Geology ReportsSearch

Geology topics

Browse USGS reports

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

1,748 records · Page 66Linked to original sources

Evaluation of an open earthquake early warning system in Mexico, and laboratory tests of their sensors

Microelectromechanical system (MEMS) accelerometers are useful for seismological and engineering applications because of their ability to record unsaturated large seismic signals. Recent advances in MEMS technologies enable the design of instruments with improved capabilities that also allow the recording of small signals. As a result, MEMS can be useful across a broad dynamic range and for both major earthquakes and smaller magnitude events. Here, we analyze the performance of a MEMS‐based accelerometer with the capability of real‐time data transmission. We discuss the self‐noise level, dynamic range, and sensitivity, along with the timing precision and data transmission latency, and compare these parameters to other MEMS‐based instruments. We also summarize observations from a regional network deployed in southern Mexico over a period of 3+ yr for the purpose of earthquake early warning. In addition to the sensor evaluation, we present a large, openly available data set of strong motion data from the Mexican network that comprises continuous ground‐motion records from 24 accelerometers in the period between 2017 and 2022.

Seismological Research Letters

Preliminary observations of the April 5th, 2024, Mw4.8 New Jersey earthquake

On 5 April 2024, 10:23 a.m. local time, a moment magnitude 4.8 earthquake struck Tewksbury Township, New Jersey, about 65 km west of New York City. Millions of people from Virginia to Maine and beyond felt the ground shaking, resulting in the largest number (>180,000) of U.S. Geological Survey (USGS) “Did You Feel It?” reports of any earthquake. A team deployed by the Geotechnical Extreme Events Reconnaissance Association and the National Institute of Standards and Technology documented structural and nonstructural damage, including substantial damage to a historic masonry building in Lebanon, New Jersey. The USGS National Earthquake Information Center reported a focal depth of about 5 km, consistent with a lack of signal in Interferometric Synthetic Aperture Radar data. The focal mechanism solution is strike slip with a substantial thrust component. Neither mechanism’s nodal plane is parallel to the primary northeast trend of geologic discontinuities and mapped faults in the region, including the Ramapo fault. However, many of the relocated aftershocks, for which locations were augmented by temporary seismic deployments, form a cluster that parallels the general northeast trend of the faults. The aftershocks lie near the Tewksbury fault, north of the Ramapo fault.

New Jersey

Onset of aftershocks: Constraints on the Rate-and-State model

Aftershock rates typically decay with time t after the mainshock according to the Omori–Utsu law, R (t)=K(c+t) −p ⁠ , with parameters K , c , and p . The rate‐and‐state (RS) model, which is currently the most popular physics‐based seismicity model, also predicts an Omori–Utsu decay with p = 1 and a c ‐value that depends on the size of the coseismic stress change. Because the mainshock‐induced stresses strongly vary in space, the c ‐value should vary accordingly. Short‐time aftershock incompleteness (STAI) in earthquake catalogs has prevented a detailed test of this prediction so far, but the newly developed a ‐positive method for reconstructing the true earthquake rate now allows its testing. Using previously published slip models, we calculate the coseismic stress changes for the six largest mainshocks in Southern California in recent decades and estimate the maximum shear as a scalar proxy of the coseismic stress tensor. Aftershock rates reconstructed for events in different stress ranges show that the rates follow a power law with p = 1 independent of stress with no clear sign of a c ‐value. The onset of the power‐law decay is abrupt and more delayed in areas with smaller stress changes. The observations do not necessarily contradict the RS model, as STAI limits the resolution for early aftershocks, and the RS model can reproduce the observations for specific Aσ values. However, the observations lead to strong constraints, namely Aσ <10 kPa and a power‐law decay of the background rate with distance to the fault, with exponent 2.7.

