Geology topics

Y. Li

Publications and source records attributed to Y. Li.

12 recordsLinked to original sources

USGS2011

Chemical structures of coal lithotypes before and after CO2 adsorption as investigated by advanced solid-state 13C nuclear magnetic resonance spectroscopy

Four lithotypes (vitrain, bright clarain, clarain, and fusain) of a high volatile bituminous Springfield Coal from the Illinois Basin were characterized using advanced solid-state 13 C nuclear magnetic resonance (NMR) spectroscopy. The NMR techniques included quantitative direct polarization/magic angle spinning (DP/MAS), cross polarization/total sideband suppression (CP/TOSS), dipolar dephasing, CH n selection, and recoupled C–H long-range dipolar dephasing techniques. The lithotypes that experienced high-pressure CO 2 adsorption isotherm analysis were also analyzed to determine possible changes in coal structure as a result of CO 2 saturation at high pressure and subsequent evacuation. The main carbon functionalities present in original vitrain, bright clarain, clarain and fusain were aromatic carbons (65.9%–86.1%), nonpolar alkyl groups (9.0%–28.9%), and aromatic C–O carbons (4.1%–9.5%). Among these lithotypes, aromaticity increased in the order of clarain, bright clarain, vitrain, and fusain, whereas the fraction of alkyl carbons decreased in the same order. Fusain was distinct from other three lithotypes in respect to its highest aromatic composition (86.1%) and remarkably small fraction of alkyl carbons (11.0%). The aromatic cluster size in fusain was larger than that in bright clarain. The lithotypes studied responded differently to high pressure CO 2 saturation. After exposure to high pressure CO 2 , vitrain and fusain showed a decrease in aromaticity but an increase in the fraction of alkyl carbons, whereas bright clarain and clarain displayed an increase in aromaticity but a decrease in the fraction of alkyl carbons. Aromatic fused-rings were larger for bright clarain but smaller for fusain in the post-CO 2 adsorption samples compared to the original lithotypes. These observations suggested chemical CO 2 –coal interactions at high pressure and the selectivity of lithotypes in response to CO 2 adsorption.

International Journal of Coal Geology↗

USGS2010

Structural features of a bituminous coal and their changes during low-temperature oxidation and loss of volatiles investigated by advanced solid-state NMR spectroscopy

Quantitative and advanced 13 C solid-state NMR techniques were employed to investigate (i) the chemical structure of a high volatile bituminous coal, as well as (ii) chemical structural changes of this coal after evacuation of adsorbed gases, (iii) during oxidative air exposure at room temperature, and (iv) after oxidative heating in air at 75 ??C. The solid-state NMR techniques employed in this study included quantitative direct polarization/magic angle spinning (DP/MAS) at a high spinning speed of 14 kHz, cross polarization/total sideband suppression (CP/TOSS), dipolar dephasing, CH, CH 2 , and CH n selection, 13 C chemical shift anisotropy (CSA) filtering, two-dimensional (2D) 1 H- 13 C heteronuclear correlation NMR (HETCOR), and 2D HETCOR with 1 H spin diffusion. With spectral editing techniques, we identified methyl CCH 3 , rigid and mobile methylene CCH 2 C, methine CCH, quaternary C q , aromatic CH, aromatic carbons bonded to alkyls, small-sized condensed aromatic moieties, and aromatic C-O groups. With direct polarization combined with spectral-editing techniques, we quantified 11 different types of functional groups. 1 H- 13 C 2D HETCOR NMR experiments indicated spatial proximity of aromatic and alkyl moieties in cross-linked structures. The proton spin diffusion experiments indicated that the magnetization was not equilibrated at a 1 H spin diffusion time of 5 ms. Therefore, the heterogeneity in spatial distribution of different functional groups should be above 2 nm. Recoupled C-H long-range dipolar dephasing showed that the fraction of large charcoal-like clusters of polycondensed aromatic rings was relatively small. The exposure of this coal to atmospheric oxygen at room temperature for 6 months did not result in obvious chemical structural changes of the coal, whereas heating at 75 ??C in air for 10 days led to oxidation of coal and generated some COO groups. Evacuation removed most volatiles and caused a significant reduction in aliphatic signals in its DP/MAS spectrum. DP/MAS, but not CP/MAS, allowed us to detect the changes during low-temperature oxidation and loss of volatiles. These results demonstrate the applicability of advanced solid-state NMR techniques in chemical characterization of coal. ?? 2010 American Chemical Society.

