Geology topics

Scott Wright

Publications and source records attributed to Scott Wright.

At least 37 records · Page 2Linked to original sources

USGS2016

Long-term continuous acoustical suspended-sediment measurements in rivers - Theory, application, bias, and error

It is commonly recognized that suspended-sediment concentrations in rivers can change rapidly in time and independently of water discharge during important sediment‑transporting events (for example, during floods); thus, suspended-sediment measurements at closely spaced time intervals are necessary to characterize suspended‑sediment loads. Because the manual collection of sufficient numbers of suspended-sediment samples required to characterize this variability is often time and cost prohibitive, several “surrogate” techniques have been developed for in situ measurements of properties related to suspended-sediment characteristics (for example, turbidity, laser-diffraction, acoustics). Herein, we present a new physically based method for the simultaneous measurement of suspended-silt-and-clay concentration, suspended-sand concentration, and suspended‑sand median grain size in rivers, using multi‑frequency arrays of single-frequency side‑looking acoustic-Doppler profilers. The method is strongly grounded in the extensive scientific literature on the incoherent scattering of sound by random suspensions of small particles. In particular, the method takes advantage of theory that relates acoustic frequency, acoustic attenuation, acoustic backscatter, suspended-sediment concentration, and suspended-sediment grain-size distribution. We develop the theory and methods, and demonstrate the application of the method at six study sites on the Colorado River and Rio Grande, where large numbers of suspended-sediment samples have been collected concurrently with acoustic attenuation and backscatter measurements over many years. The method produces acoustical measurements of suspended-silt-and-clay and suspended-sand concentration (in units of mg/L), and acoustical measurements of suspended-sand median grain size (in units of mm) that are generally in good to excellent agreement with concurrent physical measurements of these quantities in the river cross sections at these sites. In addition, detailed, step-by-step procedures are presented for the general river application of the method. Quantification of errors in sediment-transport measurements made using this acoustical method is essential if the measurements are to be used effectively, for example, to evaluate uncertainty in long-term sediment loads and budgets. Several types of error analyses are presented to evaluate (1) the stability of acoustical calibrations over time, (2) the effect of neglecting backscatter from silt and clay, (3) the bias arising from changes in sand grain size, (4) the time-varying error in the method, and (5) the influence of nonrandom processes on error. Results indicate that (1) acoustical calibrations can be stable for long durations (multiple years), (2) neglecting backscatter from silt and clay can result in unacceptably high bias, (3) two frequencies are likely required to obtain sand-concentration measurements that are unbiased by changes in grain size, depending on site-specific conditions and acoustic frequency, (4) relative errors in silt-and-clay- and sand-concentration measurements decrease substantially as concentration increases, and (5) nonrandom errors may arise from slow changes in the spatial structure of suspended sediment that affect the relations between concentration in the acoustically ensonified part of the cross section and concentration in the entire river cross section. Taken together, the error analyses indicate that the two-frequency method produces unbiased measurements of suspended-silt-and-clay and sand concentration, with errors that are similar to, or larger than, those associated with conventional sampling methods.

Arizona, Texas↗

USGS2016

Long-term continuous acoustical suspended-sediment measurements in rivers – Theory, evaluation, and results from 14 stations on five rivers

We have developed a physically based method for using two acoustic frequencies to measure suspended-silt-and-clay concentration, suspended-sand concentration, and suspended-sand median grain size in river cross sections at 15-minute intervals over decadal timescales. The method is strongly grounded in the extensive scientific literature on the scattering of sound by suspensions of small particles. In particular, the method takes advantage of the specific theoretical relations among acoustic frequency, acoustic attenuation, acoustic backscatter, suspended-sediment concentration, and suspended-sediment grain-size distribution. We briefly describe the theory and methods, demonstrate the application of the method, and compute biases and errors in the method at 14 stations in the Colorado River and Rio Grande basins, where large numbers of suspended-sediment samples have been collected concurrently with acoustical measurements over many years. Quantification of errors in sediment-transport measurements made using this method is essential if the measurements are to be used effectively, e.g., to evaluate uncertainty in long-term sediment loads and budgets

