Geology Reports⌕ Search

Geology topics

William R. Selbig

Publications and source records attributed to William R. Selbig.

At least 37 records · Page 2Linked to original sources
USGS2019

Evaluation of stormwater treatment vault with Coanda-effect screen for removal of solids and phosphorus in urban runoff

Catch basins commonly are used by cities as part of a stormwater management plan to remove sediment and associated contaminants from stormwater, keeping them in compliance with regulations. Recently, the city of Madison, Wisconsin modified traditional catch basins by incorporating a fine-mesh (1-mm) Coanda-effect screen into the design with the goal of increasing removal of sediment and organic matter from stormwater. The US Geological Survey (USGS), in cooperation with the City of Madison, installed a water-quality monitoring station at such a catch basin to quantify reductions in total suspended solids (TSS), volatile suspended solids (VSS), suspended sediment concentration (SSC), total phosphorus (TP), and dissolved phosphorus (DP) from urban stormwater before entering Lake Monona. A comparison of the cumulative load from 33 samples collected during the summers of 2016 and 2017 showed 23% and 45% reductions in TSS and SSC, respectively. A smaller reduction was observed for TP, 16%, whereas DP remained unchanged. Reported traditional catch basin sediment removal varies greatly, although typical removal rates are similar. Results from this study will help regulated municipalities determine whether the use of screened catch basins can help meet water-quality goals.

Wisconsin↗
USGS2018

Hydraulic, water-quality, and temperature performance of three types of permeable pavement under high sediment loading conditions

Three permeable pavement surfaces - asphalt (PA), concrete (PC), and interlocking pavers (PIP) - were evaluated side-by-side to measure changes to the infiltrative capacity and water quality of stormwater runoff originating from a conventional asphalt parking lot in Madison, Wisconsin. During the 24-month monitoring period (2014-16), all three permeable pavements resulted in statistically significant reductions in the cumulative load of solids (total suspended solids and suspended sediment), total phosphorus, Escherichia coli ( E. coli ), and Enterococci . Most of the removal occurred through capture and retention in the void spaces of each permeable surface and aggregate base. The largest reduction in total suspended solids was for PC at 80 percent, followed by PIP and PA at 69 and 65 percent, respectively. Reductions (generally less than 50 percent) in total phosphorus also were observed, which might have been tempered by increases in the dissolved fraction observed in PIP and PA. Conversely, PC results indicated a slight reduction in dissolved phosphorus but failed to meet statistical significance. E. coli and Enterococci were reduced by about 80 percent for PC, almost twice the amount observed for PIP and PA. Results for the PIP and PC surfaces initially indicated higher pollutant load reduction than results for the PA surface. The efficiency of PIP and PC surfaces capturing sediment, however, led to a decline in infiltration rates that resulted in more runoff flowing over, not through, the permeable surface. This result led to a decline in treatment until the permeable surface was partially restored through maintenance practices, to which PIP responded more dramatically than PC or PA. Conversely, the PA surface was capable of infiltrating most of the influent runoff volume during the monitoring period and, thus, continued to provide some level of treatment. The combined effect of underdrain and overflow drainage resulted in similar pollutant treatment for all three permeable surfaces. Temperatures below each permeable surface generally followed changes in air temperature with a more gradual response observed in deeper layers. Therefore, permeable pavement may do little to mitigate heated runoff during summer. During winter, deeper layers remained above freezing even when air temperature was below freezing. Although temperatures were not high enough to melt snow or ice accumulated on the surface, temperatures below each permeable pavement did allow void spaces to remain open, which promoted infiltration of melted ice and snow as air temperatures rose above freezing. These open void spaces could potentially reduce the need for application of deicing agents in winter because melted snow and ice would infiltrate, thereby preventing refreezing of pooled water in what is known as the “black ice” effect.