Conference Paper↗

USGS2009

Global irrigated area map (GIAM), derived from remote sensing, for the end of the last millennium

A Global Irrigated Area Map (GIAM) has been produced for the end of the last millennium using multiple satellite sensor, secondary, Google Earth and groundtruth data. The data included: (a) Advanced Very High Resolution Radiometer (AVHRR) 3-band and Normalized Difference Vegetation Index (NDVI) 10 km monthly time-series for 1997-1999, (b) Syste me pour l'Observation de la Terre Vegetation (SPOT VGT) NDVI 1 km monthly time series for 1999, (c) East Anglia University Climate Research Unit (CRU) rainfall 50km monthly time series for 1961-2000, (d) Global 30 Arc-Second Elevation Data Set (GTOPO30) 1 km digital elevation data of the World, (e) Japanese Earth Resources Satellite-1 Synthetic Aperture Radar (JERS-1 SAR) data for the rain forests during two seasons in 1996 and (f) University of Maryland Global Tree Cover 1 km data for 1992-1993. A single mega-file data-cube (MFDC) of the World with 159 layers, akin to hyperspectral data, was composed by re-sampling different data types into a common 1 km resolution. The MFDC was segmented based on elevation, temperature and precipitation zones. Classification was performed on the segments. Quantitative spectral matching techniques (SMTs) used in hyperspectral data analysis were adopted to group class spectra derived from unsupervised classification and match them with ideal or target spectra. A rigorous class identification and labelling process involved the use of: (a) space-time spiral curve (ST-SC) plots, (b) brightness-greenness-wetness (BGW) plots, (c) time series NDVI plots, (d) Google Earth very-high-resolution imagery (VHRI) 'zoom-in views' in over 11 000 locations, (e) groundtruth data broadly sourced from the degree confluence project (3 864 sample locations) and from the GIAM project (1 790 sample locations), (f) high-resolution Landsat-ETM+ Geocover 150m mosaic of the World and (g) secondary data (e.g. national and global land use and land cover data). Mixed classes were resolved based on decision tree algorithms and spatial modelling, and when that did not work, the problem class was used to mask and re-classify the MDFC, and the class identification and labelling protocol repeated. The sub-pixel area (SPA) calculations were performed by multiplying full-pixel areas (FPAs) with irrigated area fractions (IAFs) for every class. A 28 class GIAM was produced and the area statistics reported as: (a) annualized irrigated areas (AIAs), which consider intensity of irrigation (i.e. sum of irrigated areas from different seasons in a year plus continuous year-round irrigation or gross irrigated areas), and (b) total area available for irrigation (TAAI), which does not consider intensity of irrigation (i.e. irrigated areas at any given point of time plus the areas left fallow but 'equipped for irrigation' at the same point of time or net irrigated areas). The AIA of the World at the end of the last millennium was 467 million hectares (Mha), which is sum of the non-overlapping areas of: (a) 252 Mha from season one, (b) 174 Mha from season two and (c) 41 Mha from continuous year-round crops. The TAAI at the end of the last millennium was 399 Mha. The distribution of irrigated areas is highly skewed amongst continents and countries. Asia accounts for 79% (370 Mha) of all AIAs, followed by Europe (7%) and North America (7%). Three continents, South America (4%), Africa (2%) and Australia (1%), have a very low proportion of the global irrigation. The GIAM had an accuracy of 79-91%, with errors of omission not exceeding 21%, and the errors of commission not exceeding 23%. The GIAM statistics were also compared with: (a) the United Nations Food and Agricultural Organization (FAO) and University of Frankfurt (UF) derived irrigated areas and (b) national census data for India. The relationships and causes of differences are discussed in detail. The GIAM products are made available through a web portal (http://www.iwmigiam.org). ?? 2009 Taylor & Francis.