Conference Paper↗

USGS2016

Sediment budgets, transport, and depositional trends in a large tidal delta

The Sacramento-San Joaquin Delta is the largest delta on the west coast of the United States. It is formed where the confluence of California’s two largest rivers (the Sacramento and San Joaquin) meet the ocean tides and has a significant physical gradient from fluvial to tidal. It is a semidiurnal system (two high and two low tides per day). Today, the Delta is one of the most manipulated in the United States. Once composed of many shallow, meandering and braided dendritic channels and dead-end sloughs and wetlands, it is now a network of leveed canals moving clear water around subsided islands. It historically has supported a biologically diverse tidal wetland complex, of which only 3% remains today (Whipple et al., 2012). It has also witnessed a collapse in the native fish populations. The Delta provides critical habitat for native species, however the hydrology and water quality are complicated by manipulations and diversions to satisfy multiple statewide objectives. Today water managers face co-equal goals of water supply to Californians and maintenance of ecosystem health and function. The Delta is a hub for both a multi-hundred-million dollar agricultural industry and a massive north-to-south water delivery system, supplying the primary source of freshwater to Central Valley farmers and drinking water for two-thirds of California’s population. Large pump facilities support the water demand and draw water from the Delta, further altering circulation patterns and redirecting the net flow toward the export facilities (Monsen et al., 2007). Fluvial sedimentation, along with organic accumulation, creates and sustains the Delta landscape. Hydraulic mining for gold in the watershed during the late 1800s delivered an especially large sediment pulse to the Delta. More recently, from 1955 to the present, a significant sediment decline has been observed that is thought to have been caused mostly by the construction of water storage reservoirs that trap the upstream sediment supply (Wright and Schoellhamer, 2004). Today, one concern is whether the volume of sediment supplied from the upper watershed is sufficient to support ecological function and sustain the Delta landscape and ecosystem in the face of climate change, sea level rise, and proposed restoration associated with the Bay Delta Conservation Plan (http://baydeltaconservationplan.com). Ecosystem health is a management focus and 150,000 acres of restoration is currently proposed, therefore it is of increasingly important to understand the quantity of sediment available for marsh and wetland restoration throughout the Bay Delta Estuary. It is also important to understand the pathways for sediment transport and the sediment budget into each of three Delta regions (figure 1) to guide restoration planning, modeling, and management.

California↗

USGS2015

Effects of human alterations on the hydrodynamics and sediment transport in the Sacramento-San Joaquin Delta, California

The Sacramento-San Joaquin Delta, California, (Delta) has been significantly altered since the mid-nineteenth century. Many existing channels have been widened or deepened and new channels have been created for navigation and water conveyance. Tidal marshes have been drained and leveed to form islands that have subsided, some of which have permanently flooded. To understand how these alterations have affected hydrodynamics and sediment transport in the Delta, we analysed measurements from 27 sites, along with other spatial data, and previous literature. Results show that: (a) the permanent flooding of islands results in an increase in the shear velocity of channels downstream, (b) artificial widening and deepening of channels generally results in a decrease in shear velocity except when the channel is also located downstream of a flooded island, (c) 1.5 Mt/year of sediment was deposited in the Delta (1997–2010), and of this deposited sediment, 0.31 Mt/year (21%) was removed through dredging.

California↗

USGS2015

Building sandbars in the Grand Canyon

In 1963, the U.S. Department of the Interior’s Bureau of Reclamation finished building Glen Canyon Dam on the Colorado River in northern Arizona, 25 kilometers upstream from Grand Canyon National Park. The dam impounded 300 kilometers of the Colorado River, creating Lake Powell, the nation’s second largest reservoir. By 1974, scientists found that the downstream river’s alluvial sandbars were eroding because the reservoir trapped the fine sediment that replenished the deposits during annual floods. These sandbars are important structures for many kinds of life in and along the river. Now, by implementing a new strategy that calls for repeated releases of large volumes of water from the dam, the U.S. Department of the Interior (DOI) seeks to increase the size and number of these sandbars. Three years into the "high-flow experiment" (HFE) protocol, the releases appear to be achieving the desired effect. Many sandbars have increased in size following each controlled flood, and the cumulative results of the first three releases suggest that sandbar declines may be reversed if controlled floods can be implemented frequently enough.