Wisconsin↗
USGS2017

Collecting a better water-quality sample: Reducing vertical stratification bias in open and closed channels

Collection of water-quality samples that accurately characterize average particle concentrations and distributions in channels can be complicated by large sources of variability. The U.S. Geological Survey (USGS) developed a fully automated Depth-Integrated Sample Arm (DISA) as a way to reduce bias and improve accuracy in water-quality concentration data. The DISA was designed to integrate with existing autosampler configurations commonly used for the collection of water-quality samples in vertical profile thereby providing a better representation of average suspended sediment and sediment-associated pollutant concentrations and distributions than traditional fixed-point samplers. In controlled laboratory experiments, known concentrations of suspended sediment ranging from 596 to 1,189 mg/L were injected into a 3 foot diameter closed channel (circular pipe) with regulated flows ranging from 1.4 to 27.8 ft 3 /s. Median suspended sediment concentrations in water-quality samples collected using the DISA were within 7 percent of the known, injected value compared to 96 percent for traditional fixed-point samplers. Field evaluation of this technology in open channel fluvial systems showed median differences between paired DISA and fixed-point samples to be within 3 percent. The range of particle size measured in the open channel was generally that of clay and silt. Differences between the concentration and distribution measured between the two sampler configurations could potentially be much larger in open channels that transport larger particles, such as sand.

Conference Paper↗
USGS2016

Simulation of climate change effects on streamflow, groundwater, and stream temperature using GSFLOW and SNTEMP in the Black Earth Creek Watershed, Wisconsin

A groundwater/surface-water model was constructed and calibrated for the Black Earth Creek watershed in south-central Wisconsin. The model was then run to simulate scenarios representing common societal concerns in the basin, focusing on maintaining a cold-water resource in an urbanizing fringe near its upper stream reaches and minimizing downstream flooding. Although groundwater and surface water are considered a single resource, many hydrologic models simplistically simulate feedback loops between the groundwater system and other hydrologic processes. These feedbacks include timing and rates of evapotranspiration, surface runoff, soil-zone flow, and interactions with the groundwater system; however, computer models can now routinely and iteratively couple the surface-water and groundwater systems—albeit with longer model run times. In this study, preliminary calibrations of uncoupled transient surface-water and steady-state groundwater models were used to form the starting point for final calibration of one transient computer simulation that iteratively couples groundwater and surface water. The computer code GSFLOW (Groundwater/Surface-water FLOW) was used to simulate the coupled hydrologic system; a surface-water model represented hydrologic processes in the atmosphere, at land surface, and within the soil zone, and a groundwater-flow model represented the unsaturated zone, saturated zone, and streams. The coupled GSFLOW model was run on a daily time step during water years 1985–2007. Early simulation times (1985–2000) were used for spin-up to make the simulation results less sensitive to initial conditions specified; the spin-up period was not included in the model calibration. Model calibration used observed heads, streamflows, solar radiation, and snowpack measurements from 2000 to 2007 for history matching. Calibration was performed by using the PEST parameter estimation software suite. Simulated streamflows from the calibrated GSFLOW model and other basin characteristics were used as input to the one-dimensional SNTEMP (Stream-Network TEMPerature) model. SNTEMP was used to simulate daily stream temperature in selected stream reaches in the watershed. The temperature model was calibrated to high-resolution stream temperature time-series data measured in 2005. The calibrated GSFLOW and SNTEMP models were then used to simulate effects of potential climate change for the years 2010 through 2100. An ensemble of climate models and emission scenarios was evaluated. Downscaled climate drivers for the simulation period showed increases in maximum and minimum air temperature. Scenarios of future precipitation, however, did not show a monotonic trend like temperature. Uncertainty in the climate drivers increased with time for both temperature and precipitation. Forecasts of potential climate change scenarios showed growing season length increasing by weeks, and both potential and actual evapotranspiration rates increasing appreciably, in response to increasing air temperature. Simulated actual evapotranspiration rates increased less than simulated potential evapotranspiration rates as a result of water limitation in the root zone during the summer high-evapotranspiration period. The hydrologic-system response to climate change was characterized by a reduction in the importance of the snowmelt pulse and an increase in the importance of fall and winter groundwater recharge. The less dynamic hydrologic regime is likely to result in drier soil conditions, with relatively less drying expected in groundwater-fed systems. Groundwater discharge in the current upper cold-water reaches of Black Earth Creek is expected to decrease; flooding in downstream reaches may appreciably increase. The magnitude of changes in forecasted flow and associated groundwater/surface-water interaction is dependent on the General Circulation Model and emission scenario chosen. Potential future changes in air temperature drivers were consistently upward regardless of General Circulation Model and emission scenario selected; thus, simulated stream temperatures are forecast to increase appreciably with future climate. However, the amount of temperature increase was variable. Such uncertainty is reflected in temperature model results, along with uncertainty in the groundwater/surface-water interaction itself. The estimated increase in annual average temperature ranged from approximately 3 to 6 degrees Celsius by 2100 in the upper reaches of Black Earth Creek and 2 to 4 degrees Celsius in reaches farther downstream. As with all forecasts that rely on projections of an unknowable future, the results are best considered to approximate potential outcomes of climate change given the underlying uncertainty.

