Geology Reports⌕ Search

Geology topics

Browse USGS reports

Search indexed USGS publications on groundwater, aquifers, geologic maps, mineral resources and earthquakes. Explore source records by subject and place.

1,748 records · Page 19Linked to original sources
USGS2026

Characterizing precariously balanced rocks (PBRs) in the eastern United States for estimating maximum past earthquake ground motions

Fragile geologic features (FGFs) can be used to estimate an upper bound to the strength of earthquake ground shaking in the past thousands to tens of thousands of years. FGFs could be especially useful in the eastern United States, where few active faults are available for paleoseismic studies and where low seismic attenuation means that an earthquake could damage FGFs at large distances. This article describes a pilot study of one form of FGF, precariously balanced rocks (PBRs), in the Blue Ridge of Virginia, ∼160 km from the central Virginia seismic zone (CVSZ) and ∼100 km from Virginia’s Giles County seismic zone (GCSZ). The main goal is to develop and refine methods for studying PBRs in the eastern United States. Photogrammetric 3D models of the rocks were used to locate their centers of mass and delineate their basal contacts, with the latter corroborated by wrapping a wire around the bases to verify the circumferences. Relations between hill geometry and amplification were used to estimate topographic amplification. Seismometers on the PBRs provided the frequencies, amplitudes, and directions of rocking after giving the rocks gentle pushes. The levels of ground shaking likely to topple the rocks were compared with the median hazard curves from the U.S. Geological Survey’s National Seismic Hazard Model and were used to map magnitudes of earthquakes in the nearby region likely to topple the rocks. Results indicate that an M w ≥ 7.5 earthquake is needed in the CVSZ or near the 2020 Sparta, North Carolina, earthquake to topple the two most fragile PBRs and that an earthquake of ~ M w 7–7.5 in the GCSZ is needed. The fragilities and estimated ages of the PBRs (20–40 ka) are thus consistent with the absence of such events in the historical record in the nearby region.

eastern United States↗
USGS2026

Forecasting volcanic activity in Germany—A multi-criteria approach

Igneous activity, including shallow intrusions and volcanism, has the potential to disrupt underground critical infrastructure. Notably, future underground infrastructure projects like high-level radioactive waste repositories must be sited in areas of extremely low disruption probability by igneous activity. In Germany, according to the Repository Site Selection Act of 2017 (Standortauswahlgesetz, or StandAG), areas in which Quaternary volcanism is either present or future volcanic activity is expected within the next 1 million years (m.y.) must be excluded from the site selection process. Although the locations of regions with Quaternary volcanism are reasonably well known in Germany, forecasting potential igneous activity at intraplate volcanic fields is challenging, as many processes and their interactions control the spatial distribution of volcanic centers. Here, a semi-quantitative, multi-criteria approach is proposed for a regional evaluation of the relative potential of future igneous activity in Germany. A variety of geoscientific indicators are used, including seismic anomalies in Earth’s mantle, gravity data, tectonic activity, sutures, ground motion, earthquakes, mantle degassing centers, and geochronological data of volcanic rocks. The indicators describe the sequence of processes from potential melt generation in Earth’s mantle, through ascent and accumulation of melt within the lithosphere, to eruption at Earth’s surface. In total, 15 out of 30 proposed geoscientific indicators are selected and quantified using 20 total assigned parameters. Defined threshold values are used to spatially delimit relevant parameter properties to focus on areas with higher potential of future magmatic activity. To consider uncertainties of parameters and their underlying processes, which are usually more spatially extensive below ground, buffer zones are defined in which values of relevance decrease with increasing distance from the initial lateral shape of a parameter. Normalized parameters are combined into an index, whose spatial value distribution is used to differentiate the relative potential of future igneous activity (within the next 1 m.y.). The sensitivity of the results is shown by varying the weighting factors for the relevant parameters in country-wide index maps. Thereby, profiles illustrate the distribution of the resulting index values and respective index fractions of various parameters. Different index maps for the relative potential of future igneous activity are presented and can be used for hazard assessments.