Eos, Earth and Space Science News↗

USGS2015

Assessing geomorphic change along the Trinity River downstream from Lewiston Dam, California, 1980-2011

The Trinity River Restoration Program, one of the nation’s largest adaptively managed river restoration programs, requires periodic assessment to determine the effectiveness of management actions in restoring channel dynamics and habitat features. This study documents riparian and channel changes along an intensively managed 65-kilometer reach of the Trinity River in California, downstream from Lewiston Dam. The two primary periods of interest, from 1980 to 2001 and from 2001 to 2011, are separated by a shift in restoration activities mandated by the U.S. Department of the Interior December 2000 Record of Decision. The post-2001 restoration strategy increased managed-flow releases, gravel augmentation, watershed restoration, and mechanical channel rehabilitation. We assessed the nature and extent of geomorphic change and a series of ecological performance measures (channel complexity, shoreline length, and channel–floodplain connectivity) by using a series of maps digitized from available rectified orthophotography acquired during low-flow conditions in 1980, 1997, 2001, 2006, 2009, and 2011. Lateral changes in riparian and channel features were used to quantify alluvial processes, and a review of existing streamflow, sediment, and restoration records was used to assess causal mechanisms. During the study period, natural bank erosion and mechanical rehabilitation of channel margins converted riparian features to channel features and expanded the active-channel area. The primary period of bank erosion and expansion of the active channel was from 1980 to 1997. Subsequent bar accretion from 1997 to 2001, followed by slightly greater bar scour from 2001 to 2006, took place primarily in the central and lower reaches of the study area, downstream of Indian Creek. In comparison, post‑2006 bank and bar changes were spatially limited to reaches that had sufficient local transport capacity or sediment supply supported by gravel augmentation, mechanical channel rehabilitation, and tributary contributions. The highest rates of change in the areal extents of channel and riparian features were observed during the pre‑2001 period, which was longer and relatively wetter than the post-2001 period. A series of tributary floods in 1997, 1998, and 2006 increased channel complexity and floodplain connectivity. During the post-2006 period, managed-flow releases, in the absence of tributary flooding, combined with gravel augmentation and mechanical restoration, caused localized increases in sediment supply and transport capacity that led to smaller, but measurable, increases in channel complexity and floodplain connectivity in the upper river near Lewiston Dam. Extensive pre-2001 channel widening and the muted geomorphic response of channel rehabilitation sites to post-2001 managed flows highlight the need for continued monitoring and assessment of the magnitude, duration, and timing of prescriptive flows and associated geomorphic responses.

California↗

USGS2015

Storage capacity of the Fena Valley Reservoir, Guam, Mariana Islands, 2014

The Fena Valley Reservoir is in southern Guam and is the primary source of water for the U.S. Naval Base Guam and nearby village residents. Since the construction of the Fena Dam in 1951, sediment has accumulated in the reservoir and reduced its storage capacity. The reservoir was surveyed previously in 1973, 1979, and 1990 to estimate the loss in storage capacity. To determine the current storage capacity, the U.S. Geological Survey, in cooperation with the U.S. Department of Defense Strategic Environmental Research and Development Program, surveyed the bathymetry of the reservoir in February 2014. The bathymetric survey was accomplished by making depth soundings using a boat-mounted, acoustic Doppler current profiler. Location during bathymetric data collection was determined using a single-base Global Navigation Satellite System-Real Time Kinematic survey. Vertical profiles of conductivity, temperature, and depth were collected periodically. The conductivity, temperature, and depth profiles were used to spatially and temporally adjust the sound-speed calculations used to determine depth from the soundings. Approximately 108 kilometers of transects with a total of about 380,000 depth soundings were surveyed. In addition, approximately 2,100 topographic survey points in shallow, wadable areas near the Imong River Delta were defined by using a Global Navigation Satellite System receiver attached to a fixed-length survey rod. Depth soundings and topographic survey points were compiled and interpolated to generate a digital-elevation model of the reservoir. Data extracted from the digital-elevation model were then tabulated to determine total reservoir capacity and create reservoir stage–surface area and stage–storage capacity tables. Analyses of the bathymetric data indicate that the reservoir currently has 6,915 acre-feet of storage capacity. The engineering drawings of record show that the total reservoir capacity in 1951 was estimated to be 8,365 acre-feet. Thus, between 1951 and 2014, the total storage capacity decreased by 1,450 acre-feet (a loss of 17 percent of the original total storage capacity). The remaining live-storage capacity, or the volume of storage above the lowest-level reservoir outlet elevation, was calculated to be 5,511 acre-feet in 2014, indicating a decrease of 372 acre-feet (or 6 percent) of the original 5,883 acre-feet of live-storage capacity. The remaining dead-storage capacity, or volume of storage below the lowest-level outlet, was 1,404 acre-feet in 2014, indicating a decrease of 1,078 acre-feet (or 43 percent) of the original 2,482 acre-feet of dead-storage capacity.