Wisconsin↗
USGS2016

Urban infrastructure and water management—Science capabilities of the U.S. Geological Survey

Managing the urban-water cycle has increasingly become a challenge for water-resources planners and regulators faced with the problem of providing clean drinking water to urban residents. Sanitary and combined sanitary and storm sewer networks convey wastewater to centralized treatment plants. Impervious surfaces, which include roads, parking lots, and buildings, increase stormwater runoff and the efficiency by which runoff is conveyed to nearby stream channels; therefore, impervious surfaces increase the risk of urban flooding and alteration of natural ecosystems. These challenges will increase with the expansion of urban centers and the probable effects of climate change on precipitation patterns. Understanding the urban-water cycle is critical to effectively manage water resources and to protect people, infrastructure, and urban-stream ecosystems. As a leader in water-supply, wastewater, and stormwater assessments, the U.S. Geological Survey has the expertise and resources needed to monitor, model, and interpret data related to the urban-water cycle and thereby enable water-resources managers to make informed decisions.

Fact Sheet↗
USGS2016

The effect of particle size distribution on the design of urban stormwater control measures

An urban pollutant loading model was used to demonstrate how incorrect assumptions on the particle size distribution (PSD) in urban runoff can alter the design characteristics of stormwater control measures (SCMs) used to remove solids in stormwater. Field-measured PSD, although highly variable, is generally coarser than the widely-accepted PSD characterized by the Nationwide Urban Runoff Program (NURP). PSDs can be predicted based on environmental surrogate data. There were no appreciable differences in predicted PSD when grouped by season. Model simulations of a wet detention pond and catch basin showed a much smaller surface area is needed to achieve the same level of solids removal using the median value of field-measured PSD as compared to NURP PSD. Therefore, SCMs that used the NURP PSD in the design process could be unnecessarily oversized. The median of measured PSDs, although more site-specific than NURP PSDs, could still misrepresent the efficiency of an SCM because it may not adequately capture the variability of individual runoff events. Future pollutant loading models may account for this variability through regression with environmental surrogates, but until then, without proper site characterization, the adoption of a single PSD to represent all runoff conditions may result in SCMs that are under- or over-sized, rendering them ineffective or unnecessarily costly.

Water↗
USGS2016

Evaluation of leaf removal as a means to reduce nutrient concentrations and loads in urban stormwater