Seismological Research Letters

Comparison of water quality in shallow groundwater near agricultural areas in the Delaware Coastal Plain, 2014 and 2019

The State of Delaware has encouraged agricultural conservation practices to improve nutrient uptake by crops and mitigate nutrient transport to groundwater in the surficial aquifer. To study recent changes in groundwater quality, the U.S. Geological Survey and the Delaware Department of Agriculture (DDA) developed a network of shallow wells near agricultural areas throughout the Delaware Coastal Plain. This network was designed to characterize water quality related to agricultural practices and to detect any recent changes in shallow groundwater quality, in particular groundwater nitrate concentrations. The shallow well network was first sampled in 2014 and resampled in 2019. In 2019, field parameters (including dissolved oxygen, pH, specific conductance, and temperature), major ions, nutrients, stable isotopes of water, and isotopes of nitrate were measured in groundwater samples collected between October and December. Wells were organized into three groups based on their geochemical characteristics measured in 2014: the Agricultural, Urban, and Mixed Groups. Results from the 2019 sampling showed little change in water quality from the 2014 sampling. Land-use factors continued to be the driving influence between groups. Groundwater moves slowly and changes in groundwater quality are likely to respond slowly to changes in conservation practices. Continued sampling of both groundwater quality in this network and monitoring land management practices can help detect groundwater quality trends in the future.

Delaware

Beyond the wedge: Impact of tidal streams on salinization of groundwater in a coastal aquifer stressed by pumping and sea-level rise

Saltwater intrusion (SWI) is a well-studied phenomenon that threatens the freshwater supplies of coastal communities around the world. The development and advancement of numerical models has led to improved assessment of the risk of salinization. However, these studies often fail to include the impact of surface waters as potential sources of aquifer salinity and how they may impact SWI. Based on field-collected data, we developed a regional, variable-density groundwater model using SEAWAT for east Dover, Delaware. In this location, major users of groundwater from the surficial aquifer are the City of Dover and irrigation for agriculture. Our model includes salinized marshland and tidal streams, along with irrigation and municipal pumping wells. Model scenarios were run for 100 years and included changes in pumping rates and sea-level rise (SLR). We examined how these drivers of SWI affect the extent and location of salinization in the surficial aquifer by evaluating differences in chloride concentration near surface waters and the subsurface freshwater-saltwater interface. We found the presence of the marsh inverts the typical freshwater-saltwater wedge interface and that the edge of the interface did not migrate farther inland. Additionally, we found that tidal streams are the dominant pathways of SWI at our site with salinization from streams being exacerbated by SLR. Our results also show that spatial distribution of pumping affects both the magnitude and extent of salinization, with an increase in concentrated pumping leading to more intensive salinization than a more widely distributed increase of the same total pumping volume.

Delaware

Extending the Boore and Abrahamson (2023) modified square-root-impedance method for the development of site amplifications consistent with the full-resonance approach to a range of VS30 values

The square-root-impedance (SRI) method is commonly used to approximate the seismic site amplifications computed using the full-resonance (FR) method for gradient shear-wave velocity ( V S ) profiles that are smoothly varying with depth. The SRI site amplifications have been observed to systematically underpredict the FR site amplifications by a ratio of FR/SRI amplifications around 1.05 to 1.3 across a wide frequency range (Boore, 2013). Recently, Boore and Abrahamson (2023; hereafter, BA23) related this difference in the SRI and FR methods to differences in the exponent η of the ratio of seismic impedances between the two methods. They proposed the implementation of a modified frequency-dependent η in the SRI method to improve its match to the FR site amplifications. This modified η was derived using only five V S profiles. We investigate the performance of the BA23 η for a wide range of realistic gradient V S profiles with V S30 ranging from 180 to 1500 m/s. These gradient V S profiles are constructed using two power-law functions of depth and are constrained by the assigned VS30 value, the depth and velocity of the half-space, and depths to shear-wave velocity horizons of 1.0 and 2.5 km/s ( Z 1.0 and Z 2.5 ) based on western United States sites. Despite observing a V S30 dependence of η, we find that the BA23 η generally works reasonably well for the range of V S profiles analyzed. Using the VS30 -dependent η derived in this study results in improvements in matching the FR site amplification compared to using the BA23 η. These improvements are more pronounced for the soft-site conditions and become modest to negligible for the stiff site conditions