International Journal of Remote Sensing↗

USGS2009

Satellite-marked waterfowl reveal migratory connection between H5N1 outbreak areas in China and Mongolia

The role of wild birds in the spread of highly pathogenic avian influenza H5N1 has been greatly debated and remains an unresolved question. However, analyses to determine involvement of wild birds have been hindered by the lack of basic information on their movements in central Asia. Thus, we initiated a programme to document migrations of waterfowl in Asian flyways to inform hypotheses of H5N1 transmission. As part of this work, we studied migration of waterfowl from Qinghai Lake, China, site of the 2005 H5N1 outbreak in wild birds. We examined the null hypothesis that no direct migratory connection existed between Qinghai Lake and H5N1 outbreak areas in central Mongolia, as suggested by some H5N1 phylogeny studies. We captured individuals in 2007 from two of the species that died in the Qinghai Lake outbreaks and marked them with GPS satellite transmitters: Bar-headed Geese Anser indicus (n = 14) and Ruddy Shelduck Tadorna ferruginea (n = 11). Three of 25 marked birds (one Goose and two Shelducks) migrated to breeding grounds near H5N1 outbreak areas in Mongolia. Our results describe a previously unknown migratory link between the two regions and offer new critical information on migratory movements in the region. ?? 2009 British Ornithologists' Union.

Ibis↗

USGS2008

Trace element emissions from spontaneous combustion of gob piles in coal mines, Shanxi, China

The emissions of potentially hazardous trace elements from spontaneous combustion of gob piles from coal mining in Shanxi Province, China, have been studied. More than ninety samples of solid waste from gob piles in Shanxi were collected and the contents of twenty potentially hazardous trace elements (Be, F, V, Cr, Mn, Co, Ni, Cu, Zn, As, Se, Mo, Cd, Sn, Sb, Hg, Tl, Pb, Th, and U) in these samples were determined. Trace element contents in solid waste samples showed wide ranges. As compared with the upper continental crust, the solid waste samples are significantly enriched in Se (20x) and Tl (12x) and are moderately enriched in F, As, Mo, Sn, Sb, Hg, Th, and U (2-5x). The solid waste samples are depleted in V, Cr, Mn, Co, Ni, Cu, and Zn. The solid waste samples are enriched in F, V, Mn, Cr, Co, Ni, Cu, Zn, Sb, Th, and U as compared with the Shanxi coals. Most trace elements are higher in the clinker than in the unburnt solid waste except F, Sn, and Hg. Trace element abundances are related to the ash content and composition of the samples. The content of F is negatively correlated with the ash content, while Pb is positively correlated with the ash. The concentrations of As, Mn, Zn, and Cd are highly positively correlated with Fe2O3 in the solid waste. The As content increases with increasing sulfur content in the solid waste. The trace element emissions are calculated for mass balance. The emission factors of trace elements during the spontaneous combustion of the gobs are determined and the trace element concentrations in the flue gas from the spontaneous combustion of solid waste are calculated. More than a half of F, Se, Hg and Pb are released to the atmosphere during spontaneous combustion. Some trace element concentrations in flue gas are higher than the national emission standards. Thus, gob piles from coal mining pose a serious environmental problem. ?? 2007 Elsevier B.V. All rights reserved.

International Journal of Coal Geology↗

USGS2007

Estimating locations and total magnetization vectors of compact magnetic sources from scalar, vector, or tensor magnetic measurements through combined Helbig and Euler analysis

The Helbig method for estimating total magnetization directions of compact sources from magnetic vector components is extended so that tensor magnetic gradient components can be used instead. Depths of the compact sources can be estimated using the Euler equation, and their dipole moment magnitudes can be estimated using a least squares fit to the vector component or tensor gradient component data. ?? 2007 Society of Exploration Geophysicists.

Conference Paper↗

USGS2006

Relative importance of magnetic moments in UXO clearance applications

Surface magnetic anomaly observed in UXO clearance is mainly dipolar and, as a result, the dipole is the only moment used regularly in UXO applications. The dipole moment contains intensity of magnetization information but lacks shape information. Unlike dipole, higher-order moments, such as quadrupole and octupole, encode asymmetry properties of magnetization distribution within buried targets. In order to improve our understanding of magnetization distribution within UXO and non-UXO objects and its potential utility in UXO clearance, we present results of a 3D numerical modeling study for highly susceptible metallic objects. The basis for modeling is the solution of a nonlinear integral equation, describing magnetization within isolated objects, allowing us to compute magnetic moments of the object, analyze their relationships, and provide a depiction of the surface anomaly produced by the different moments within the object. Our modeling results show significant high-order moments for more asymmetric objects situated at typical UXO burial depths, and suggest that the increased relative contribution to magnetic gradient data from these higher-order moments may provide a practical tool for improved UXO discrimination. ?? 2005 Society of Exploration Geophysicists.

