florida. The contaminants are found primarily at the base of a shallow sandy aquifer in contact with an underlying silty-clay confining bed. We used results of the time-series borehole logging collected between 2017 and 2022 in 4 monitoring wells to track oxidant delivery. The EM-induction logs from the monitoring wells showed an increase in EM response primarily along the contact, likely from pooling of the oxidant, during P-ISCO treatment in 2021. Interestingly, concurrent natural gamma-ray (NGR) logging showed a decrease in NGR response at 3 of the 4 wells possibly from the formation of manganese precipitates coating sediments. The coupling of time-series logging and well-chemistry data allowed for an improved assessment of passive ISCO treatment effectiveness.

Florida↗

USGS2025

Geochemistry and Soils of the Big Smoky Valley Fens, Nevada

Fens are groundwater-fed wetlands that can provide habitat for plants and animals. Due to anthropogenic activities and climate change, many fens around the world are at risk. This paper presents the results of a study of the hydrology and geochemistry of fens in Big Smoky Valley, central Nevada to support the Bureau of Land Management’s activities in the area. A water sample from the largest fen in the study area was analyzed for its water chemistry and compared to a nearby alluvial aquifer and hot spring. The high SiO 2 concentration of the fen sample implies that the fen water may originate from geothermal water. A soil core was taken to analyze radiocarbon age and soil type. A majority of the core was composed of silt and clay interlayered with water-filled voids. Changes in the character of the clay with depth suggest that there may have been changes in the depositional environment over time. Radiocarbon dating of Ruppia seeds showed longevity of the fen, with the minimum 14 C age of the core as 4,375±40 years. This paper provides reconnaissance-level information on the Big Smoky Valley fens, but further information would be needed to better understand the source of water to the fens or how the fen environment has changed over time with climate.

Nevada↗

USGS2025

Reservoir thermal energy storage pre-assessment for the United States

Storing thermal energy underground for later use in electricity production or direct-use heating/cooling is a promising, viable, and economical green energy option. Reservoir thermal energy storage (RTES) is one such option, which stores energy in underutilized permeable strata with low ambient groundwater flow rates and more geochemically evolved (e.g. brackish/saline) waters relative to overlying principal aquifer systems. The U.S. Geological Survey has begun assessing RTES potential nationally by focusing on five generalized geologic regions (Basin and Range, Coastal Plain, Illinois Basin, Michigan Basin, Pacific Northwest) across the United States. Hydrogeologic reservoir models are developed for the following eight metropolitan area cities within those regions to evaluate RTES performance across different climates and subsurface conditions: Albuquerque, New Mexico; Charleston, South Carolina; Chicago and Decatur, Illinois; Lansing, Michigan; Memphis, Tennessee; Phoenix, Arizona; and Portland, Oregon. Evaluated metrics include estimated required well spacing, thermal storage capacity, and thermal recovery efficiency through time. Also considered for each reservoir are potential complicating factors, including reservoir depth, thermally driven free convection, and groundwater salinity. This work focuses on direct-use cooling because the need for cooling modern office buildings greatly exceeds that for heating in most parts of the country (Falta and others, 2016); however, the evaluated metrics are also relevant to heating and electricity applications. Results indicate that favorable RTES conditions exist in each region, with the Coastal Plain and Basin and Range being especially favorable for thermal storage capacity, while the Pacific Northwest and Michigan Basin excel at energy recovery for the evaluated cooling application. The results underscore the utility of developing maps of thermal storage capacity, subsurface temperature models, and volumetric estimates of thermal storage capacity to serve as key RTES resource classification standards. Overall, this pre-assessment provides a basic understanding of RTES potential in several cities and geologic regions throughout the country and will aid ongoing thermal energy storage assessment efforts.