Bulletin of the Seismological Society of America

Estimating groundwater level records using MOVE.1 and computing monthly percentiles from estimated groundwater records in Massachusetts

The U.S. Geological Survey, in cooperation with the Massachusetts Department of Environmental Protection, performed record extensions on groundwater levels at select wells using the Maintenance of Variance Extension type 1 (MOVE.1) method. The groundwater levels estimated from these record extensions were used to compute monthly percentiles to improve future determinations of a groundwater index. In Massachusetts, 27 of 29 short-record study wells with continuous groundwater levels between 0.8 and 8.1 years were suitable for record extensions; 37 long-record index wells were used to extend the groundwater level records at the study wells. The index well selected to pair with a study well was chosen based on Pearson correlation coefficient values; cross-correlation between the two wells; geologic and topographic similarity; and smallest distance spanning the wells. Each study well and its corresponding index well have 1 or more years of concurrent, overlapping data; a Pearson correlation coefficient that exceeded a threshold value of 0.8; and a similar aquifer type and hydrologic characteristics. Of the 29 study wells, 2 showed poor correlations with all index wells and were not considered for record extensions. Performance metrics used to assess the accuracy of the MOVE.1 models indicated that most models provided reasonable estimates of groundwater levels. Root mean square error values ranged from 0.097 to 2.292 feet, with a median of 0.536 foot. Nash-Sutcliffe efficiency coefficient values ranged from 0.623 to 0.996, with a median value of 0.759. Generally, study wells in close geographical proximity to their index well resulted in stronger model performance. The average length of groundwater level records was extended by 14.1 years to a new average of 18.1 years. The estimated groundwater level records from the MOVE.1 models resulted in an increase in the range of highest and lowest groundwater levels at 23 of 27 wells. The increase in range of groundwater levels was between 0.08 to 7.95 feet. Monthly percentiles for State drought indices were computed from the estimated MOVE.1 records and observed records through December 31, 2021. Percentiles computed from estimated records show an average groundwater level about 1.0 foot lower than observed data at the 2d percentile and 0.1 foot lower at the 30th percentile.

Massachusetts

Cross-fade sampling: Extremely efficient Bayesian inversion for a variety of geophysical problems

This paper introduces cross-fade sampling, a computationally efficient Markov Chain Monte Carlo simulation method that uses a semi-analytical approach to quickly solve Bayesian inverse problems that do not themselves have an analytical solution. Cross-fading is efficient in two ways. First, it requires fewer samples to obtain the same quality simulation of the target probability density function (PDF). Secondly, it is much faster to evaluate the posterior probability of each sample than conventional sampling methods for simulating Bayesian posterior PDFs. Conventional methods require evaluating the prior probability (which describes your a priori constraints) and data likelihood (which describes the fit between the observations and the predictions of the model) for each sample model. However, cross-fading does not require evaluating the data likelihood, meaning that ‘big data’ can be fit with zero additional computational cost. Further, the cross-fading approach can be used to calculate the marginal likelihood associated with a model design, facilitating model comparison and Bayesian model averaging. Topics covered in this paper include derivation of the cross-fade approach and how it can be used to simulate Bayesian posterior PDFs and compute the marginal likelihood, discussion of the class of problems to which cross-fading can be applied (with examples from earthquake statistics, earthquake ground motion modelling, volcanic eruption forecasting, and finite fault slip modelling), demonstration of efficiency relative to existing sampling methods and discussion of how cross-fading can be used to account for prediction errors (i.e. epistemic errors) as part of the geophysical inverse problem.