SEG Technical Program Expanded Abstracts↗

USGS2006

Numerical modeling of magnetic moments for UXO applications

The surface magnetic anomaly observed in UXO clearance is mainly dipolar and, consequently, the dipole is the only magnetic moment regularly recovered in UXO applications. The dipole moment contains information about intensity of magnetization but lacks information about shape. In contrast, higher-order moments, such as quadrupole and octupole, encode asymmetry properties of the magnetization distribution within the buried targets. In order to improve our understanding of magnetization distribution within UXO and non-UXO objects and its potential utility in UXO clearance, we present a 3D numerical modeling study for highly susceptible metallic objects. The basis for the modeling is the solution of a nonlinear integral equation describing magnetization within isolated objects. A solution for magnetization distribution then allows us to compute magnetic moments of the object, analyze their relationships, and provide a depiction of the surface anomaly produced by different moments within the object. Our modeling results show significant high-order moments for more asymmetric objects situated at depths typical of UXO burial, and suggest that the increased relative contribution to magnetic gradient data from these higher-order moments may provide a practical tool for improved UXO discrimination.

Conference Paper↗

USGS2005

Historical development of the gravity method in exploration

The gravity method was the first geophysical technique to be used in oil and gas exploration. Despite being eclipsed by seismology, it has continued to be an important and sometimes crucial constraint in a number of exploration areas. In oil exploration the gravity method is particularly applicable in salt provinces, overthrust and foothills belts, underexplored basins, and targets of interest that underlie high-velocity zones. The gravity method is used frequently in mining applications to map subsurface geology and to directly calculate ore reserves for some massive sulfide orebodies. There is also a modest increase in the use of gravity techniques in specialized investigations for shallow targets. Gravimeters have undergone continuous improvement during the past 25 years, particularly in their ability to function in a dynamic environment. This and the advent of global positioning systems (GPS) have led to a marked improvement in the quality of marine gravity and have transformed airborne gravity from a regional technique to a prospect-level exploration tool that is particularly applicable in remote areas or transition zones that are otherwise inaccessible. Recently, moving-platform gravity gradiometers have become available and promise to play an important role in future exploration. Data reduction, filtering, and visualization, together with low-cost, powerful personal computers and color graphics, have transformed the interpretation of gravity data. The state of the art is illustrated with three case histories: 3D modeling of gravity data to map aquifers in the Albuquerque Basin, the use of marine gravity gradiometry combined with 3D seismic data to map salt keels in the Gulf of Mexico, and the use of airborne gravity gradiometry in exploration for kimberlites in Canada.

Geophysics↗

USGS2005

Diet of introduced bullfrogs (Rana catesbeiana): Predation on and diet overlap with native frogs on Daishan Island, China

We examined diet of introduced Bullfrogs ( Rana catesbeiana ) and three native frog species ( Rana limnocharis , Rana nigromaculata , and Bufo bufo gargarizans ) co-occurring at a group of ponds on Daishan Island, east of China, to gain insight into the nature of potential interactions between Bullfrogs and native frog species. For postmetamorphic Bullfrogs, aquatic prey items dominated volumetrically. Prey size, diet volume and volumetric percentage of native frogs in diet increased with Bullfrog body size. The number and volumetric percentage of native frogs in the diet were not different for female and male Bullfrogs, and both were higher for adults than for juveniles. Diet overlap between males and juveniles was higher than that between males and females and between females and juveniles. Diet overlap with each native frog species of male Bullfrogs was lower than that of female Bullfrogs and juvenile Bullfrogs. We did not exam effects of Bullfrogs on native frogs but our results suggest that the primary threat posed by juvenile Bullfrogs to native frogs on Daishan Island is competition for food, whereas the primary threat posed by male Bullfrogs is direct predation. Female Bullfrogs may threaten native frogs by both competition and predation. These differences among Bullfrog groups may be attributed to differences in body size and microhabitat use.