Arizona, Illinois, Michigan, New Mexico, Oregon, S↗

USGS1999

Episodic sediment-discharge events in Cascade Springs, southern Black Hills, South Dakota

Cascade Springs is a group of artesian springs in the southern Black Hills, South Dakota, with collective flow of about 19.6 cubic feet per second. Beginning on February 28, 1992, a large discharge of red suspended sediment was observed from two of the six known discharge points. Similar events during 1906-07 and 1969 were documented by local residents and newspaper accounts. Mineralogic and grain-size analyses were performed to identify probable subsurface sources of the sediment. Geochemical modeling was performed to evaluate the geochemical evolution of water discharged from Cascade Springs. Interpretations of results provide a perspective on the role of artesian springs in the regional geohydrologic framework. X-ray diffraction mineralogic analyses of the clay fraction of the suspended sediment were compared to analyses of clay-fraction samples taken from nine geologic units at and stratigraphically below the spring-discharge points. Ongoing development of a subsurface breccia pipe(s) in the upper Minnelusa Formation and/or Opeche Shale was identified as a likely source of the suspended sediment; thus, exposed breccia pipes in lower Hell Canyon were examined. Upper Minnelusa Formation breccia pipes in lower Hell Canyon occur in clusters similar to the discrete discharge points of Cascade Springs. Grain-size analyses showed that breccia masses lack clay fractions and have coarser distributions than the wall rocks, which indicates that the red, fine-grained fractions have been carried out as suspended sediment. These findings support the hypothesis that many breccia pipes were formed as throats of abandoned artesian springs. Geochemical modeling was used to test whether geochemical evolution of ground water is consistent with this hypothesis. The evolution of water at Cascade Springs could not be suitably simulated using only upgradient water from the Minnelusa aquifer. A suitable model involved dissolution of anhydrite accompanied by dedolomitization in the upper Minnelusa Formation, which is caused by upward leakage of relatively fresh water from the Madison aquifer. The anhydrite dissolution and dedolomitization account for the net removal of minerals that would lead to breccia pipe formation by gravitational collapse. Breccia pipes in the lower Minnelusa Formation are uncommon; however, networks of interconnected breccia layers and breccia dikes are common. These networks, along with vertical fractures and faults, are likely pathways for transmitting upward leakage from the Madison aquifer. It is concluded that suspended sediment discharged at Cascade Springs probably results from episodic collapse brecciation that is caused by subsurface dissolution of anhydrite beds and cements of the upper Minnelusa Formation, accompanied by replacement of dolomite by calcite. It is further concluded that many breccia pipes probably are the throats of artesian springs that have been abandoned and exposed by erosion. The locations of artesian spring-discharge points probably have been shifting outwards from the center of the Black Hills uplift, essentially keeping pace with regional erosion over geologic time. Thus, artesian springflow probably is a factor in controlling water levels in the Madison and Minnelusa aquifers, with hydraulic head declining over geologic time, in response to development of new discharge points. Development of breccia pipes as throats of artesian springs would greatly enhance vertical hydraulic conductivity in the immediate vicinity of spring-discharge points. Horizontal hydraulic conductivity in the Minnelusa Formation also may be enhanced by dissolution processes related to upward leakage from the Madison aquifer. Potential processes could include dissolution resulting from leakage in the vicinity of breccia pipes that are abandoned spring throats, active spring discharge, development of subsurface breccias with no visible surface expression or spring discharge, as well as general areal leakage from the Madison aquifer into the Minnelusa Formation.

South Dakota↗

USGS2000

Water quality of selected springs and public-supply wells, Pine Ridge Indian Reservation, South Dakota, 1992-97

