Geology topics

William D. Stanley

Publications and source records attributed to William D. Stanley.

7 recordsLinked to original sources

USGS2012

Preliminary velocity and resistivity models of the Loma Prieta Earthquake region

A preliminary three-dimensional velocity model of the Loma Prieta epicentral region in the Santa Cruz Mountains of California has been derived using raypaths from aftershocks recorded by the U.S.G.S. seismic network. In addition, a magnetotelluric sounding profile was completed prior to the earthquake and a two-dimensional resistivity model computed. The velocity and resistivity models include a low-resistivity (3–10 ohm-m), low-velocity (3.3–5.8 km/s) wedge of material between the Zayante and San Andreas faults that extends to depths of over 8 km and is interpreted to be largely Tertiary marine sedimentary rocks. A high-resistivity (>1000 ohm-m), high-velocity (6.4–6.7 km/s) zone between the San Andreas and Sargent faults may represent largely mafic intrusive rocks.

California↗

USGS2012

Surface seismic and electrical methods to detect fluids related to faulting

In the absence of drilling, surface-based geophysical methods are necessary to observe fault zones and fault zone physical properties at seismogenic depths. These in situ physical properties can then be used to infer the presence and distribution of fluids along faults, although such observations are by nature indirect and become less exact with greater depth. Multiple observations of a range of such geophysical properties as compressional and shear seismic velocity ( V p and V s ), V p /V5 ratio (related to Poisson's ratio), resistivity and attenuation in and adjacent to fault zones offer the greatest hope of making inferences of the fault zone geometry, fluids in the fault zone, and fluid reservoirs in the surrounding crust. For simple geometries, fault zone guided waves can provide information on fault zone width and velocities for faults of the order of 200 m wide. To address the question of whether a narrow fault zone can be imaged well enough at depths of seismic rupture to infer the presence of anomalously high fluid/rock ratios, we present synthetic seismic tomography and magnetotelluric examples for an ideal case of a narrow fault zone with a simple geometry, large changes in material properties, and numerous earthquakes within the fault zone. A synthetic 0.5-km wide fault zone with 20% velocity reduction is well imaged using local earthquake tomography. When sequential velocity inversions are done, the true fault width is found, even to 9 km depth, although the calculated amplitude of the velocity reduction is lower than the actual amplitude. V p / V s is as well determined as V p . Magnetotelluric imaging of a synthetic fault zone shows that a conductive fault zone can be well imaged within the upper 10 km. Further, a narrow (1 km) very low resistivity (3 ohm m) fault core can be imaged within a broad (5 km) low resistivity (10 ohm m) fault zone, illustrating that regions of a fault containing large quantities of interconnected fluids within a broader, conductive fault zone should be detectable. Thus variations in fluid content and fluid pressure can be inferred from electrical and seismic methods but there will always be uncertainty in these inferences due to the trade-off with other factors, such as intrinsic variations in porosity, mineralogy, and pore geometry. The best approach is combined modeling of varied seismic and electrical data.

Journal of Geophysical Research Solid Earth↗

USGS2012

Tectonics and conductivity structures in the Southern Washington Cascades

The tectonic setting of the southern Washington Cascades has been studied with the aid of magnetotelluric (MT) and other geophysical data. The main feature of interest in the geophysical data is a broad high-conductivity anomaly mapped with MT and geomagnetic variation (GMV) data. This anomaly is located roughly within the triangle formed by the volcanoes Mount Rainier, Mount St. Helens, and Mount Adams but exceeds beyond Mount Rainier to the northwest. We interpret the cause of the anomaly to be conductive rocks with resistivities of 1–4 ohm m and thicknesses possibly greater than 15 km. These conductive rocks are found 2–8 km beneath the overlying less conductive volcanic and sedimentary rocks at the surface. Two aeromagnetic lows follow the trend of the conductivity anomaly, and linear belts of strike-slip seismicity are coincident with both these magnetic lows. One of the aeromagnetic lows is coincident with the western margin of the conductivity anomaly. The geophysical data appear to outline a suture zone of probable Eocene age caused by accretion of a large seamount complex (Siletzia) and that may contain large thicknesses of compressed forearc basin and accretionary prism sedimentary rocks of Cretaceous to Eocene age. Part of the shallower conductive rocks may be associated with carbonaceous continental and transitional marine sedimentary rocks of the Puget Group. The contact between the hypothesized compressed basin and the accreted terranes to the west may localize the release of shear stresses in this region of oblique subduction. Several possible explanations for the conductivity anomaly are considered in addition to the compressed basin hypothesis.