While the sources of nutrients to urban stormwater are many, the primary contributor is often organic detritus, especially in areas with dense overhead tree canopy. One way to remove organic detritus before it becomes entrained in runoff is to implement a city-wide leaf collection and street cleaning program. Improving our knowledge of the potential reduction of nutrients to stormwater through removal of leaves and other organic detritus on streets could help tailor more targeted municipal leaf collection programs. This study characterized an upper ideal limit in reductions of total and dissolved forms of phosphorus and nitrogen in stormwater through implementation of a municipal leaf collection and street cleaning program in Madison, WI, USA. Additional measures were taken to remove leaf litter from street surfaces prior to precipitation events. Loads of total and dissolved phosphorus were reduced by 84 and 83% (p < 0.05), and total and dissolved nitrogen by 74 and 71% (p < 0.05) with an active leaf removal program. Without leaf removal, 56% of the annual total phosphorus yield (winter excluded) was due to leaf litter in the fall compared to 16% with leaf removal. Despite significant reductions in load, total nitrogen showed only minor changes in fall yields without and with leaf removal at 19 and 16%, respectively. The majority of nutrient concentrations were in the dissolved fraction making source control through leaf removal one of the few treatment options available to environmental managers when reducing the amount of dissolved nutrients in stormwater runoff. Subsequently, the efficiency, frequency, and timing of leaf removal and street cleaning are the primary factors to consider when developing a leaf management program.

Wisconsin↗
USGS2015

Simulating the effect of climate change on stream temperature in the Trout Lake Watershed, Wisconsin

The potential for increases in stream temperature across many spatial and temporal scales as a result of climate change can pose a difficult challenge for environmental managers, especially when addressing thermal requirements for sensitive aquatic species. This study evaluates simulated changes to the thermal regime of three northern Wisconsin streams in response to a projected changing climate using a modeling framework and considers implications of thermal stresses to the fish community. The Stream Network Temperature Model (SNTEMP) was used in combination with a coupled groundwater and surface water flow model to assess forecasts in climate from six global circulation models and three emission scenarios. Model results suggest that annual average stream temperature will steadily increase approximately 1.1 to 3.2 &deg;C (varying by stream) by the year 2100 with differences in magnitude between emission scenarios. Daily mean stream temperature during the months of July and August, a period when cold-water fish communities are most sensitive, showed excursions from optimal temperatures with increased frequency compared to current conditions. Projections of daily mean stream temperature, in some cases, were no longer in the range necessary to sustain a cold water fishery.

Wisconsin↗
USGS2014

From streets to streams: Assessing the toxicity potential of urban sediment by particle size

Urban sediment can act as a transport mechanism for a variety of pollutants to move towards a receiving water body. The concentrations of these pollutants oftentimes exceed levels that are toxic to aquatic organisms. Many treatment structures are designed to capture coarse sediment but do not work well to similarly capture the fines. This study measured concentrations of select trace metals and PAHs in both the silt and sand fractions of urban sediment from four sources: stormwater bed, stormwater suspended, street dirt, and streambed. Concentrations were used to assess the toxic potential of sediment based on published sediment quality guidelines. All sources of sediment showed some level of toxic potential with stormwater bed sediment the highest followed by stormwater suspended, street dirt, and streambed. Both metal and PAH concentration distributions were highly correlated between the four sampling locations suggesting the presence of one or perhaps only a few sources of these pollutants which remain persistent as sediment is transported from street to stream. Comparison to other forms of combustion- and vehicle-related sources of PAHs revealed coal tar sealants to have the strongest correlation, in both the silt and sand fractions, at all four sampling sites. This information is important for environmental managers when selecting the most appropriate Best Management Practice (BMP) as a way to mitigate pollution conveyed in urban stormwater from source to sink.

Wisconsin↗
USGS2013

Characterizing the distribution of particles in urban stormwater: advancements through improved sampling technology

A new sample collection system was developed to improve the representation of sediment in stormwater by integrating the entire water column. The depth-integrated sampler arm (DISA) was able to mitigate sediment stratification bias in storm water, thereby improving the characterization of particle size distribution from urban source areas. Collector streets had the lowest median particle diameter of 8 &mu;m, followed by parking lots, arterial streets, feeder streets, and residential and mixed land use (32, 43, 50, 80 and 95 &mu;m, respectively). Results from this study suggest there is no single distribution of particles that can be applied uniformly to runoff in urban environments; however, integrating more of the entire water column during the sample collection can address some of the shortcomings of a fixed-point sampler by reducing variability and bias caused by the stratification of solids in a water column.