Geophysical Journal International

Stream nitrate dynamics driven primarily by discharge and watershed physical and soil characteristics at intensively monitored sites: Insights from deep learning

We developed a suite of models using deep learning to make hindcast predictions of the 7‐day average backward‐looking nitrate concentration at 46 predominantly agricultural sites across the midwestern and eastern United States. The models used daily observations of discharge and meteorological variables and watershed attributes describing anthropogenic modification to hydrology, nitrogen application, climate, groundwater, land use, watershed physiographic attributes, and soils. Across all sites, discharge and watershed soil and physiographic attributes showed a strong influence on model performance. Analysis of drivers across sites revealed considerable regional differences related to controlling processes such as groundwater contributions. We tested several ways to pool data across sites to develop accurate models and make the most effective use of available data. Single‐site models, in which models are trained and tested at a single location, showed generally strong predictive performance (median Kling‐Gupta Efficiency = 0.66), and accuracy at poorly performing sites could be improved by grouping sites with similar characteristics. Developing a single model for all sites reduced performance at several locations with distinct characteristics, suggesting that there is a threshold of dissimilarity beyond which more data does not improve the model. While many deep learning studies have shown that national or even global models can outperform local models, it is not clear that this is true for water quality constituents. This study demonstrates how data can be combined effectively, using deep learning to develop accurate and interpretable models of instream nitrate at sites where varying processes are responsible for changes in nitrate concentration.

Water Resources Research

Groundwater quality near the Placerita Oil Field, California, 2018

Groundwater-quality data and potential fluid-migration pathways near the Placerita Oil Field in Los Angeles County, California, were examined by the U.S. Geological Survey to determine if oil-field fluids (water and gas from oil-producing and non-producing zones) have mixed with groundwater resources. Six of the 13 new groundwater samples collected for this study contained petroleum hydrocarbons, thermogenic gas, inorganic chemical signatures, and (or) isotopic values consistent with potential mixing with fluids from hydrocarbon-bearing formations. For historical groundwater samples, benzene was the most detected petroleum hydrocarbon. The historical groundwater samples with a benzene concentration greater than 0.5 micrograms per liter were from environmental monitoring wells at industrial or commercial facilities unrelated to oil and gas development that, in many cases, have identified soil or groundwater contamination and were not typically analyzed for other constituents that could provide additional lines of evidence for potential mixing with oil-field fluids. Methane was not detected in any of the 12 historical samples with a reported measurement. Reviewing historical data revealed factors that could potentially adversely affect groundwater quality in the study area. These factors include modified hydraulic gradients caused by large volumes of water extracted from the main production area and reinjected downgradient into nonproducing zones, well-barrier failures in wells constructed in the northern part of the oil field before the 1970s, well-barrier failures in produced-water disposal wells downgradient from the main production area, and naturally occurring hydrocarbons at shallow intervals. The groundwater samples most geochemically similar to samples from hydrocarbon-bearing formations were in areas where hydrocarbons are naturally occurring at shallow intervals and where oil development is at shallow depths. Additional data for hydraulic heads, water quality, and formation temperatures at multiple depths in areas with large injection volumes and well-integrity issues are needed to evaluate whether those factors have contributed to mixing between fluids from oil-producing or injection formations and groundwater resources.

California

Simulated mean monthly groundwater-transported nitrogen loads in watersheds on the north shore of Long Island Sound, 1993–2022