This report presents results of a water-quality study for the Pine Ridge Indian Reservation, South Dakota. The study was a cooperative effort between the U.S. Geological Survey and the Water Resources Department of the Oglala Sioux Tribe. Discharge and water-quality data were collected during 1992-97 for 14 contact springs located in the northwestern part of the Reservation. Data were collected to evaluate potential alternative sources of water supply for the village of Red Shirt, which currently obtains water of marginal quality from a well completed in the Inyan Kara aquifer. During 1995-97, water-quality data also were collected for 44 public-supply wells that serve about one-half of the Reservation's population. Quality-assurance sampling was used to evaluate the precision and accuracy of environmental samples. Ten of the springs sampled contact the White River Group, and four contact the Pierre Shale. Springs contacting the White River Group range from calcium bicarbonate to sodium bicarbonate water types. Two springs contacting the Pierre Shale have water types similar to this; however, sulfate is the dominant anion for the other two springs. In general, springs contacting the White River Group are shown to have better potential as alternative sources of water supply for the village of Red Shirt than springs contacting the Pierre Shale. Nine of the springs with better water quality were sampled repeatedly; however, only minor variability in water quality was identified. Six of these nine springs, of which five contact the White River Group, probably have the best potential for use as water supplies. Discharge from any of these six springs probably would provide adequate water supply for Red Shirt during most periods, based on a limited number of discharge measurements collected. Concentrations of lead exceeded the U.S. Environmental Protection Agency (USEPA) action level of 15 µg/L for three of these six springs. Five of these six springs also had arsenic concentrations that exceeded 10 µg/L, which could be problematic if the current maximum contaminant level (MCL) is lowered. Blending of water from one or more springs with water from the existing Inyan Kara well may be an option to address concerns regarding both quantity and quality of existing and potential sources. All nine springs that were sampled for indicator bacteria had positive detections on one or more occasions during presumptive tests. Although USEPA standards for bacteria apply only to public-water supplies, local residents using spring water for domestic purposes need to be aware of the potential health risks associated with consuming untreated water. One spring contacting the White River Group and two springs contacting the Pierre Shale exceeded 15 pCi/L for gross alpha; these values do not necessarily constitute exceedances of the MCL, which excludes radioactivity contributed by uranium and radon. Additional sampling using different analysis techniques would be needed to conclusively determine if any samples exceeded this MCL. Nine springs were sampled for selected pesticides and tritium. The pesticides atrazine, carbaryl, and 2,4-D were not detected in any of the samples. The nine springs were analyzed for tritium in order to generally assess the age of the water and to determine if concentrations exceeded the MCL established for gross beta-particle activity. Tritium results indicated two springs are composed primarily of water recharged prior to atmospheric testing of nuclear bombs and two other springs have a relatively large percentage of test-era water. The remaining five springs had tritium values that indicated some percentage of test-era water; however, additional sampling would be needed to determine whether water is predominantly pre- or post-bomb age. Of the 44 public-supply wells sampled, 42 are completed in the Arikaree aquifer, one is completed in an alluvial aquifer, and one is completed in the Inyan Kara aquifer. Water from the alluvial well is a sodium bicarbonate water type, water from Arikaree aquifer ranges from calcium bicarbonate to sodium bicarbonate types, and water from the Inyan Kara well is a calcium sulfate bicarbonate type. Of the 44 wells sampled, 28 (64 percent) tested positive for indicator bacteria in presumptive tests. Because these were single samples that generally were collected upstream from chemical treatment feeders, positive detections do not necessarily constitute exceedances of drinking-water standards. A single sample from an Arikaree well exceeded the MCL for arsenic of 50 µg/L. Arsenic exceeded 10 µg/L for six additional Arikaree wells and for the alluvial well and the Inyan Kara well, which could be problematic if the current MCL is lowered. The alluvial well also exceeded the secondary maximum contaminant level (SMCL) for dissolved solids, which is non-enforceable, and the action level for lead. The Inyan Kara well exceeded the SMCL's for iron and for manganese and the MCL of 5 pCi/L for radium-226 and 228 combined. Several Arikaree wells exceeded SMCL's for either pH, sulfate, dissolved solids, iron, or manganese. One Arikaree well exceeded the MCL of 4.0 mg/L for fluoride and another exceeded the MCL of 10 mg/L for nitrite plus nitrate. Ten Arikaree wells equalled or exceeded 15 pCi/L for gross alpha; however, these values do not necessarily constitute exceedances of the MCL, which excludes radioactivity contributed by uranium and radon. Additional sampling using different analysis techniques would be needed to conclusively determine if any samples exceeded this MCL. Eight wells, all from the Arikaree aquifer, equalled or exceeded the proposed MCL of 20 µg/L for uranium and 33 wells (75 percent) equalled or exceeded one-half of the proposed MCL. Although this standard has only been proposed, additional information regarding the extent of elevated uranium concentrations in the Arikaree aquifer, and the geochemical processes involved, may be beneficial. It was determined from analyses of uranium isotope data for five wells that the source of elevated uranium concentrations is naturally occurring, rather than anthropogenic.