Professional Paper↗
USGS2026

Stream sediment sources in Medicine Creek, northern Missouri and southern Iowa

This report presents the results of a cooperative study by the U.S. Geological Survey and Missouri Department of Natural Resources to quantify sediment transport source contributions in the Medicine Creek drainage basin. Understanding relative source contributions provides valuable information for selecting the conservation practices that may be most effective in reducing sediment and sediment-associated nutrient transport in the Medicine Creek drainage basin and similar areas of the Lower Grand River drainage basin. Sediment samples were collected from potential contributing areas (source samples) and from fluvial-transported samples (target samples). Source sample types included streambanks, row crop fields, and a combined pastures and forests category. Samples were analyzed for particle size and quantity of carbon, nitrogen, stable isotopes of carbon and nitrogen, and 49 mineral elements as potential tracers. Results for the carbon stable isotope ratio of carbon-13/carbon-12 (δ 13 C) and concentrations of total carbon, total nitrogen, calcium, potassium, and copper were selected by discriminant function analysis as the best combination of multiple tracers to differentiate each source type. The discriminant function analysis poorly differentiated pastures and forests, so these source types were combined. The sources defined by the discriminant function analysis were then used in an unmixing model to apportion sources for each target sample. In the study area, transported sediment was predominantly bank sediment, with an overall average of 86.9 percent of suspended-sediment samples and depositional streambed samples attributed to bank material. Suspended-sediment samples from the mainstem of Medicine Creek were dominated by bank sediments (average of 95.8 percent), and depositional streambed samples from throughout the drainage basin had more variable source contributions with an average of 71.1 percent attributed to bank material. The relative importance of upland sources (row crop fields and the combined pastures and forests category) varied seasonally and with streamflow but was not related to land use or drainage basin size. Relative contributions from upland sources were greater in the summer through winter rather than spring and during lower streamflow, though this may be driven by the seasonality of streamflow. These results indicate management practices that reduce bank erosion could be effective strategies for managing the dominant source of sediment and sediment-associated phosphorus.

Iowa, Missouri↗
USGS2026

Open-source gravity reduction workflows for geothermal resource assessment

Potential-field geophysical data such as gravity can enhance understanding of geothermal resources at all stages of the resource life cycle, including assessment, exploration, development, and monitoring, and at multiple scales, from the reservoir scale to regional scale. However, to make gravity data useful for geothermal resource characterization, several processing steps are required to isolate the effects of density variations in the Earth’s crust to enable the identification of structural features associated with geothermal resources. Although this process is well-established, standard computational implementations for processing gravity data that are FAIR (Findable, Accessible, Interoperable, and Reproduceable) are still lacking. This paper details ongoing efforts at the U.S. Geological Survey (USGS) to develop a standard set of open-source Python tools for gravity data reduction that align with the FAIR principles. This workflow makes use of existing open-source tools for geophysical data processing with the goal of maximizing opportunities for rapid improvements, interoperability, and adaptability to other types of geophysical data.

Conference Paper↗
USGS2026

Extreme precipitation variability and soil texture controls on water-table response

Extreme precipitation events (EPEs), a key class of hydrometeorological extremes, are intensifying globally under climate change; however, their effects on water-table dynamics across varying soil textures remain poorly understood. To better understand the impacts of EPEs, we conducted one-dimensional modeling to evaluate water-table response time, displacement, recession time, and total recharge under EPEs of 0.20 m, 0.40 m, and 0.60 m amounts, applied over 1-, 7-, and 20-day durations across twelve soil textures. The results show that coarse soils (i.e., sand) respond within days, while fine soils (i.e., clay) may take over 200 days. Water-table displacement ranged from 0.30 to 1.64 m and increased with EPE magnitude. The time it took for water tables to recede ranged from 1.2 to 3.0 years. A first-order estimate of total possible recharge, calculated from porosity and displacement, ranged from 17% (clay) to 97% (sand), averaging ~63% across soil textures. These findings highlight that recharge is primarily governed by EPE magnitude and soil properties, not event duration. This modeling effort provides new insight into how soil texture modulates groundwater response to extreme precipitation, informing future water budget and resilience assessments.

