Geology Reports⌕ Search

Geology topics

S. Maurice

Publications and source records attributed to S. Maurice.

At least 19 recordsLinked to original sources
USGS2026

Corundum discovered by SuperCam and the Perseverance rover at Jezero crater, Mars

Mars is primarily composed of mafic mineral assemblages and their alteration products, but small, scattered rocks strewn across the landscape offer clues to greater petrological diversity. While traversing the Jezero crater rim, the Perseverance rover encountered several plagioclase-rich light-toned float rocks. SuperCam identified the distinctive signature of corundum (α-Al 2 O 3 ) in these rocks using time-resolved luminescence spectroscopy. Two strong peaks (692.7 and 694.1 nm) with millisecond lifetimes, and additional supporting lines, are consistent with Cr 3+ substitution for Al 3+ in corundum. Corundum forms in Al-rich, Si-depleted environments through magmatic or metamorphic processes. Given the rocks' small size, association with plagioclase, and location on the crater rim, we interpret the most plausible formation scenario to be impact induced metamorphism at the interface of a felsic and a mafic/ultramafic member with the likely action of fluids at some stage, although other possibilities are not excluded.

Geophysical Research Letters↗
USGS2025

From hydrated silica to quartz: Potential hydrothermal precipitates found in Jezero crater, Mars

On Earth, silica-rich phases from opal to quartz are important indicators and tracers of geological processes. Hydrated silica, such as opal, is a particularly good matrix for the preservation of molecular and macroscopic biosignatures. Cherts, a type of silica-dominated rocks, provide a unique archive of ancient terrestrial life while quartz is the emblematic mineral of the Earth's continental crust. On Mars, hydrated silica has been detected in several locations based on remote sensing and rover-based studies. In the present article we report on the detection of cobbles made of hydrated silica (opal or chalcedony), as well as well-crystallized quartz. These detections were made with the SuperCam instrument onboard Perseverance (Mars 2020 mission), using a combination of LIBS, infrared and Raman spectroscopy. Quartz-dominated stones are detected unambiguously for the first time on the Martian surface, and based on grain size and crystallinity are proposed to be of hydrothermal origin. Although these rocks were all found as float, we propose that these detections are part of a common hydrothermal system, and represent different depths / temperatures of precipitation. This attests that hydrothermal processes were active in and around Jezero crater, possibly triggered by the Jezero crater-forming impact. These silica-rich rocks, in particular opaline silica, are very promising targets for sampling and return to Earth given their high biosignature preservation potential.

Earth and Planetary Science Letters↗
USGS2025

Ultramafic float rocks at Jezero crater (Mars): Excavation of lower crustal rocks or mantle peridotites by impact cratering?

Based on observation and data from meteorites and in situ scientific missions, experiments as well as models, the Martian mantle is assumed to share some compositional and mineralogical affinity with the terrestrial mantle. However, there might be subtle differences like the Martian mantle being more ferroan. Yet, we do not have any direct analysis of a Martian mantle rock to confirm this assumption. NASA’s Perseverance rover found olivine-rich boulder-sized float rocks on the upper Jezero fan (Mars). These boulders have an ultramafic composition and their mineralogy is dominantly composed of Fo 73±3 olivine with high-Mg orthopyroxene, Cr-rich Ti-Fe oxides and minor plagioclase and high-Ca pyroxene. Microtextural and petrological analysis reveals that these minerals crystallized at equilibrium. In addition, these boulders are different from all the bedrocks analyzed by Perseverance along its traverse which are crustal igneous rocks and sediments. Comparing our data to Martian meteorites and available Mars bulk silicate models (BSM), we discuss that these boulders could represent primitive melts and/or lower crustal material, and we specifically hypothesize that they could be mantle peridotites. We propose that these putative mantle rocks could have been excavated by the succession of impacts from the shallow mantle or lower crust in the Isidis region where Jezero crater is located. These olivine-rich boulders could thereby constitute the first direct analysis of a Martian mantle rock.

Earth and Planetary Science Letters↗
USGS2025

Ageing of organic materials at the surface of Mars: A Raman study aboard Perseverance

The Perseverance rover is exploring Jezero crater on Mars, one of its goals being to collect samples to be returned to Earth to search for organic remains of ancient Martian life. However, the organic content of these rocks has likely suffered from the radiation environment on the surface of Mars to an extent yet to be quantified. For the first time, a 1000 sols long ageing experiment was conducted at the surface of Mars, i.e. under actual Martian conditions, relying on the 100 % organic Ertalyte target carried by Perseverance. White at landing, the Ertalyte target has turned brown with time, while its Raman signal changed, with a modification of the background (its maximum has shifted from 1500 to 2000 cm −1 ) and a reduction of the contribution of the Raman signal of Ertalyte (by a factor of 5 over the first 500 sols). Given the intrinsic resistance of the Ertalyte to UV exposure, which is not anticipated for most Martian organic materials, these results suggest that exposure at the surface of Mars will make the detection of Martian organic molecules challenging.