Washington↗

USGS1992

Structure of the Reelfoot rift as interpreted from 2-D magnetotelluric models

The results of magnetotelluric (MT) surveys reveal structures associated with the Reelfoot rift, including an axial high-resistivity structure that may be related to intrusions in the central part of the rift or to a previously unrecognized horst. The axis of this resistivity high generally follows the central part of the Reelfoot rift, but its orientation is offset several degrees from the enigmatic Blytheville arch. The MT structural high follows the main part of a northeast-trending seismicity belt, but in the New Madrid, Missouri area electrical structures are more complicated. In this northern part of the study area, the strike of resistivity structures determined from the MT data indicate a nearly north-south direction, rather than the N45°E direction indicated for most of the data. If the axial high-resistivity structure represents a horst, then it may form an interior divide between thick shale basins. Faults bounding the proposed horst may be a controlling factor for the northeast trending seismic zone.

Arkansas, Kentucky, Missouri, Tennessee↗

USGS1985

Regional magnetotelluric surveys in hydrocarbon exploration, Parana Basin, Brazil

The magnetotelluric geophysical method has been used effectively as a hydrocarbon exploration tool in the intracratonic Parana basin of South America. The Parana basin has an area of about 1,200,000 km 2 (463,000 mi 2 ), extending over portions of Brazil, Paraguay, Uruguay, Argentina, and Bolivia. The Paleozoic marine sedimentary rocks in the Parana basin are covered by the world's most extensive flood basalt complex, making geophysical exploration extremely difficult, although modern seismic techniques recently applied are achieving good results in some areas. The 1-2 km (3,300-6,600 ft) thick surface basalts and buried diabase sills pose no problem for the magnetotelluric method because the natural electromagnetic fields used as the energy source pass easily through the basalt. Data for the regional study were taken on six profiles with soundings spaced 8 to 15 km (5 to 9 mi) apart. The magnetotelluric sounding data outline a linear uplift known as the Ponta Grossa arch. This major structural feature cuts across the northeast-trending intracratonic basin almost perpendicularly, and is injected with numerous diabase dikes. Although its character is reasonably well known in the shallow, eastern parts of the basin, it is poorly delineated in the deeper parts of the basin where promising natural gas zones have been tested in several wells. In the survey area, MT interpretations show that basalts have aggregate thickness of as much as 2 km (6,600 ft), and basement may be as much as 6 km (20,000 ft) below the surface. Over most of the basin, the basalts are covered by Upper Cretaceous to Holocene continental sediments of a few hundred meters thickness and are underlain by 2 to 4 km (6,600 to 13,100 ft) thick Paleozoic sediments with possible hydrocarbon potential. The Ponta Grossa arch is interpreted to be the failed arm of a triple rift system that formed during the separation of the African and South American continents. Shales of the Devonian Ponta Grossa Formation are important Parana basin source rocks for hydrocarbons, as are several Permian units. Significant electrical contrasts occur between the Permian sediments and older units, so that magnetotelluric measurements can give an indication of the regional thickness of the Permian and younger sediments to aid in interpreting hydrocarbon migration patterns and possible trap areas.

Parana Basin↗

USGS1983

A practical, low-noise coil system for magnetotellurics

Magnetotellurics is a geophysical technique which was developed by Cagnaird (1953) and Tikhonov (1950) and later refined by other scientists worldwide. The technique is a method of electromagnetic sounding of the Earth and is based upon the skin depth effect in conductive media. The electric and magnetic fields arising from natural sources are measured at the surface of the earth over broad frequency bands. An excellent review of the technique is provided in the paper by Vozoff (1972). The sources of the natural fields are found in two basic mechanisms. At frequencies above a few hertz, most of the energy arises from lightning in thunderstorm belts around the equatorial regions. This energy is propagated in a wave-guide formed by the earthionospheric cavity. Energy levels are higher at fundamental modes for this cavity, but sufficient energy exists over most of the audio range to be useful for sounding at these frequencies, in which case the technique is generally referred to as audio-magnetotellurics or AMT. At frequencies lower than audio, and in general below 1 Hz, the source of naturally occuring electromagnetic energy is found in ionospheric currents. Current systems flowing in the ionosphere generate EM waves which can be used in sounding of the earth. These fields generate a relatively complete spectrum of electromagnetic energy that extends from around 1 Hz to periods of one day. Figure 1 shows an amplitude spectrum characteristic of both the ionospheric and lightning sources, covering a frequency range from 0.0001 Hz to 1000 Hz. It can be seen that there is a minimum in signal levels that occurs at about 1 Hz, in the gap between the two sources, and that signal level increases with a decrease in frequency.

Open-File Report↗

USGS1971

Resistivity sections, upper Arkansas River basin, Colorado

A reconnaissance investigation of ground-water resources in the upper Arkansas River basin from Pueblo to Leadville is being made by the U.S. Geological Survey in cooperation with the Southeastern Colorado Water Conservancy District, and the Colorado Division of Water Resources, Colorado State Engineer. As part of the investigation, surface geophysical electrical resistivity surveys were made during the summer and fall of 1970 near Buena Vista and Westcliffe, Colo. (p1.1). The resistivity surveys were made to verify a previous gravity survey and to help locate areas where ground-water supplies might be developed. This report presents the results of the surveys in the form of two resistivity sections.

Colorado↗