Elevated nitrogen loads are pervasive in the Long Island Sound, an estuary that receives freshwater and nutrients from both surface-water and groundwater discharge. Surface-water nitrogen loads to the Long Island Sound are relatively well characterized, but less is known about groundwater-transported nitrogen loads. Prior work on the northern shore of Long Island Sound (Connecticut and areas of New York and Rhode Island) suggested that groundwater travel times are relatively short (median less than 2 years) and that decade-long nutrient legacies are not widespread. Because the travel times are short, groundwater flow and nutrient loads likely vary substantially between months. In the current study, the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency’s Long Island Sound Study and the Connecticut Department of Energy and Environmental Protection, developed a set of models to better characterize spatial and temporal patterns of groundwater-transported nitrogen loading from atmospheric deposition, septic systems, and fertilizers within the study area. The models provide an estimate, with uncertainty, of groundwater-transported nitrogen loads in the study area, filling a key gap in the nitrogen budget for Long Island Sound. The models also highlight the spatial and temporal variation in nitrogen loading throughout the study area. The modeling workflow involved four models. (1) A soil-water-balance model was developed by using the Soil-Water-Balance software to simulate groundwater recharge across the study area for water years 2005 through 2022. The simulated mean monthly recharge from the soil-water-balance model was used as input into a groundwater-flow model. (2) The groundwater-flow model was developed by using the MODFLOW 6 software and data for water years 1993 through 2022 and simulates average monthly hydrologic conditions. The groundwater-flow model was calibrated by using the Iterative Ensemble Smoother method within the PEST++ software. The Iterative Ensemble Smoother method generates an ensemble of sets of parameter values, with each set producing reasonable simulated hydrologic parameter values. (3) An ensemble of MODPATH particle-tracking simulations were run to generate particle flow paths and travel times, with each simulation using a different set of the flow model parameters. (4) A nitrogen load model uses the MODPATH simulation outputs to track nitrogen from the land surface through multiple attenuation zones until it discharges into fresh or saline surface water. As with the groundwater-flow model, the nitrogen model simulated average monthly groundwater-transported nitrogen loads for water years 1993 through 2022. One novel aspect of the nitrogen load model is that the nitrogen attenuation parameters were calibrated to observed nitrogen loads. Across the ensemble of simulated nitrogen loads, the median study-area-wide monthly simulated nitrogen loads from the aquifer to Long Island Sound throughout the year ranged from 900 to 18,600 kilograms of nitrogen per day, with a median load of 5,100 kilograms of nitrogen per day. The simulated loads were based on average monthly conditions for water years 1993 through 2022. Loads were highest during the winter and early spring and lowest during the late summer. However, simulated travel times for groundwater and nitrogen loads discharged to Long Island Sound during summer were longer than travel times for groundwater and loads discharged during the winter, indicating that, on average, groundwater discharged during summer traveled along different, and longer, flow paths, than groundwater discharged during winter. This indicates that summer loads would respond more slowly to changes in nitrogen inputs at the water table than winter loads. Over the entire study area, approximately 15 percent of the simulated load is from atmospheric deposition sources, 30 to 40 percent is from fertilizer, and 50 to 60 percent is from septic systems. The final analysis of the study involved simulating the change in groundwater-transported nitrogen load in response to upgrading septic systems or reducing fertilizing inputs to areas of turf grass. Both management interventions reduced the groundwater-transported nitrogen load, and reductions were greater in areas with greater loads from septic systems or turf-grass fertilizers. The delay between management actions and substantial reductions in groundwater-transported nitrogen loads varied seasonally; loads during the late summer months remained elevated longer than the winter loads.

Connecticut, Rhode Island

Projected sea-level rise and high tide flooding at San Juan National Historic Site, Puerto Rico

Introduction National parks and preserves in the South Atlantic-Gulf Region contain valuable coastal habitats such as tidal wetlands and mangrove forests, as well as irreplaceable historic buildings and archeological sites located in low-lying areas. These natural and cultural resources are vulnerable to accelerated sea-level rise and escalating high tide flooding events. Through a Natural Resources Preservation Program-funded project during 2021–23, the U.S. Geological Survey, in collaboration with the National Park Service, estimated the probability of inundation at San Juan National Historic Site, Puerto Rico, and several other parks under various sea-level rise scenarios and contemporary high tide flooding thresholds. The maps produced for this effort can be used to assess potential habitat change and explore how infrastructure and cultural resources within the park may be exposed to future flooding-related hazards.