Geochemical Perspectives Letters↗
USGS2024

Intense alteration on early Mars revealed by high-aluminum rocks at Jezero Crater

The NASA Perseverance rover discovered light-toned float rocks scattered across the surface of Jezero crater that are particularly rich in alumina ( ~ 35 wt% Al 2 O 3 ) and depleted in other major elements (except silica). These unique float rocks have heterogeneous mineralogy ranging from kaolinite/halloysite-bearing in hydrated samples, to spinel-bearing in dehydrated samples also containing a dehydrated Al-rich phase. Here we describe SuperCam and Mastcam-Z observations of the float rocks, including the first in situ identification of kaolinite or halloysite on another planet, and dehydrated phases including spinel and apparent partially dehydroxylated kaolinite. The presence of spinel in these samples is likely detrital in origin, surviving kaolinitization, pointing to an ultramafic origin. However, the association of low hydration with increased Al 2 O 3 abundances suggests heating-induced dehydration which could have occurred during the lithification or impact excavation of these rocks. Given the orbital context of kaolinite-bearing megabreccia in the Jezero crater rim, we propose an origin for these rocks involving intense aqueous alteration of the parent material, followed by dehydration/lithification potentially through impact processes, and dispersion into Jezero crater through flood or impact-related processes.

Communications Earth & Environment↗
USGS2022

The distribution of clay minerals and their impact on diagenesis in Glen Torridon, Gale crater, Mars

Glen Torridon (GT) is a recessive-trough feature on the northwestern slope of “Mt. Sharp” in Gale crater, Mars with the highest Fe-/Mg-phyllosilicates abundances detected by the Curiosity rover to date. Understanding the origin of these clay minerals and their relationship with diagenetic processes is critical for reconstructing the nature and habitability of past surface and subsurface environments in Gale crater. We aim to constrain the distribution and extent of diagenesis using compositional and morphological trends observed by visible-to-near infrared reflectance spectra in GT from Mastcam and ChemCam, supported by high-resolution images from the Mars Hand Lens Imager. Spectral features consistent with nontronite and fine-grained red hematite are ubiquitous throughout lower GT, and are strongest where diagenetic features are limited, suggesting that both were formed early, before burial. Diagenetic features increase in both abundance and diversity farther up-section, and we observe morphologic evidence for multiple episodes of diagenesis, with the edge of a diagenetic front partially preserved in the middle stratigraphic member, Knockfarril Hill. Near the contact between GT and the overlying Greenheugh pediment capping unit, we observe a lack of clay minerals with signatures consistent instead with coarse-grained gray hematite, likely formed through late-diagenetic alteration. We hypothesize that the sandstone-dominant Stimson formation acted as a conduit for diagenetic fluid flow into the area and that the clay-rich impermeable GT slowed the flow of those fluids, leading to enhanced alteration surrounding the clay-rich portions of GT, including within the nearby Vera Rubin ridge.

JGR Planets↗
USGS2022

Aqueously altered igneous rocks sampled on the floor of Jezero crater, Mars

The Perseverance rover landed in Jezero crater, Mars, to investigate ancient lake and river deposits. We report observations of the crater floor, below the crater’s sedimentary delta, finding the floor consists of igneous rocks altered by water. The lowest exposed unit, informally named Séítah, is a coarsely crystalline olivine-rich rock, which accumulated at the base of a magma body. Fe-Mg carbonates along grain boundaries indicate reactions with CO 2 -rich water, under water-poor conditions. Overlying Séítah is a unit informally named Máaz, which we interpret as lava flows or the chemical complement to Séítah in a layered igneous body. Voids in these rocks contain sulfates and perchlorates, likely introduced by later near-surface brine evaporation. Core samples of these rocks were stored aboard Perseverance for potential return to Earth.

Science↗
USGS2021

Alternating wet and dry depositional environments recorded in the stratigraphy of Mt Sharp at Gale Crater, Mars

The Curiosity rover is exploring Hesperian-aged stratigraphy in Gale crater, Mars, where a transition from clay-bearing units to a layered sulfate-bearing unit has been interpreted to represent a major environmental transition of unknown character. We present the first description of key facies in the sulfate-bearing unit, recently observed in the distance by the rover, and propose a model for changes in depositional environments. Our results indicate a transition from lacustrine mudstones into thick aeolian deposits, topped by a major deflation surface, above which strata show architectures likely diagnostic of a subaqueous environment. This model offers a reference example of a depositional sequence for layered sulfate-bearing strata, which have been identified from orbit in other locations globally. It differs from the idea of a monotonic Hesperian climate change into long-term aridity on Mars and instead implies a period characterized by multiple transitions between sustained drier and wetter climates.