Scientific Investigations Report↗

USGS2015

Suspended sediment transport trough a large fluvial-tidal channel network

The confluence of the Sacramento and San Joaquin Rivers, CA, forms a large network of interconnected channels, referred to as the Sacramento-San Joaquin Delta (the Delta). The Delta comprises the transition zone from the fluvial influences of the upstream rivers and tidal influences of San Francisco Bay downstream. Formerly an extensive tidal marsh, the hydrodynamics and geomorphology of Delta have been substantially modified by humans to support agriculture, navigation, and water supply. These modifications, including construction of new channels, diking and draining of tidal wetlands, dredging of navigation channels, and the operation of large pumping facilities for distribution of freshwater from the Delta to other parts of the state, have had a dramatic impact on the physical and ecological processes within the Delta. To better understand the current physical processes, and their linkages to ecological processes, the USGS maintains an extensive network of flow, sediment, and water quality gages in the Delta. Flow gaging is accomplished through use of the index-velocity method, and sediment monitoring uses turbidity as a surrogate for suspended-sediment concentration. Herein, we present analyses of the transport and dispersal of suspended sediment through the complex network of channels in the Delta. The primary source of sediment to the Delta is the Sacramento River, which delivers pulses of sediment primarily during winter and spring runoff events. Upon reaching the Delta, the sediment pulses move through the fluvial-tidal transition while also encountering numerous channel junctions as the Sacramento River branches into several distributary channels. The monitoring network allows us to track these pulses through the network and document the dominant transport pathways for suspended sediment. Further, the flow gaging allows for an assessment of the relative effects of advection (the fluvial signal) and dispersion (from the tides) on the sediment pulses as they move through the system. Herein, we present analyses of the “first flush” sediment pulse that occurred on the Sacramento River in December 2012, documenting the transport pathways as well as the effects of advection and dispersion on the sediment as it moved through the fluvial-tidal transition in the Delta. The analyses identified an important transport pathway through the interior of the Delta toward the large pumping facilities in the south Delta, which has important implications for native fish (because their movements are triggered by sediment/turbidity). The results also reveal the dramatic transition from fluvial-dominated transport (advection) to tidal-dominated transport (dispersion) as the sediment pulse approaches the estuary.

California↗

USGS2015

Using hydrophones as a surrogate monitoring technique to detect temporal and spatial variability in bedload transport

Collecting physical bedload measurements is an expensive and time-consuming endeavor that rarely captures the spatial and temporal variability of sediment transport. Technological advances can improve monitoring of sediment transport by filling in temporal gaps between physical sampling periods. We have developed a low-cost hydrophone recording system designed to record the sediment-generated noise (SGN) resulting from collisions of coarse particles (generally larger than 4 mm) in gravel-bedded rivers. The sound level of the signal recorded by the hydrophone is assumed to be proportional to the magnitude of bedload transport as long as the acoustic frequency of the SGN is known, the grain-size distribution of the bedload is assumed constant, and the frequency band of the ambient noise is known and can be excluded from the analysis. Each system has two hydrophone heads and samples at half-hour intervals. Ten systems were deployed on the San Joaquin River, California, and its tributaries for ten months during water year 2014, and two systems were deployed during a flood event on the Gunnison River, Colorado in 2014. A mobile hydrophone system was also tested at both locations to collect longitudinal profiles of SGN. Physical samples of bedload were not collected in this study. In lieu of physical measurements, several audio recordings from each site were aurally reviewed to confirm the presence or absence of SGN, and hydraulic data were compared to historical measurements of bedload transport or transport capacity estimates to verify if hydraulic conditions during the study would likely produce bedload transport. At one site on the San Joaquin River, the threshold of movement was estimated to have occurred around 30 m 3 /s based on SGN data. During the Gunnison River flood event, continuous data showed clockwise hysteresis, indicating that bedload transport was generally less at any given streamflow discharge during the recession limb of the hydrograph. Spatial variability in transport was also detected in the longitudinal profiles audibly and using signal processing algorithms. These experiments demonstrate the ability of hydrophone technology to capture the temporal and spatial variability of sediment transport, which may be missed when samples are collected using conventional methods.