Urban Water Journal↗
USGS2013

Simulation of climate-change effects on streamflow, lake water budgets, and stream temperature using GSFLOW and SNTEMP, Trout Lake Watershed, Wisconsin

Although groundwater and surface water are considered a single resource, historically hydrologic simulations have not accounted for feedback loops between the groundwater system and other hydrologic processes. These feedbacks include timing and rates of evapotranspiration, surface runoff, soil-zone flow, and interactions with the groundwater system. Simulations that iteratively couple the surface-water and groundwater systems, however, are characterized by long run times and calibration challenges. In this study, calibrated, uncoupled transient surface-water and steady-state groundwater models were used to construct one coupled transient groundwater/surface-water model for the Trout Lake Watershed in north-central Wisconsin, USA. The computer code GSFLOW (Ground-water/Surface-water FLOW) was used to simulate the coupled hydrologic system; a surface-water model represented hydrologic processes in the atmosphere, at land surface, and within the soil-zone, and a groundwater-flow model represented the unsaturated zone, saturated zone, stream, and lake budgets. The coupled GSFLOW model was calibrated by using heads, streamflows, lake levels, actual evapotranspiration rates, solar radiation, and snowpack measurements collected during water years 1998–2007; calibration was performed by using advanced features present in the PEST parameter estimation software suite. Simulated streamflows from the calibrated GSFLOW model and other basin characteristics were used as input to the one-dimensional SNTEMP (Stream-Network TEMPerature) model to simulate daily stream temperature in selected tributaries in the watershed. The temperature model was calibrated to high-resolution stream temperature time-series data measured in 2002. The calibrated GSFLOW and SNTEMP models were then used to simulate effects of potential climate change for the period extending to the year 2100. An ensemble of climate models and emission scenarios was evaluated. Downscaled climate drivers for the period 2010–2100 showed increases in maximum and minimum temperature over the scenario period. Scenarios of future precipitation did not show a monotonic trend like temperature. Uncertainty in the climate drivers increased over time for both temperature and precipitation. Separate calibration of the uncoupled groundwater and surface-water models did not provide a representative initial parameter set for coupled model calibration. A sequentially linked calibration, in which the uncoupled models were linked by means of utility software, provided a starting parameter set suitable for coupled model calibration. Even with sequentially linked calibration, however, transmissivity of the lower part of the aquifer required further adjustment during coupled model calibration to attain reasonable parameter values for evaporation rates off a small seepage lake (a lake with no appreciable surface-water outlets) with a long history of study. The resulting coupled model was well calibrated to most types of observed time-series data used for calibration. Daily stream temperatures measured during 2002 were successfully simulated with SNTEMP; the model fit was acceptable for a range of groundwater inflow rates into the streams. Forecasts of potential climate change scenarios showed growing season length increasing by weeks, and both potential and actual evapotranspiration rates increasing appreciably, in response to increasing air temperature. Simulated actual evapotranspiration rates increased less than simulated potential evapotranspiration rates as a result of water limitation in the root zone during the summer high-evapotranspiration period. The hydrologic-system response to climate change was characterized by a reduction in the importance of the snow-melt pulse and an increase in the importance of fall and winter groundwater recharge. The less dynamic hydrologic regime is likely to result in drier soil conditions in rainfed wetlands and uplands, in contrast to less drying in groundwater-fed systems. Seepage lakes showed larger forecast stage declines related to climate change than did drainage lakes (lakes with outlet streams). Seepage lakes higher in the watershed (nearer to groundwater divides) had less groundwater inflow and thus had larger forecast declines in lake stage; however, ground-water inflow to seepage lakes in general tended to increase as a fraction of the lake budgets with lake-stage decline because inward hydraulic gradients increased. Drainage lakes were characterized by less simulated stage decline as reductions in outlet streamflow of set losses to other water flows. Net groundwater inflow tended to decrease in drainage lakes over the scenario period. Simulated stream temperatures increased appreciably with climate change. The estimated increase in annual average temperature ranged from approximately 1 to 2 degrees Celsius by 2100 in the stream characterized by a high groundwater inflow rate and 2 to 3 degrees Celsius in the stream with a lower rate. The climate drivers used for the climate-change scenarios had appreciable variation between the General Circulation Model and emission scenario selected; this uncertainty was reflected in hydrologic flow and temperature model results. Thus, as with all forecasts of this type, the results are best considered to approximate potential outcomes of climate change.