Daishan Island↗

USGS2003

Fluid inclusion and noble gas studies of the Dongping gold deposit, Hebei Province, China: A mantle connection for mineralization?

The Dongping gold deposit (>100 t Au) occurs about 200 km inboard of the northern margin of the North China craton. The deposit is mainly hosted by syenite of a middle Paleozoic alkalic intrusive complex that was emplaced into Late Archean basement rocks. Both groups of rocks are intruded by Late Jurassic to Early Cretaceous crustal-melt granite dikes and stocks, some within a few kilometers of the deposit. The gold ores were deposited during this latter magmatic period at about 150 Ma, a time that was characterized by widespread regional north-south compression that formed the east-west-trending Yanshan deformational belt. The ores include both the telluride mineral-bearing, low sulfide quartz veins and the highly K-feldspar-altered syenite, with most of the resource concentrated in two orebodies (1 and 70). Fluid inclusion microthermometry indicates heterogeneous trapping of low-salinity (e.g., 5-7 wt % NaCl equiv) fluids that varied from a few to 60 mole percent nonaqueous volatile species. Laser Raman spectroscopy confirms that the vapor phase in these inclusions is dominated by CO2, but may be comprised of as much as 9 mole percent H2S and 20 mole percent N2; methane concentrations in the vapor phase are consistently <1 mole percent. The variable phase ratios are consistent with fluid immiscibility during ore formation. Fluid inclusion trapping conditions are estimated to be 250?? to 375??C and 0.6 to 1.0 kbar. Helium isotope studies of fluid inclusions in ore-stage pyrites indicate He/He ratios of 2.1 to 5.2 Ra (Ra = 1.4 x 10-6 for air) for orebody 1 and 0.3 to 0.8 Ra for orebody 70. The former data suggest that at least 26 to 65 percent mantle helium occurs in the fluids that deposited the veins in orebody 1. The lower values for orebody 70, which is characterized by a more disseminated style of gold mineralization, are interpreted to reflect an increased interaction of ore fluids with surrounding crustal rocks, which may have contributed additional He to the fluids. A mantle source for at least some of the components of the gold-forming fluid is consistent with upwelling of hot asthenosphere and erosion of as much as 100 to 150 km of cool Archean lithosphere beneath the craton during this time. The Dongping deposit is located along the 100-km-wide north-south gravity lineament, which marks the western border of the thinned crust. As both regional metamorphism of Mesoproterozoic and younger cover rocks, and widespread granite magmatism, also occurred at ca. 150 Ma, it is unclear as to whether one or both of these also contributed fluid and/or metals to the hydrothermal system. Importantly, these new data suggest that economically significant gold deposits of similar mineral style and fluid composition, which are scattered along the margins of the craton, may all be products of a fluid originally partly sourced within the mantle.

Economic Geology↗

USGS1998

Evidence for large prehistoric earthquakes in the northern New Madrid seismic zone, central United States

We surveyed the area north of New Madrid, Missouri, for prehistoric liquefaction deposits and uncovered two new sites with evidence of pre-1811 earthquakes. At one site, located about 20 km northeast of New Madrid, Missouri, radiocarbon dating indicates that an upper sand blow was probably deposited after A.D. 1510 and a lower sand blow was deposited prior to A.D. 1040. A sand blow at another site about 45 km northeast of New Madrid, Missouri, is dated as likely being deposited between A.D. 55 and A.D. 1620 and represents the northernmost recognized expression of prehistoric liquefaction likely related to the New Madrid seismic zone. This study, taken together with other data, supports the occurrence of at least two earthquakes strong enough to induce liquefaction or faulting before A.D. 1811 and after A.D. 400. One earthquake probably occurred around A.D. 900 and a second earthquake occurred around A.D. 1350. The data are not yet sufficient to estimate the magnitudes of the causative earthquakes for these liquefaction deposits although we conclude that all of the earthquakes are at least moment magnitude M ∼ 6.8, the size of the 1895 Charleston, Missouri, earthquake. A more rigorous estimate of the number and sizes of prehistoric earthquakes in the New Madrid seismic zone awaits evaluation of additional sites.

Arkansas, Illinois, Kentucky, Missouri, Tennessee↗