California, Colorado↗

USGS2015

Building sandbars in Grand Canyon

Now, by implementing a new strategy that calls for repeated releases of large volumes of water from the dam, the U.S. Department of the Interior seeks to increase the size and number of these sandbars. Three years into the “High Flow Experiment” protocol, the releases appear to be achieving the desired effect. Many sandbars have increased in size following each controlled flood and the cumulative results of the first three releases suggests that sandbar declines may be reversed if controlled floods can be implemented frequently enough.

Boatman's Quarterly Review↗

USGS2014

Physically based method for measuring suspended-sediment concentration and grain size using multi-frequency arrays of acoustic-doppler profilers

As the result of a 12-year program of sediment-transport research and field testing on the Colorado River (6 stations in UT and AZ), Yampa River (2 stations in CO), Little Snake River (1 station in CO), Green River (1 station in CO and 2 stations in UT), and Rio Grande (2 stations in TX), we have developed a physically based method for measuring suspended-sediment concentration and grain size at 15-minute intervals using multifrequency arrays of acoustic-Doppler profilers. This multi-frequency method is able to achieve much higher accuracies than single-frequency acoustic methods because it allows removal of the influence of changes in grain size on acoustic backscatter. The method proceeds as follows. (1) Acoustic attenuation at each frequency is related to the concentration of silt and clay with a known grain-size distribution in a river cross section using physical samples and theory. (2) The combination of acoustic backscatter and attenuation at each frequency is uniquely related to the concentration of sand (with a known reference grain-size distribution) and the concentration of silt and clay (with a known reference grain-size distribution) in a river cross section using physical samples and theory. (3) Comparison of the suspended-sand concentrations measured at each frequency using this approach then allows theory-based calculation of the median grain size of the suspended sand and final correction of the suspended-sand concentration to compensate for the influence of changing grain size on backscatter. Although this method of measuring suspended-sediment concentration is somewhat less accurate than using conventional samplers in either the EDI or EWI methods, it is much more accurate than estimating suspended-sediment concentrations using calibrated pump measurements or single-frequency acoustics. Though the EDI and EWI methods provide the most accurate measurements of suspended-sediment concentration, these measurements are labor-intensive, expensive, and may be impossible to collect at time intervals less than discharge-independent changes in suspended-sediment concentration can occur (< hours). Therefore, our physically based multi-frequency acoustic method shows promise as a cost-effective, valid approach for calculating suspended-sediment loads in river at a level of accuracy sufficient for many scientific and management purposes.

Conference Paper↗

USGS2013

Adjustment of the San Francisco estuary and watershed to decreasing sediment supply in the 20th century

The general progression of human land use is an initial disturbance (e.g., deforestation, mining, agricultural expansion, overgrazing, and urbanization) that creates a sediment pulse to an estuary followed by dams that reduce sediment supply. We present a conceptual model of the effects of increasing followed by decreasing sediment supply that includes four sequential regimes, which propagate downstream: a stationary natural regime, transient increasing sediment supply, transient decreasing sediment supply, and a stationary altered regime. The model features characteristic lines that separate the four regimes. Previous studies of the San Francisco Estuary and watershed are synthesized in the context of this conceptual model. Hydraulic mining for gold in the watershed increased sediment supply to the estuary in the late 1800s. Adjustment to decreasing sediment supply began in the watershed and upper estuary around 1900 and in the lower estuary in the 1950s. Large freshwater flow in the late 1990s caused a step adjustment throughout the estuary and watershed. It is likely that the estuary and watershed are still capable of adjusting but further adjustment will be as steps that occur only during greater floods than previously experienced during the adjustment period. Humans are actively managing the system to try to prevent greater floods. If this hypothesis of step changes occurring for larger flows is true, then the return interval of step changes will increase or, if humans successfully control floods in perpetuity, there will be no more step changes.