Wisconsin↗
USGS2012

Regression modeling of particle size distributions in urban stormwater: Advancements through improved sample collection methods

A new sample collection system was developed to improve the representation of sediment entrained in urban storm water by integrating water quality samples from the entire water column. The depth-integrated sampler arm (DISA) was able to mitigate sediment stratification bias in storm water, thereby improving the characterization of suspended-sediment concentration and particle size distribution at three independent study locations. Use of the DISA decreased variability, which improved statistical regression to predict particle size distribution using surrogate environmental parameters, such as precipitation depth and intensity. The performance of this statistical modeling technique was compared to results using traditional fixed-point sampling methods and was found to perform better. When environmental parameters can be used to predict particle size distributions, environmental managers have more options when characterizing concentrations, loads, and particle size distributions in urban runoff.

Wisconsin↗
USGS2011

Development of a depth-integrated sample arm to reduce solids stratification bias in stormwater sampling

A new depth-integrated sample arm (DISA) was developed to improve the representation of solids in stormwater, both organic and inorganic, by collecting a water quality sample from multiple points in the water column. Data from this study demonstrate the idea of vertical stratification of solids in storm sewer runoff. Concentrations of suspended sediment in runoff were statistically greater using a fixed rather than multi-point collection system. Median suspended sediment concentrations measured at the fixed location (near the pipe invert) were approximately double those collected using the DISA. In general, concentrations and size distributions of suspended sediment decreased with increasing vertical distance from the storm sewer invert. Coarser particles tended to dominate the distribution of solids near the storm sewer invert as discharge increased. In contrast to concentration and particle size, organic material, to some extent, was distributed homogenously throughout the water column, likely the result of its low specific density, which allows for thorough mixing in less turbulent water.

Water Environment Research↗
USGS2011

Characterizing the size distribution of particles in urban stormwater by use of fixed-point sample-collection methods

The U.S Geological Survey, in cooperation with the Wisconsin Department of Natural Resources (WDNR) and in collaboration with the Root River Municipal Stormwater Permit Group monitored eight urban source areas representing six types of source areas in or near Madison, Wis. in an effort to improve characterization of particle-size distributions in urban stormwater by use of fixed-point sample collection methods. The types of source areas were parking lot, feeder street, collector street, arterial street, rooftop, and mixed use. This information can then be used by environmental managers and engineers when selecting the most appropriate control devices for the removal of solids from urban stormwater. Mixed-use and parking-lot study areas had the lowest median particle sizes (42 and 54 (u or mu)m, respectively), followed by the collector street study area (70 (u or mu)m). Both arterial street and institutional roof study areas had similar median particle sizes of approximately 95 (u or mu)m. Finally, the feeder street study area showed the largest median particle size of nearly 200 (u or mu)m. Median particle sizes measured as part of this study were somewhat comparable to those reported in previous studies from similar source areas. The majority of particle mass in four out of six source areas was silt and clay particles that are less than 32 (u or mu)m in size. Distributions of particles ranging from <2 to >500 (u or mu)m were highly variable both within and between source areas. Results of this study suggest substantial variability in data can inhibit the development of a single particle-size distribution that is representative of stormwater runoff generated from a single source area or land use. Continued development of improved sample collection methods, such as the depth-integrated sample arm, may reduce variability in particle-size distributions by mitigating the effect of sediment bias inherent with a fixed-point sampler.