San Juan National Historic Site

ECCOE Landsat quarterly Calibration and Validation report—Quarter 1, 2024

Executive Summary The U.S. Geological Survey Earth Resources Observation and Science Calibration and Validation (Cal/Val) Center of Excellence (ECCOE) focuses on improving the accuracy, precision, calibration, and product quality of remote-sensing data, leveraging years of multiscale optical system geometric and radiometric calibration and characterization experience. The ECCOE Landsat Cal/Val Team continually monitors the geometric and radiometric performance of active Landsat missions and makes calibration adjustments, as needed, to maintain data quality at the highest level. This report provides observed geometric and radiometric analysis results for Landsats 8 and 9 for quarter 1 (January–March), 2024. All data used to compile the Cal/Val analysis results presented in this report are freely available from the U.S. Geological Survey EarthExplorer website: https://earthexplorer.usgs.gov . This quarterly report is the third to include analysis results for Landsat 9, which was launched in September 2021. The inclusion of Landsat 9 analysis results was dependent on two factors: a complete reprocessing of the Landsat 9 data archive and enough time elapsing to begin formulating lifetime trends. In April 2023, all Landsat 9 image data acquired since the satellite’s launch were reprocessed to take advantage of calibration updates identified by the ECCOE Landsat Cal/Val Team. Additional information about the Landsat 9 reprocessing effort is available at https://www.usgs.gov/landsat-missions/news/upcoming-reprocessing-all-landsat-9-data . Additional information about Landsat 9 prelaunch, commissioning, and early on-orbit imaging performance is available at https://www.mdpi.com/journal/remotesensing/special_issues/15B4V2K92K . This quarterly report is the first to not include analysis results for Landsat 7 because Enhanced Thematic Mapper Plus imaging was suspended on January 19, 2024, after the satellite transitioned into full sunlight. The satellite has been drifting since early 2022 after being lowered from the nominal orbit altitude, and the transition into full sunlight is a result of the satellite operating in its extended science mission. Additional information about the imaging suspension is available at https://www.usgs.gov/landsat-missions/news/landsat-7-imaging-suspended . Additional information about the Landsat 7 extended science mission is available at https://www.usgs.gov/landsat-missions/landsat-7-extended-science-mission .

Open-File Report

Testing rate‐and‐state predictions of aftershock decay with distance

We analyze aftershocks of the 2019 M 7.1 Ridgecrest mainshock and isolated M 5–6 mainshocks in southern California to test predictions made by the rate‐and‐state friction model of Dieterich (1994) . Rate‐and‐state friction predicts that the seismicity rate after a stress step follows Omori decay, where the Omori c ‐value, which is the saturation in aftershock rate observed at small times, is larger for smaller stress steps. Put in the context of an aftershock sequence, this predicts that the Omori c ‐value will be systematically larger at greater distances from the mainshock. To our knowledge, this predicted effect has not been observed. In part this may be because the Omori c ‐value is difficult to measure because it often reflects short‐term catalog incompleteness rather than a true saturation in aftershock rate. We explore the dependence of the Omori c ‐value on the distance to the mainshock by applying the “ a ‐positive” method ( van der Elst and Page, 2023 ). This method is insensitive to short‐term aftershock incompleteness and allows resolution of the true aftershock rate deep into the mainshock coda. For aftershocks of the Ridgecrest mainshock and stacked M 5–6 mainshocks, we observe systematic differences in early aftershock rates, relative to mainshock distance, consistent with the predictions of rate‐and‐state friction. Furthermore, for the larger Ridgecrest dataset, we observe that aftershocks nearer to the mainshock start earlier, and we resolve a flattening of the Omori curve consistent with a larger Omori c ‐value for the farthest aftershocks, as predicted by Dieterich (1994) .