Geology↗
USGS2021

Improving ChemCam LIBS long-distance elemental compositions using empirical abundance trends

The ChemCam instrument on the Curiosity rover provides chemical compositions of Martian rocks and soils using remote laser-induced breakdown spectroscopy (LIBS). The elemental calibration is stable as a function of distance for Ti, Fe, Mg, and Ca. The calibration shows small, systematically increasing abundance trends as a function of distance for Al, Na, K, and to some extent, Si. The distance effect is known to be due to a dependence with distance on the relative strengths of atomic transition lines. Emission lines representing transitions from relatively low energy levels remain intense at longer distances while emission lines representing transitions from higher energy levels decrease in intensity more rapidly as a function of distance. The multivariate algorithms used to determine elemental compositions rely on a large number of emission lines in many cases, so rather than trying to correct all emission lines, a study was made of the predicted compositions as a function of distance, in order to determine an empirical correction. Abundance trends can be well approximated by a linear trend with distance within the ranges of abundances and distances observed up to ~6 m. Data from 11 distinct geological members and data groups of the Murray formation in Gale crater, Mars, were used to form the model, selecting the members and data groups yielding the best statistics. The model was tested using data from several targets observed from two different distances, and using data from the Kimberley formation, the composition of which is significantly different from the Murray formation, showing that the model works on other compositions beyond those used to build the model. For long-distance observations up to ~6 m, corrections can be made back to an equivalent composition at the median distance of ChemCam observations (2.6 m). The model has been validated up to 6.2 m, although ChemCam is able to observe bedrock targets to >7 m, and iron meteorites to distances of >9 m.

Spectrochimica Acta Part B: Atomic Spectroscopy↗
USGS2015

Chemical variations in Yellowknife Bay formation sedimentary rocks analyzed by ChemCam on board the Curiosity rover on Mars

The Yellowknife Bay formation represents a ~5 m thick stratigraphic section of lithified fluvial and lacustrine sediments analyzed by the Curiosity rover in Gale crater, Mars. Previous works have mainly focused on the mudstones that were drilled by the rover at two locations. The present study focuses on the sedimentary rocks stratigraphically above the mudstones by studying their chemical variations in parallel with rock textures. Results show that differences in composition correlate with textures and both manifest subtle but significant variations through the stratigraphic column. Though the chemistry of the sediments does not vary much in the lower part of the stratigraphy, the variations in alkali elements indicate variations in the source material and/or physical sorting, as shown by the identification of alkali feldspars. The sandstones contain similar relative proportions of hydrogen to the mudstones below, suggesting the presence of hydrous minerals that may have contributed to their cementation. Slight variations in magnesium correlate with changes in textures suggesting that diagenesis through cementation and dissolution modified the initial rock composition and texture simultaneously. The upper part of the stratigraphy (~1 m thick) displays rocks with different compositions suggesting a strong change in the depositional system. The presence of float rocks with similar compositions found along the rover traverse suggests that some of these outcrops extend further away in the nearby hummocky plains.

Journal of Geophysical Research E: Planets↗
USGS2015

ChemCam results from the Shaler outcrop in Gale crater, Mars

The ChemCam campaign at the fluvial sedimentary outcrop “Shaler” resulted in observations of 28 non-soil targets, 26 of which included active laser induced breakdown spectroscopy (LIBS), and all of which included Remote Micro-Imager (RMI) images. The Shaler outcrop can be divided into seven facies based on grain size, texture, color, resistance to erosion, and sedimentary structures. The ChemCam observations cover Facies 3 through 7. For all targets, the majority of the grains were below the limit of the RMI resolution, but many targets had a portion of resolvable grains coarser than ∼0.5 mm. The Shaler facies show significant scatter in LIBS spectra and compositions from point to point, but several key compositional trends are apparent, most notably in the average K 2 O content of the observed facies. Facies 3 is lower in K 2 O than the other facies and is similar in composition to the “snake,” a clastic dike that occurs lower in the Yellowknife Bay stratigraphic section. Facies 7 is enriched in K 2 O relative to the other facies and shows some compositional and textural similarities to float rocks near Yellowknife Bay. The remaining facies (4, 5, and 6) are similar in composition to the Sheepbed and Gillespie Lake members, although the Shaler facies have slightly elevated K 2 O and FeO T . Several analysis points within Shaler suggest the presence of feldspars, though these points have excess FeO T which suggests the presence of Fe oxide cement or inclusions. The majority of LIBS analyses have compositions which indicate that they are mixtures of pyroxene and feldspar. The Shaler feldspathic compositions are more alkaline than typical feldspars from shergottites, suggesting an alkaline basaltic source region, particularly for the K 2 O-enriched Facies 7. Apart from possible iron-oxide cement, there is little evidence for chemical alteration at Shaler, although calcium-sulfate veins comparable to those observed lower in the stratigraphic section are present. The differing compositions, and inferred provenances at Shaler, suggest compositionally heterogeneous terrain in the Gale crater rim and surroundings, and intermittent periods of deposition.