California↗

USGS2013

A sediment budget for the southern reach in San Francisco Bay, CA: Implications for habitat restoration

The South Bay Salt Pond Restoration Project is overseeing the restoration of about 6000 ha of former commercial salt-evaporation ponds to tidal marsh and managed wetlands in the southern reach of San Francisco Bay (SFB). As a result of regional groundwater overdrafts prior to the 1970s, parts of the project area have subsided below sea-level and will require between 29 and 45 million m 3 of sediment to raise the surface of the subsided areas to elevations appropriate for tidal marsh colonization and development. Therefore, a sufficient sediment supply to the far south SFB subembayment is a critical variable for achieving restoration goals. Although both major tributaries to far south SFB have been seasonally gaged for sediment since 2004, the sediment flux at the Dumbarton Narrows, the bayward boundary of far south SFB, has not been quantified until recently. Using daily suspended-sediment flux data from the gages on Guadalupe River and Coyote Creek, combined with continuous suspended-sediment flux data at Dumbarton Narrows, we computed a sediment budget for far south SFB during Water Years 2009–2011. A Monte Carlo approach was used to quantify the uncertainty of the flux estimates. The sediment flux past Dumbarton Narrows from the north dominates the input to the subembayment. However, environmental conditions in the spring can dramatically influence the direction of springtime flux, which appears to be a dominant influence on the net annual flux. It is estimated that up to several millennia may be required for natural tributary sediments to fill the accommodation space of the subsided former salt ponds, whereas supply from the rest of the bay could fill the space in several centuries. Uncertainty in the measurement of sediment flux is large, in part because small suspended-sediment concentration differences between flood and ebb tides can lead to large differences in total mass exchange. Using Monte Carlo simulations to estimate the random error associated with this uncertainty provides a more statistically rigorous method of quantifying this uncertainty than the more typical “sum of errors” approach. The results of this study reinforce the need for measurement of estuarine sediment fluxes over multiple years (multiple hydrologic conditions) to adequately detail the variability in flux. Additionally, the timing of breaching events for the restoration project could be tied to annual hydrologic conditions to capitalize on increased regional sediment supply.

California↗

USGS2013

The use of modeling and suspended sediment concentration measurements for quantifying net suspended sediment transport through a large tidally dominated inlet

Sediment exchange at large energetic inlets is often difficult to quantify due complex flows, massive amounts of water and sediment exchange, and environmental conditions limiting long-term data collection. In an effort to better quantify such exchange this study investigated the use of suspended sediment concentrations (SSC) measured at an offsite location as a surrogate for sediment exchange at the tidally dominated Golden Gate inlet in San Francisco, CA. A numerical model was calibrated and validated against water and suspended sediment flux measured during a spring–neap tide cycle across the Golden Gate. The model was then run for five months and net exchange was calculated on a tidal time-scale and compared to SSC measurements at the Alcatraz monitoring site located in Central San Francisco Bay ~ 5 km from the Golden Gate. Numerically modeled tide averaged flux across the Golden Gate compared well (r 2 = 0.86, p-value < 0.05) with 25 h low-pass filtered (tide averaged) SSCs measured at Alcatraz over the five month simulation period (January through April 2008). This formed a basis for the development of a simple equation relating the advective flux at Alcatraz with suspended sediment flux across the Golden Gate. Utilization of the equation with all available Alcatraz SSC data resulted in an average export rate of 1.2 Mt/yr during water years 2004 through 2010. While the rate is comparable to estimated suspended sediment inflow rates from sources within the Bay over the same time period (McKee et al., 2013-this issue), there was little variation from year to year. Exports were computed to be greatest during the wettest water year analyzed but only marginally so.