Seismological Research Letters

Groundwater and surface-water interactions in the Lower Duwamish Waterway, Seattle, Washington

The U.S. Geological Survey (USGS), in cooperation with the Washington State Department of Ecology (Ecology), conducted a study to describe the current understanding of the regional groundwater system of the lower Duwamish River valley and groundwater and surface-water interactions in the lower Duwamish Waterway. The lower Duwamish Waterway is the final 5-mile (mi) reach of the Duwamish River before it empties into Elliott Bay in Puget Sound near Seattle, Washington. A nearshore site (hereinafter referred to as “Nearshore Site” to distinguish the particular site from general discussions of nearshore areas) along the western shoreline of the Duwamish River, about 1.5 mi upstream from the river mouth, was selected for focused groundwater data collection by USGS. Data loggers were deployed in seven groundwater wells and one stilling well in the Duwamish River to measure specific conductance, temperature, and depth at 15-minute intervals for a period of about 2 years. At the Nearshore Site during 2020–22, water levels in the shallow wells were 3–8 feet (ft) higher than water levels in the deep wells, providing evidence for a low-permeability layer between the shallow and deep aquifers in this area. The shallow wells had a pronounced seasonal variability, with high water levels in winter and low water levels in summer. Data from the deep wells showed far less seasonal variability, with slight increases in winter and a near-constant water level from spring to autumn. The deep wells had a strong hydraulic connection to the Duwamish River, as evidenced by the synchronous water-level variability during the tidal cycle, whereas the shallow wells had minimal to no tidal response. The potentiometric maps developed for the Nearshore Site and surrounding areas indicate large differences in groundwater-flow directions for the shallow and deep aquifers at low and high tides. For the shallow aquifer, flow is toward the lower Duwamish Waterway near the Nearshore Site, regardless of the tidal condition. For the deep aquifer, a potentiometric trough forms parallel to the shoreline during high tide, indicating that groundwater flow converges from the uplands to the west and the Duwamish River to the east. The geometry of the potentiometric surfaces between the nearshore-most well and the shoreline is complex and is further confounded by intermittent shoreline armoring and other buried infrastructure, which could serve as either a barrier or a conduit to flow. Groundwater and surface-water interactions in the lower Duwamish Waterway are inherently complex as a result of three overarching factors. First, water levels in the lower reaches of the Duwamish River vary daily by 11–16 ft because of tides from Puget Sound, which create large swings in the hydraulic gradient in the nearshore groundwater system. Second, the density and chemical composition of water in the Duwamish River change daily with the tides and seasonally, which constrains how river water entering the nearshore sediments interacts with discharging groundwater. Third, the nearshore subsurface and shoreline conditions are heterogenous because of extensive shoreline armoring over the past century, which governs the flow of groundwater and infiltrating river water. These unique features of groundwater and surface-water interactions in the lower Duwamish Waterway thus govern the transport of terrestrial contaminants to the lower Duwamish Waterway. Furthermore, the heterogenous aquifer properties in the lower Duwamish Waterway contribute to spatially and temporally dynamic contaminant-transport processes.

Washington

Agricultural tile drains increase the susceptibility of streams to longer and more intense streamflow droughts

Streamflow droughts are receiving increased attention worldwide due to their impact on the environment and economy. One region of concern is the Midwestern United States, whose agricultural productivity depends on subsurface pipes known as tile drains to improve trafficability and soil conditions for crop growth. Tile drains accomplish this by rapidly transporting surplus soil moisture and shallow groundwater from fields, resulting in reduced watershed storage. However, no work has previously examined the connection between tile drainage and streamflow drought. Here, we pose the question: does the extent of watershed-level tile drainage lead to an increased susceptibly and magnitude of streamflow droughts? To answer this, we use daily streamflow data for 122 watersheds throughout the Midwestern United States to quantify streamflow drought duration, frequency, and intensity. Using spatial multiple regression models, we find that agricultural tile drainage generates statistically significant ( p < 0.05) increases in streamflow drought duration and intensity while significantly reducing drought frequency. The magnitude of the effect of tile drainage on streamflow drought characteristics is similar to that of water table depth and precipitation seasonality, both of which are known to influence streamflow droughts. Furthermore, projected changes in regional precipitation characteristics will likely drive the installation of additional tile drainage. We find that for each 10% increase in tile-drained watershed area, streamflow drought duration and intensity increase by 0.03 d and 12%, respectively, while frequency decreases by 0.10 events/year. Such increases in tile drainage may lead to more severe streamflow droughts and have a detrimental effect on the socio-environmental usage of streams throughout the Midwest.