Open-File Report↗
USGS2010

Evaluation of Turf-Grass and Prairie-Vegetated Rain Gardens in a Clay and Sand Soil, Madison, Wisconsin, Water Years 2004-08

The U.S. Geological Survey, in cooperation with a consortium of 19 cities, towns, and villages in Dane County, Wis., undertook a study to compare the capability of rain gardens with different vegetative species and soil types to infiltrate stormwater runoff from the roof of an adjacent structure. Two rain gardens, one planted with turf grass and the other with native prairie species, were constructed side-by-side in 2003 at two locations with different dominant soil types, either sand or clay. Each rain garden was sized to a ratio of approximately 5:1 contributing area to receiving area and to a depth of 0.5 foot. Each rain garden, regardless of vegetation or soil type, was capable of storing and infiltrating most of the runoff over the 5-year study period. Both rain gardens in sand, as well as the prairie rain garden in clay, retained and infiltrated 100 percent of all precipitation and snowmelt events during water years 2004-07. The turf rain garden in clay occasionally had runoff exceed its confining boundaries, but was still able to retain 96 percent of all precipitation and snowmelt events during the same time period. Precipitation intensity and number of antecedent dry days were important variables that influenced when the storage capacity of underlying soils would become saturated, which resulted in pooled water in the rain gardens. Because the rooftop area that drained runoff to each rain garden was approximately five times larger than the area of the rain garden itself, evapotranspiration was a small percentage of the annual water budget. For example, during water year 2005, the maximum evapotranspiration of total influent volume ranged from 21 percent for the turf rain garden in clay to 25 percent for the turf rain garden in sand, and the minimum ranged from 12 percent for the prairie rain garden in clay to 19 percent for the prairie rain garden in sand. Little to no runoff left each rain garden as effluent and a small percentage of runoff returned to the atmosphere through evapotranspiration; therefore, the remainder was considered recharge. During water year 2005, recharge was 81 to 75 percent of total influent volume for the prairie- and turf-rain gardens in sand and 87 to 78 percent for the prairie- and turf-rain gardens in clay, respectively. Maximum recharge volumes ranged from 90 to 94 percent of the total influent volume in the turf and prairie rain gardens in sand and occurred during water year 2004. Maximum recharge in the turf and prairie rain gardens in clay ranged from 89 percent during water year 2007 to 98 percent during water year 2004. Median infiltration rates were an order of magnitude greater for rain gardens planted in sand than for those in clay, regardless of vegetation type. Under similar soil conditions, rain gardens planted with turf grass had lower median infiltration rates than those planted with prairie species. Median infiltration rates were 0.28 and 0.88 inches per hour in the turf and prairie rain gardens in clay, respectively, and 2.5 and 4.2 inches per hour in the turf and prairie rain gardens in sand, respectively. In general, infiltration rates were greater during spring (April and May) and summer (June through August) months. Of the six observed exceedences of the storage capacity of the turf rain garden in clay between April-November during 2004-07, five were predicted by use of a combination of the normalized surface storage volume, the median infiltration rate, and an estimate of specific yield for soils under the rain garden to a depth equal to the uppermost limiting layer. By use of the same criteria, in water year 2008, when the contributing drainage area to the prairie rain garden in clay was doubled, all four observed exceedences of the total storage capacity were predicted. The accuracy of the predictions of when the total storage capacity of the rain gardens would be exceeded indicates that by applying measurements of the appropriate soil properties to rain g

Scientific Investigations Report↗
USGS2009

Concentrations of polycyclic aromatic hydrocarbons (PAHs) in urban stormwater, Madison, Wisconsin, 2005–08

Concentrations of 18 PAH compounds were characterized from six urban source areas (parking lots, feeder street, collector street, arterial street, rooftop, and strip mall) around Madison, Wisconsin. Parking lots were categorized into those that were or were not sealed. On average, chrysene, fluoranthene, and pyrene were the dominant PAH compounds in all urban stormwater samples. Geometric mean concentrations for most individual PAH compounds were significantly greater for a parking lot that was sealed than for lots that were not sealed. Results from this study are consistent with similar studies that measured PAH concentrations in urban stormwater samples in Marquette, Mich., and Madison, Wis.