California↗

USGS2013

Hydraulic and Geomorphic Assessment of the Merced River and Historic Bridges in Eastern Yosemite Valley, Yosemite National Park, California: Sacramento, California

The Merced River in the popular and picturesque eastern-most part of Yosemite Valley in Yosemite National Park, California, USA, has been extensively altered since the park was first conceived in 1864. Historical human trampling of streambanks has been suggested as the cause of substantial increases in stream width, and the construction of undersized stone bridges in the 1920s has been suggested as the major factor leading to an increase in overbank flooding due to deposition of bars and islands between the bridges. In response, the National Park Service at Yosemite National Park (YNP) requested a study of the hydraulic and geomorphic conditions affecting the most-heavily influenced part of the river, a 2.4-km reach in eastern Yosemite Valley extending from above the Tenaya Creek and Merced River confluence to below Housekeeping Bridge. As part of the study, present-day conditions were compared to historical conditions and several possible planning scenarios were investigated, including the removal of an elevated road berm and the removal of three undersized historic stone bridges identified by YNP as potential problems: Sugar Pine, Ahwahnee and Stoneman Bridges. This Open-File Report will be superseded at a later date by a Scientific Investigations Report. A two-dimensional hydrodynamic model, the USGS FaSTMECH (Flow and Sediment Transport with Morphological Evolution of Channels) model, within the USGS International River Interface Cooperative (iRIC) model framework, was used to compare the scenarios over a range of discharges with annual exceedance probabilities of 50-, 20-, 10-, and 5- percent. A variety of topographic and hydraulic data sources were used to create the input conditions to the hydrodynamic model, including aerial LiDAR (Light Detection And Ranging), ground-based LiDAR, total station survey data, and grain size data from pebble counts. A digitized version of a historical topographic map created by the USGS in 1919, combined with estimates of grain size, was used to simulate historical conditions, and the planning scenarios were developed by altering the present-day topography. Roughness was estimated independently of measured water-surface elevations by using the mapped grain-size data and the Keulegan relation of grain size to drag coefficient. The FaSTMECH hydrodynamic model was evaluated against measured water levels by using a 130.9 m 3 s -1 flow (approximately a 33-percent annual exceedance probability flood) with 36 water-surface elevations measured by YNP personnel on June 8, 2010. This evaluation run had a root mean square error of 0.21 m between the simulated- and observed water-surface elevations (less than 10 percent of depth), though the observed water-surface elevations had relatively high variation due to the strong diurnal stage changes over the course of the 4.4-hour collection period, during which discharge varied by about 15 percent. There are presently no velocity data with which to test the model. A geomorphic assessment was performed that consisted of an estimate of the magnitude and frequency of bedload and suspended-sediment transport at “Tenaya Bar”, an important gravel-cobble bar located near the upstream end of the study site that determines the amount of flow across the floodplain at the Sugar Pine – Ahwahnee bend. An analysis of select repeat cross-sections collected by YNP since the late 1980s was done to investigate changes in channel cross-sectional area near the Tenaya Bar site. The results of the FaSTMECH models indicate that the maximum velocities in the present-day channel within the study reach are associated with Stoneman and Sugar Pine Bridges, at close to 3.0 m s -1 for the 5-percent annual exceedance probability flood. The modeled maximum velocities at Ahwahnee Bridge are comparatively low, at between 1.5 and 2.0 m s -1 , most likely due to the bridge's orientation parallel to down-valley floodplain flows. The results of the FaSTMECH models for the bridge removal scenarios indicate a reduction in average velocity at the bridge sites for the range of flows by approximately 23-38 percent (Sugar Pine Bridge), 32-42 percent (Ahwahnee Bridge), and 33-39 percent (Stoneman Bridge), though a side channel of concern to YNP management did not appear to be substantially affected by the removal scenarios. In comparison to the historical data, the FaSTMECH results suggest that flows for present-day conditions do not inundate the floodplain until between the 50- and 20-percent annual exceedance probability flood, whereas historically, a large portion of the floodplain was inundated during the 50-percent annual exceedance probability flood. Modeled maximum velocities in the present-day channel commonly exceed 2.0 m s -1 , whereas with the historical scenario, modeled maximum in-channel velocities rarely exceeded 2.0 m s -1 . The geomorphic analysis of the magnitude-frequency of bedload and suspended-sediment transport suggests that at the important Tenaya Bar site, the majority of bed sediment is mobile during most snowmelt-dominated floods. In contrast to sediment transport capacity, the analysis of repeat cross-sections suggests that bedload sediment supply into the eastern Yosemite Valley may be quite different between rain-on-snow floods and snowmelt-dominated floods, potentially with most sediment supply occurring during rain-on-snow floods, such as the 1997 flood. In contrast, the magnitude-frequency analysis of bedload and suspended-sediment transport suggests that long-term bedload sediment transport is likely dominated by snowmelt floods, and suspended-sediment transport is relatively low compared to bedload transport. Obtaining measured velocity data throughout the study reach would aid in model calibration, and thus would improve confidence in model results. Improved confidence in the model velocity results would allow additional substantial analyses of reach-scale effects of the planning scenarios and would enable the development of geomorphic models to evaluate the long-term geomorphic responses of the site. In addition, the collection of watershed sediment-supply data, about which little is presently known, would give planners helpful tools to plan restoration scenarios for this nationally important river.