South Dakota↗

USGS1997

Water-quality assessment of south-central Texas: Occurrence and distribution of volatile organic compounds in surface water and ground water, 1983-94, and implications for future monitoring

The study area of the South-Central Texas study unit of the National Water-Quality Assessment Program comprises the Edwards aquifer in the San Antonio region and its catchment area. The first phase of the assessment includes evaluation of existing water-quality data for surface water and ground water, including volatile organic compounds, to determine the scope of planned monitoring. Most analyses of volatile organic compounds in surface water are from the National Pollutant Discharge Elimination System sites in San Antonio, Texas. Nine volatile organic compounds were detected at the six sites. The three compounds with the most detections at National Pollutant Discharge Elimination System sites are 1,2,4-trimethylbenzene, toluene, and xylene. Analysis of volatile organic compounds in ground water was limited to Edwards aquifer wells. Twenty-eight volatile organic compounds were detected in samples from 89 wells. The five most commonly detected compounds in samples from wells, in descending order, are tetrachloroethene, trichloroethene, bromoform, chloroform, and dibromochloromethane. Detections of volatile organic compounds in surface water and ground water within the South-Central Texas study area are limited to site-specific sources associated with development; therefore, planned monitoring for possible detections of volatile organic compounds as part of the National Water-Quality Assessment Program will emphasize areas of expanding population and development. Monitoring of volatile organic compounds is planned at National Pollutant Discharge Elimination System sites, at basic fixed surface-water sites, and in the ground-water study-unit surveys.

Texas↗

USGS1998

Assessment of the hydraulic connection between ground water and the Peace River, west-central Florida

The hydraulic connection between the Peace River and the underlying aquifers along the length of the Peace River from Bartow to Arcadia was assessed to evaluate flow exchanges between these hydrologic systems. Methods included an evaluation of hydrologic and geologic records and seismic-reflection profiles, seepage investigations, and thermal infrared imagery interpretation. Along the upper Peace River, a progressive long-term decline in streamflow has occurred since 1931 due to a lowering of the potentiometric surface of the Upper Floridan aquifer by as much as 60 feet because of intensive ground-water withdrawals for phosphate mining and agriculture. Another effect from lowering the potentiometric surface has been the cessation of flow at several springs located near and within the Peace River channel, including Kissengen Spring, that once averaged a flow of about 19 million gallons a day. The lowering of ground-water head resulted in flow reversals at locations where streamflow enters sinkholes along the streambed and floodplain. Hydrogeologic conditions along the Peace River vary from Bartow to Arcadia. Three distinctive hydrogeologic areas along the Peace River were delineated: (1) the upper Peace River near Bartow, where ground-water recharge occurs; (2) the middle Peace River near Bowling Green, where reversals of hydraulic gradients occur; and (3) the lower Peace River near Arcadia, where ground-water discharge occurs. Seismic-reflection data were used to identify geologic features that could serve as potential conduits for surface-water and ground-water exchange. Depending on the hydrologic regime, this exchange could be recharge of surface water into the aquifer system or discharge of ground water into the stream channel. Geologic features that would provide pathways for water movement were identified in the seismic record; they varied from buried irregular surfaces to large-scale subsidence flexures and vertical fractures or enlarged solution conduits. Generally, the upper Peace River is characterized by a shallow, buried irregular top of rock, numerous observed sinkholes, and subsidence depressions. The downward head gradient provides potential for the Peace River to lose water to the ground-water system. Along the middle Peace River area, head gradients alternate between downward and upward, creating both recharging and discharging ground-water conditions. Seismic records show that buried, laterally continuous reflectors in the lower Peace River pinch out in the middle Peace River streambed. Small springs have been observed along the streambed where these units pinch out. This area corresponds to the region where highest ground-water seepage volumes were measured during this study. Further south, along the lower Peace River, upward head gradients provide conditions for ground-water discharge into the Peace River. Generally, confinement between the surficial aquifer and the confined ground-water systems in this area is better than to the north. However, localized avenues for surface-water and ground-water interactions may exist along discontinuities observed in seismic reflectors associated with large-scale flexures or subsidence features. Ground-water seepage gains or losses along the Peace River were quantified by making three seepage runs during periods of: (1) low base flow, (2) high base flow, and (3) high flow. Low and high base-flow seepage runs were performed along a 74-mile length of the Peace River, between Bartow and Nocatee. Maximum losses of 17.3 cubic feet per second (11.2 million gallons per day) were measured along a 3.2-mile reach of the upper Peace River. The high-flow seepage run was conducted to quantify losses in the Peace River channel and floodplain between Bartow and Fort Meade. Seepage losses calculated during high-flow along a 7.2-mile reach of the Peace River, from the Clear Springs Mine bridge to the Mobil Mine bridge, were approximately 10 percent of the river flow, or 118 cubic feet per second. Calculated seepages along the Peace River in Hardee and De Soto Counties were inconclusive, because most seepages were within the range of discharge measurement error. Two continuous aerial thermal infrared imagery surveys were conducted to locate sites of ground-water discharge along the Peace River. Although temperature and hydrologic conditions were ideal to observe spring flow using thermal infrared imaging techniques, no sources of ground-water discharge were identified using this method. Diffuse ground-water seepage may, however, provide significant ground-water discharge.