Wisconsin↗
USGS2008

A comparison of runoff quantity and quality from two small basins undergoing implementation of conventional- and low-impact-development (LID) strategies: Cross Plains, Wisconsin, water years 1999–2005

Environmental managers are often faced with the task of designing strategies to accommodate development while minimizing adverse environmental impacts. Low-impact development (LID) is one such strategy that attempts to mitigate environmental degradation commonly associated with impervious surfaces. The U.S. Geological Survey, in cooperation with the Wisconsin Department of Natural Resources, studied two residential basins in Cross Plains, Wis., during water years 1999–2005. A paired-basin study design was used to compare runoff quantity and quality from the two basins, one of which was developed in a conventional way and the other was developed with LID. The conventional-developed basin (herein called “conventional basin”) consisted of curb and gutter, 40-foot street widths, and a fully connected stormwater-conveyance system. The LID basin consisted of grassed swales, reduced impervious area (32-foot street widths), street inlets draining to grass swales, a detention pond, and an infiltration basin. Data collected in the LID basin represented predevelopment through near-complete build-out conditions. Smaller, more frequent precipitation events that produced stormwater discharge from the conventional basin were retained in the LID basin. Only six events with precipitation depths less than or equal to 0.4 inch produced measurable discharge from the LID basin. Of these six events, five occurred during winter months when underlying soils are commonly frozen, and one was likely a result of saturated soil from a preceding storm. In the conventional basin, the number of discharge events, using the same threshold of precipitation depth, was 180, with nearly one-half of those resulting from precipitation depths less than 0.2 inch. Precipitation events capable of producing appreciable discharge in the LID basin were typically those of high intensity or precipitation depth or those that occurred after soils were already saturated. Total annual discharge volume measured from the conventional basin ranged from 1.3 to 9.2 times that from the LID basin. Development of the LID basin did not appreciably alter the hydrologic response to precipitation characterized during predevelopment conditions. Ninety-five percent or more of precipitation in the LID basin was retained during each year of construction from predevelopment through near-complete build-out, surpassing the 90-percent benchmark established for new development by the Wisconsin Department of Natural Resources. The amount of precipitation retained in the conventional basin did not exceed 94 percent and fell below the 90-percent standard 2 of the 6 years monitored. Much of the runoff in the LID basin was retained by an infiltration basin, the largest control structure used to mitigate storm-runoff quantity and quality. The infiltration basin also was the last best-management practice (BMP) used to treat runoff before it left the LID basin as discharge. From May 25, 2002, to September 30, 2005, only 24 of 155 precipitation events exceeded the retention/ infiltrative capacity of the infiltration basin. The overall reduction in runoff volume from these few events was 51 percent. The effectiveness of the infiltration basin decreased as precipitation intensities exceeded 0.5 inch per hour. Annual loads were estimated to characterize the overall effectiveness of low-impact design practices for mitigating delivery of total solids, total suspended solids, and total phosphorus. Annual loads of these three constituents were greater in the LID basin than in the conventional basin in 2000 and 2004. Seventy percent or more of all constituent annual loads were associated with two discharge events in 2000, and a single discharge event produced 50 percent or more of constituent annual loads in 2004. Each of these discharge events was associated with considerable precipitation depths and (or) intensities, ranging from 4.89 to 6.21 inches and from 1.13 to 1.2 inches per hour, respectively. These same storms did not contribute as much of the annual load in the conventional basin. With large storms and saturated soils, the ability of low-impact design techniques to reduce runoff, and thus constituent loads, can be greatly diminished. For both the LID and conventional basins, the temperature of runoff was largely affected by ambient air temperatures. However, the temperature of discharge from the LID basin increased upon runoff cessation. This increase is likely due to solar heating of water that is temporarily stored in the detention pond and infiltration basin.

Wisconsin↗