Water↗
USGS2026

Special issue “The 2024 M7.6 Noto Peninsula earthquake and seismic swarm”

The 2024 Mw7.5 (M JMA 7.6) Noto Peninsula earthquake struck the Noto Peninsula, central Japan on January 1, 2024, causing widespread damage. This Mw7.5 mainshock, together with the prolonged seismic swarm that persisted in the northeastern Noto Peninsula since the end of 2020, of which the largest event was the 2023 M JMA 6.5 earthquake, constitutes one of the most significant seismic sequences in Japan in recent decades. The sequence provides a rare opportunity to investigate the complex interplay among swarm activity, fluid migration, fault geometry and distribution, and the preparatory conditions required for a large inland crustal earthquake. Motivated by this scientific context, this special issue brings together studies examining the sequence from diverse disciplinary perspectives, incorporating seismic, geodetic, and tsunami-related observations and modelling.

Noto Peninsula↗
USGS2026

Deformed submarine terraces in Puget Sound, Pacific Northwest, indicate only one M >~7.5 earthquake on the Seattle fault zone in the past 11,000 yr

Submerged marine terraces in Puget Sound, deformed across the Seattle fault zone (SFZ), indicate that only one earthquake as large as M~7.5 has occurred in at least the past 11 kyr. Previous paleoseismic studies document a M~7.5 earthquake between 923–4 CE, which uplifted coastal marine terraces by as much as 8 m. We demonstrate that this earthquake was the only such event since ~11 ka by mapping and quantifying deformation of older marine terraces, now submerged in Puget Sound. The submerged terraces, attributed to a late-glacial sea-level lowstand, record both glacial isostatic rebound and tectonic deformation. Vertical offset of the ~11 ka terraces within the SFZ is comparable to that of the marine terraces uplifted in 923 CE, implying no additional large (M>~7.5) earthquake on the SFZ since ~11 ka. This result implies a longer recurrence interval than current hazard estimates, which assumes recurrence of M>7.1 events every 5 kyr. Our mapping of SFZ deformation since ~11 ka also supports fault segmentation and contiguous block uplift between the Seattle and Tacoma fault zones.

Washington↗
USGS2026

Ground-motion aleatory-variability models for Puerto Rico and the U.S. Virgin Islands

I develop independent logic trees for aleatory variability for crustal and subduction-zone (interface and intraslab) earthquakes for seismic hazards analyses in Puerto Rico and the U.S. Virgin Islands (PRVI) from existing suites of ground-motion models (GMMs) and from ground-motion datasets, including a regional PRVI dataset. The aleatory variability models are parameterized using a partially nonergodic partitioning of standard deviation that consists of independently developed between-event ( ), site-to-site ( ), and event-corrected single-station ( ) standard deviation components. The effects of nonlinear site response on aleatory variability are incorporated through additional terms that modify the standard deviation components. Because one goal of this work is to develop independent logic trees for aleatory variability that synthesize the aleatory variability models from GMMs, I make use of the functional forms of the input GMMs. The PRVI dataset contains a limited number of stations with high-quality site metadata and does not contain records from earthquakes with magnitudes greater than 6.1, so I choose not to develop the aleatory variability models from the regional dataset alone. Instead, the standard deviation components from regional ground-motion data are evaluated against the components derived from GMMs and from available global datasets, and regionalized standard deviation components are incorporated where there is evidence that regional effects exhibit substantial differences. The resulting logic trees for aleatory variability consist of models of and that are consistent with semiempirical GMMs for active crustal and subduction-zone regimes, and two alternative models of , including one model that exhibits site-to-site variability informed by PRVI data, with values that exceed global models. The aleatory variability models may be considered in future hazards assessments in PRVI to simplify the hazard calculations, to incorporate regional ground-motion variability effects, and to enable direct logic-tree weighs of aleatory variability.