Illinois, Indiana, Iowa, Michigan, Minnesota, Ohio

Are the horizontal-to-vertical spectral ratios of earthquakes and microtremors the same?

We consider the similarities and differences between earthquake and microtremor horizontal‐to‐vertical spectral ratios (eHVSR and mHVSR, respectively) using a dataset of 161 sites in southern California. Quantitative comparisons are made in terms of the eHVSR and mHVSR lognormal median curves, as well as the frequencies and amplitudes associated with the fundamental‐ and higher‐mode resonances where present. The results show only 58% of the eHVSR–mHVSR pairs agree in terms of their median curve and only 25% of the eHVSR–mHVSR pairs agree in terms of shared resonances, which increases to 68% if flat HVSRs are considered equivalent. Furthermore, while the shared resonances match very well in terms of frequency (root mean square error, RMSE, <0.11 Hz), the amplitudes of those resonances do not agree (RMSE >1.6). These findings demonstrate that while eHVSR and mHVSR agree at some sites, they are not equivalent at all sites. To investigate if the agreement between eHVSR and mHVSR could be related to features of the microtremor data, earthquake recordings, and/or the site conditions, three machine learning (ML) models at varying levels of interpretability are presented. The ML models—which include multivariate logistic regression, gradient‐boosted trees, and support vector machines—show only partial success at using site‐specific data to predict whether eHVSR and mHVSR will likely agree in terms of their median curve (accuracy of 78%) and number of resonances (accuracy of 84%). Therefore, we conclude that while eHVSR and mHVSR can be quite similar in terms of resonant frequencies at some sites, they are not identical at all sites. Furthermore, preliminary evidence shows that the agreement of eHVSR and mHVSR can be predicted a priori given features of the microtremor measurements, earthquake recordings, and site conditions, although a larger dataset will be necessary for developing a robust predictive model.

California

Geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers within northern Medina County, Texas

During 2023–24, the U.S. Geological Survey, in cooperation with the Edwards Aquifer Authority, revised a previous publication of the geologic framework and hydrostratigraphy of the Edwards and Trinity aquifers that was completed during 2018–20 within northern Medina County, Texas. The purpose of this report is to present the updated geologic framework and hydrostratigraphy of the rocks containing the Edwards and Trinity aquifers in northern Medina County from field observations of the surficial expressions of the rocks. The report includes a detailed 1:24,000-scale hydrostratigraphic map with names and descriptions of the geologic and hydrostratigraphic units (HSUs) in the study area. This study includes updates to the geology of the Kainer Formation (or its stratigraphic equivalent, the Fort Terrett Formation) with the addition of a burrowed unit between the basal nodular and dolomitic members. The hydrostratigraphy was also updated with the addition of HSU IIA for the upper part of the Devils River Limestone and the Seco Pass HSU for the burrowed member of the Kainer (or Fort Terrett) Formation. The Cretaceous age rocks (listed in ascending order) in the study area are part of the Trinity Group, Edwards Group and stratigraphically equivalent Devils River Limestone, Washita Group, Eagle Ford Group, Austin Group, and Taylor Group, with isolated areas where Late Cretaceous age igneous rocks have intruded. The groups and formations are composed primarily of relatively thick layers of clays, shales, and limestone. The igneous rocks are coarse-grained ultramafic in composition. Hydrostratigraphically, the rocks exposed in the study area (listed in descending order from land surface) are igneous, the upper confining unit to the Edwards aquifer, the Edwards aquifer, the upper zone of the Trinity aquifer, and the upper part of the middle zone of the Trinity aquifer. The karstic carbonate Edwards and Trinity aquifers developed because of their original depositional history, primary and secondary porosity, diagenesis, fracturing, and faulting. These factors have resulted in development of modified porosity, permeability, and transmissivity within and between the aquifers.

Texas