Florida↗

USGS2026

The Great Lakes Geologic Mapping Coalition—Working collaboratively to understand the geology of the Great Lakes Region

Introduction The Great Lakes Geologic Mapping Coalition (GLGMC), commonly referred to as the “Coalition,” is a partnership between the U.S. Geological Survey (USGS), the U.S. States of Illinois, Indiana, Michigan, Minnesota, New York, Ohio, Pennsylvania, and Wisconsin and the Canadian province of Ontario. The member States receive funding for geologic mapping work from the USGS National Cooperative Geologic Mapping Program (NCGMP), whereas Ontario participates as a nonfunded partner. The mission of the GLGMC is to produce three-dimensional (3D) geologic maps that depict unconsolidated sediments and near-surface bedrock in the Great Lakes region of North America. Geologic maps are the basis of most earth science investigations and help support resource exploration (energy, minerals, groundwater), natural hazard mitigation, infrastructure development, and land-use planning, all of which can be used to advance economic development and strengthen national security in the Great Lakes region. During the last few million years, the Great Lakes region has experienced repeated glacial advances and retreats, leaving behind extensive sediments, abundant natural resources, and widespread effects on the underlying bedrock geology (Swezey and others, 2022). Linked by shared histories of past glaciations, industrial agriculture, and legacy automotive, coal, steel, and manufacturing industries, the GLGMC member States collaborate to improve the understanding of the 3D distribution of the sediments overlying the region’s bedrock (fig. 1). Developing a comprehensive subsurface 3D framework of this glaciated terrain can provide earth science data to policymakers at all levels. These insights facilitate informed decisions on the exploration, use, and protection of vital resources, such as critical minerals, industrial materials, and aquifers, thereby supporting economic prosperity and the well-being of the citizens of this region. Since its inception in 1998, the Coalition has completed more than 100 geologic mapping projects across the Great Lakes region. Each project aims to deliver geologic maps, 3D datasets, and other information that improves understanding of the geology of the Great Lakes region, with an emphasis on economic and water resources. Key deliverables include 3D geologic maps and models typically portraying sediment thickness, often derived from top-of-bedrock and borehole data. These products are developed through a combination of fieldwork, subsurface modeling, and the collection and analysis of rock and sediment cores. To support Coalition goals, member States collaborate with scientists working on related STATEMAP, EDMAP, and FEDMAP projects. Coalition scientists also engage with Tribal Nations in the Great Lakes region to ensure that Tribal interests pertaining to Coalition work are addressed. Through this collaboration, the Coalition unites the efforts of State, Federal, and Tribal Nation stakeholders to advance geologic data production and enhance understanding of the geologic resources of the Great Lakes region.

Illinois, Indiana, Michigan, Minnesota, New York, ↗