Puerto Rico, U.S. Virgin Islands↗
USGS2026

Reconstructing the Quaternary depositional history using geologic mapping and three-dimensional modeling of the subsurface near Fort Morgan, northeastern Colorado

Centered on Fort Morgan, Colorado, this study is intended to build from previous work by adding a three-dimensional (3D) view of the subsurface to better understand the depositional history of Quaternary deposits. A 1:100,000 scale geologic map was made by combining previous geologic maps, regional soil maps, and recent field investigations. In addition to the geologic mapping, drill hole lithologic data from water wells and oil and gas exploration were compiled and lithologic units simplified to best represent the stratigraphy of the Quaternary deposits. From these subsurface data, a 3D subsurface model was constructed, trimmed at the surface by a digital elevation model, and a bedrock surface foundation gridded from drill hole data was added. The surface of the 3D model was then compared visually to the surficial geologic map. Cross sections were constructed from the 3D model and compared to site-specific drilling that was done as part of this project. Finally, the model was examined in detail to reconstruct the depositional history of the subsurface alluvial and eolian units. Alluvial and fluvial drainage basins exposed in the subsurface have a greater areal extent than the present-day narrow drainages. Older eolian sand in the subsurface tends to be interbedded with loess indicating coeval deposition. Holocene sand, both eroded from bedrock exposed at the surface north of the study area and reworked from the South Platte River, buries most of the interbedded older sand and loess.

Colorado↗
USGS2026

Groundwater budget for the Mountain Home area, southern Idaho, 2022–23

The U.S. Geological Survey, with funding from the Idaho Department of Water Resources, developed a groundwater budget for the Mountain Home area in southern Idaho for irrigation year 2023 (November 1, 2022–October 31, 2023). This study focused on the water balance across the Cinder Cone Butte Critical Groundwater Area (CGWA), Mountain Home Groundwater Management Area (GWMA), and the rest of the study area (RoSA), compiling data from various sources, including precipitation records, groundwater level measurements, metered groundwater pumpage data, surface water diversions and evapotranspiration (ET) estimates derived from remote sensing satellite imagery, and ground-based reference data. Key inflow components included recharge from applied surface water irrigation (which incorporates incidental recharge from irrigation practices and conveyance losses), estimated tributary streamflow, and estimated mountain block recharge. The key outflow components were groundwater pumpage for irrigation, municipal, industrial, and domestic uses, and ET. Recharge from applied irrigation and mountain block recharge were the largest inflows, and groundwater pumpage for irrigation was the largest outflow. The CGWA had a positive groundwater budget residual of 2,170 acre-feet (acre-ft), which contrasts with observed long-term groundwater level declines and historical trends of storage depletion. This positive residual is likely associated with unquantified outflows, including lateral groundwater flow out of the subregion, or other complexities, such as overestimated tributary contributions relative to the actual recharge for the 2023 water budget. The GWMA exhibited a positive residual of 56,563 acre-ft, primarily owing to recharge from applied surface water irrigation and areal recharge during a wetter-than-average year, which allowed irrigation entities to deliver more water from in-basin and out-of-basin reservoirs. The RoSA showed a large positive residual of 124,933 acre-ft. The interpretation of these positive residuals must account for significant uncertainties, including estimations of areal recharge, tributary streamflow (particularly losses and diversions), ET, the volume of surface water loss to the Snake River, lateral groundwater flows between subregions and across study area boundaries, and the unquantified groundwater discharge to the Snake River. These uncertainties, in combination with the complex hydrogeologic controls on water movement and limitations of remotely sensed data, directly affect the accuracy of water availability assessments. Future data collection efforts would help reduce these uncertainties and support water resource management decisions in the Mountain Home area. Key efforts could include installing additional streamflow gaging stations (particularly to quantify tributary losses and gains and surface water losses to the Snake River), improving groundwater pumpage metering, and validating remotely sensed ET data with ground-based measurements. Furthermore, to better quantify unrepresented or highly uncertain fluxes, focused investigations on groundwater discharge to the Snake River, lateral groundwater flows between subregions and across study area boundaries, and a more robust determination of the actual influence and volume of mountain block recharge would help refine future water availability assessments for the Mountain Home area.