California↗

USGS2012

Conceptual model of sedimentation in the Sacramento-San Joaquin River Delta

Sedimentation in the Sacramento–San Joaquin River Delta builds the Delta landscape, creates benthic and pelagic habitat, and transports sediment-associated contaminants. Here we present a conceptual model of sedimentation that includes submodels for river supply from the watershed to the Delta, regional transport within the Delta and seaward exchange, and local sedimentation in open water and marsh habitats. The model demonstrates feedback loops that affect the Delta ecosystem. Submerged and emergent marsh vegetation act as ecosystem engineers that can create a positive feedback loop by decreasing suspended sediment, increasing water column light, which in turn enables more vegetation. Sea-level rise in open water is partially countered by a negative feedback loop that increases deposition if there is a net decrease in hydrodynamic energy. Manipulation of regional sediment transport is probably the most feasible method to control suspended sediment and thus turbidity. The conceptual model is used to identify information gaps that need to be filled to develop an accurate sediment transport model.

Sacramento-San Joaquin Delta↗

USGS2011

Flow structures and sandbar dynamics in a canyon river during a controlled flood, Colorado River, Arizona

In canyon rivers, debris fan constrictions create rapids and downstream pools characterized by secondary flow structures that are closely linked to channel morphology. In this paper we describe detailed measurements of the three‐dimensional flow structure and sandbar dynamics of two pools along the Colorado River in the Grand Canyon during a controlled flood release from Glen Canyon Dam. Results indicate that the pools are characterized by large lateral recirculation zones (eddies) resulting from flow separation downstream from the channel constrictions, as well as helical flow structures in the main channel and eddy. The lateral recirculation zones are low‐velocity areas conducive to fine sediment deposition, particularly in the vicinity of the separation and reattachment points and are thus the dominant flow structures controlling sandbar dynamics. The helical flow structures also affect morphology but appear secondary in importance to the lateral eddies. During the controlled flood, sandbars in the separation and reattachment zones at both sites tended to build gradually during the rising limb and peak flow. Deposition in shallow water on the sandbars was accompanied by erosion in deeper water along the sandbar slope at the interface with the main channel. Erosion occurred via rapid mass failures as well as by gradual boundary shear stress driven processes. The flow structures and morphologic links at our study sites are similar to those identified in other river environments, in particular sharply curved meanders and channel confluences where the coexistence of lateral recirculation and helical flows has been documented.

Journal of Geophysical Research F: Earth Surface↗

USGS2011

Three experimental high-flow releases from Glen Canyon Dam, Arizona— Effects on the downstream Colorado River ecosystem

Three high-flow experiments (HFEs) were conducted by the U.S. Department of the Interior at Glen Canyon Dam, Arizona, in March 1996, November 2004, and March 2008. Also known as artificial or controlled floods, these scheduled releases of water above the dam's powerplant capacity were designed to mimic pre-dam seasonal flooding on the Colorado River. The goal of the HFEs was to determine whether high flows could be used to benefit important downstream resources in Glen Canyon National Recreation Area and Grand Canyon National Park that have been affected by the existence and operation of Glen Canyon Dam. These downstream resources include native fish, particularly endangered humpback chub (Gila cypha), terrestrial and aquatic sandbar habitats, cultural sites, and recreational resources. This Fact Sheet summarizes HFE-related studies published since 1996 and outlines a possible strategy for implementing future HFEs.

Arizona↗