Idaho↗
USGS2026

Decadal trends in the quality of groundwater used for public drinking-water supply in California, 2004–2023, California groundwater ambient monitoring and assessment program, priority basin project

This study provides a comprehensive assessment of decadal changes in the quality of groundwater used for public drinking-water supply at 444 monitoring sites across California during 2004–2023. We assessed decadal step trends in groundwater quality for 145 water-quality constituents and geochemical indicators statewide and across geographic and land-use based network groups. We evaluated the statistical significance of directional changes (predominant increase or decrease of constituent concentrations) and the magnitude of those changes across all network groups. Uranium showed the most widespread directional and high-magnitude increases of all constituents with regulatory benchmarks statewide, particularly in the agriculture-dominated Central Valley as well as urban- and desert-dominated regions of Southern California. Fluoride and perchlorate showed the most widespread directional and high-magnitude decreases of all constituents with regulatory benchmarks statewide, which were also most pronounced in Southern California. Although arsenic and nitrate did not often register significant directional changes across network groups, they showed widespread, high-magnitude changes in both directions (increase and decrease) at levels often exceeding 10 percent of respective regulatory benchmarks statewide. Triazine herbicides (atrazine and simazine) and the gasoline oxygenate methyl tert-butyl ether (MTBE) showed significant directional decreases statewide, but not at levels considered to be of high magnitude compared to respective regulatory benchmarks. We observed significant directional and high-magnitude increases of total dissolved solids (TDS) statewide, which were most pronounced in agricultural areas. Analysis of explanatory geochemical indicators indicated that prevalent statewide increases of alkalinity and calcium were the predominant components of the observed statewide increases in TDS by mass. Widespread increases in groundwater alkalinity and calcium across agricultural and urban areas may be related, in part, to warm-season irrigation and other anthropogenic factors that have shifted soil weathering dynamics over the long term. Increasing alkalinity concentrations were related to increasing uranium concentrations, particularly in areas with aquifer materials derived from granitic rocks. Conversely, increasing calcium concentrations were related to decreasing fluoride concentrations, particularly in areas where fluoride occurred naturally at elevated concentrations. Decrease of perchlorate, triazine herbicides, and MTBE are likely related to decreased anthropogenic source inputs over time and natural attenuation in aquifers.

EarthArXiv↗
USGS2026

Small earthquake moment magnitude and implications for frequency–magnitude scaling of injection induced earthquakes of the Raton Basin

Accurate estimation of earthquake source parameters—such as moment magnitudes, corner frequencies, and stress drops—is essential for improving seismic hazard assessments and understanding earthquake physics. In this study, moment magnitudes ( M W ) are calculated for 31,581 earthquakes associated with wastewater injection in the Raton Basin (located along the border between northern New Mexico and southern Colorado) between 2016 and 2024 using radiative transfer theory to fit coda decay envelopes. Our results show that it is feasible to estimate moment magnitudes down to M W ~1 with coda envelopes from a small local monitoring network. Significant differences were found between M W and local magnitudes ( M L ) for small earthquakes ( M < 3.0). A linear relationship was optimized to convert M L to M W : M W = 0.7 M L + 0.96 and M W = 0.73 M L + 0.99 (for the events reported by the U.S. Geological Survey), which can be applied in future studies of Raton Basin seismicity. We find that b -values calculated employing different methods and using M L are approximately 1.0, while those using M W range from 1.2 to 1.4. A larger estimate of the b -value could influence interpretations of the statistical behavior of earthquakes associated with injection and consequently seismic hazard assessments based on a magnitude–frequency distribution. The potential differences between local versus moment magnitude-based earthquake statistics should be considered in other seismically active regions.

Colorado, New Mexico↗
USGS2026

Wavelet Inversion for SliP (WISP): Open-source earthquake slip modeling software

Models of the spatiotemporal evolution of earthquake slip, termed finite-fault models, are a critical component of rapid earthquake and tsunami response, earthquake forecasting, seismic ground-motion estimates, and studies of earthquake kinematics. Here, we detail a newly released finite-fault modeling software, Wavelet Inversion for SliP (WISP), in use at the U.S. Geological Survey’s National Earthquake Information Center (NEIC) and available to the public. WISP version 1.1.0 allows inversion of teleseismic body and surface waves, as well as local strong-motion, static and dynamic Global Navigation Satellite System, and satellite imagery (e.g., Interferometric Synthetic Aperture Radar) observations on single or multiple planar fault segments. The software is used in NEIC rapid response of earthquakes M w ≥ 7, generally resulting in a published model within the first few hours after the event origin time. The rupture location and dimensions are then used as inputs to downstream products to estimate earthquake shaking, predict loss, and model the likelihood of secondary hazards, namely landslides and liquefaction. WISP is also used in research studies to evaluate the characteristics of complex ruptures including multifault ruptures and earthquake doublets, among others. The WISP version 1.1.0 software release is composed of Python-wrapped FORTRAN code to accomplish the inversion procedure. A simple command line interface facilitates ease of use even for those with only a cursory knowledge of Python scripting. WISP version 1.1.0 includes a Jupyter Notebook tutorial demonstrating use of the software for modeling the 2015 M w 8.3 Illapel, Chile, earthquake. In parallel with the tutorial, we demonstrate the typical usage of the WISP software using the M w 8.3 Illapel earthquake example here.

Seismological Research Letters↗
USGS2026

Site response models based on geometric parameters for southern California sedimentary basins

Site response in sedimentary basins is influenced by complex three-dimensional (3D) features, including trapping of seismic waves, focusing of seismic energy and basin resonance. Current ground motion models (GMMs) incorporate basin effects using one-dimensional parameters like V S30 and shear wave velocity isosurface depths, which are limited in capturing lateral and 3D effects. To address these limitations, we develop seismic site response models based on novel parameters that represent multi-dimensional properties of the Los Angeles Basin (LAB) geometry and shear wave velocity. We define a basin shape for the LAB using depth to subsurface geologic interfaces associated with the oldest sedimentary deposits (depth to a particular shear wave velocity horizon, i.e., 1.5 km/s - z 1.5 ) and the depth to the crystalline basement ( z cb ) which are determined using geologic cross sections and community seismic velocity model profiles. We explore a suite of geometric descriptors computed for the LAB and southern California, from which three parameters with the greatest predictive potential are selected and evaluated using empirical ground motion residual analyses in combination with the Boore et al. GMM. The results demonstrate that the zonal heterogeneity index ( ), standard deviation of the absolute difference between z 1.5 and z cb ( ) and standard deviation of z cb ( ) each provide a reduction in site-to-site variability ( ϕ S2S ) of empirical GMMs. The reduction in ϕ S2S is period-dependent, with average decreases of 3%, 26% and 6% for , , and , respectively. Although these reductions are modest from an engineering application perspective, they are statistically significant, underscoring the inherent difficulty in fully characterising complex basin effects. Collectively, these findings indicate that the inclusion of basin-specific geometric parameters yields measurable, albeit incremental, improvements in site response prediction and establishes a framework for the progressive refinement of seismic hazard characterisation within sedimentary basins.

California↗
USGS2026

Ground motions from finite faults with unknown geometry

Earthquake emergency response and loss modeling require accurate models of ground‐motion intensity metrics (IMs), such as those produced by ShakeMap. In the critical minutes and hours after an earthquake, however, knowledge of the earthquake source geometry limits the accuracy of these models, especially in areas where seismic instrumentation is insufficient to constrain the shaking intensity pattern. Previous attempts to overcome this limitation have centered on computing the mean distance metrics from a suite of assumed source geometries. That approach is inadequate with modern ground‐motion models (GMMs) because they typically include terms for the hanging wall effect, depth to top of rupture, and other nonlinear terms. Such approaches also propagate the distance uncertainty through the GMMs and may not properly allocate the additional uncertainty into the between‐ and within‐event components. Here we present Finite‐Fault SIMulation with Mixed Effects Regression (FFSIMMER), a method to address these limitations by computing IM distributions from a suite of rupture realizations that fully accounts for all geometry‐related GMM terms and allows for the separation of the between‐ and within‐event components of the total uncertainty. The accuracy of this method is limited by the available constraints on the source parameters. To address this, FFSIMMER can incorporate constraints based on knowledge of the source, such as the approximate strike and dip based on knowledge of the plate tectonics and focal mechanism of the earthquake. We demonstrate the improvement in accuracy that can be achieved with the 2025 M 7.7 Mandalay, Burma (Myanmar), earthquake by incorporating constraints on the range of plausible source parameters.

Bulletin of the Seismological Society of America↗
USGS2026

Design and function of the Autonomous Benthic Imaging and Surveying System (ABISS) for remote sensing of lake and seabed environments

Lake and seabed environments are home to fisheries and other biota that are important to ecosystems and economies, yet these environments and the species that use them are difficult to accurately assess and monitor. Traditional benthic survey techniques, like bottom trawling used by the U.S. Geological Survey, are limited by substrate constraints, poor spatial resolution and precision, and operational depth limits, hindering accurate assessment of benthic species and habitats. In response to these limitations, the U.S. Geological Survey developed the Autonomous Benthic Imaging and Surveying System, a camera system integrated into underwater vehicles, to capture high-resolution images of the lakebed. The system uses color and stereo cameras to collect imagery, which can be analyzed using computational methods to detect organisms and (or) characterize habitat features, such as geologic substrate types. The system has been integrated into autonomous underwater vehicles and into an underwater housing used by self-contained underwater breathing apparatus (SCUBA) divers. Although the engineering of the system was motivated by the need for data collection in the Great Lakes, it has potential to collect high quality data in any aqueous setting with sufficient water clarity and safe operating conditions. The Autonomous Benthic Imaging and Surveying System can operate across diverse depths and light conditions to map and quantify ecological patterns that were difficult or impossible to assess using traditional methods. The Autonomous Benthic Imaging and Surveying System offers the potential for accurate and precise monitoring and assessment of native benthic biota, invasive species, and habitat, potentially providing natural resource managers with improved information to support decision making about benthic resource management.

Great Lakes↗
USGS2026

Chronic exposure to waterborne nickel significantly reduced growth of juvenile crayfish (Faxonius virilis)

Crayfish are critical functional components of aquatic ecosystems. Previous research has documented adverse effects of mineral extraction on crayfish. Here, we characterize potential risks of mining-derived waterborne nickel (Ni) to crayfish by documenting the effects of dissolved Ni on growth and food consumption of juvenile virile crayfish ( Faxonius virilis) in a 28-day chronic laboratory exposure. Nominal Ni concentrations ranged from 31.25 to 500 micrograms per liter (µg/L; pH = 7.96 ± 0.20, hardness = 150 ± 1 milligrams per liter as calcium carbonate). Crayfish survival, carapace length, and wet weight were measured. After 28 days of exposure, a 24-h feeding trial was performed to determine differences in food consumption. During the growth trial, 99% of crayfish survived. Change in wet weight and final wet weight were the most sensitive endpoints, with 20% effect concentrations of 24.8 and 22.6 µg/L Ni, respectively. Crayfish exposed to an average of 438 µg/L Ni consumed 41% less, and weighed 65.1% less, than control crayfish. These results suggest chronic, sublethal exposure to waterborne Ni may have negative effects on crayfish growth. Reduced growth and consumption rates in crayfish could have wide-ranging consequences throughout aquatic ecosystems since crayfish are consumers, prey, keystone trophic regulators, and ecosystem engineers. Finally, these results could inform bioenergetics and may be coupled with population models to predict potential changes in population sizes of native and invasive crayfishes.

Ecotoxicology↗