Icarus↗
USGS2014

Chemistry and texture of the rocks at Rocknest, Gale Crater: Evidence for sedimentary origin and diagenetic alteration

A suite of eight rocks analyzed by the Curiosity Rover while it was stopped at the Rocknest sand ripple shows the greatest chemical divergence of any potentially sedimentary rocks analyzed in the early part of the mission. Relative to average Martian soil and to the stratigraphically lower units encountered as part of the Yellowknife Bay formation, these rocks are significantly depleted in MgO, with a mean of 1.3 wt %, and high in Fe, averaging over 20 wt % FeOT, with values between 15 and 26 wt % FeOT. The variable iron and low magnesium and rock texture make it unlikely that these are igneous rocks. Rock surface textures range from rough to smooth, can be pitted or grooved, and show various degrees of wind erosion. Some rocks display poorly defined layering while others seem to show possible fractures. Narrow vertical voids are present in Rocknest 3, one of the rocks showing the strongest layering. Rocks in the vicinity of Rocknest may have undergone some diagenesis similar to other rocks in the Yellowknife Bay Formation as indicated by the presence of soluble calcium phases. The most reasonable scenario is that fine-grained sediments, potentially a mixture of feldspar-rich rocks from Bradbury Rise and normal Martian soil, were lithified together by an iron-rich cement.

Journal of Geophysical Research E: Planets↗
USGS2014

The rock abrasion record at Gale Crater: Mars Science Laboratory results from Bradbury Landing to Rocknest

Ventifacts, rocks abraded by wind-borne particles, are found in Gale Crater, Mars. In the eastward drive from “Bradbury Landing” to “Rocknest,” they account for about half of the float and outcrop seen by Curiosity's cameras. Many are faceted and exhibit abrasion textures found at a range of scales, from submillimeter lineations to centimeter-scale facets, scallops, flutes, and grooves. The drive path geometry in the first 100 sols of the mission emphasized the identification of abrasion facets and textures formed by westerly flow. This upwind direction is inconsistent with predictions based on models and the orientation of regional dunes, suggesting that these ventifact features formed from very rare high-speed winds. The absence of active sand and evidence for deflation in the area indicates that most of the ventifacts are fossil features experiencing little abrasion today.

Journal of Geophysical Research E: Planets↗
USGS2014

Igneous mineralogy at Bradbury Rise: the first ChemCam campaign at Gale crater

Textural and compositional analyses using ChemCam Remote Micro Imager (RMI) and Laser Induced Breakdown Spectroscopy (LIBS) have been performed on 5 float rocks and coarse gravels along the first 100 meters of the Curiosity traverse at Bradbury rise. ChemCam, the first LIBS instrument sent to another planet, offers the opportunity to assess mineralogic diversity at grain-size scales (∼100μm) and, from this, lithologic diversity. Depth profiling indicates that targets are relatively free of surface coatings. One type of igneous rock is volcanic and includes both aphanitic (Coronation) and porphyritic (Mara) samples. The porphyritic sample shows dark grains that are likely pyroxene megacrysts in a finegrained mesostasis containing andesine needles. Both types have magnesium-poor basaltic compositions and in this respect are similar to the evolved Jake-Matijevic rock [Stolper et al., 2013] analyzed further along the Curiosity traverse both with APXS and ChemCam instruments. The second rock-type encountered is a coarse-grained intrusive rock (Thor Lake) showing equigranular texture with mm size crystals of feldspars and Fe-Ti oxides. Such a rock is not unique at Gale as the surrounding coarse gravels (such as Beaulieu) and the conglomerate Link are dominated by feldspathic (andesine-bytownite) clasts. Finally, alkali feldspar compositions associated with a silica polymorph have been analyzed in fractured filling material of Preble rock and in Stark, a putative pumice or an impact melt. These observations document magmatic diversity at Gale and describe the first fragments of feldspar-rich lithologies (possibly an anorthosite) that may be ancient crust transported from the crater rim and now forming float rocks, coarse gravel or conglomerate clasts.

Journal of Geophysical Research E: Planets↗
USGS2014

ChemCam results from the Shaler Outcrop in Gale Crater, Mars

The "Shaler" outcrop in Gale crater is approximately 0.7 m thick and >20 m long, and exhibits multiple well-exposed platy and cross-stratified facies [1] interpreted to be primarily fluvial sandstone deposits. The outcrop is a part of the upper Glenelg member in the Yellowknife Bay (YKB) stratigraphic section [2]. Curiosity first encountered the "Shaler" outcrop on sol 121 of the mission, and returned to the outcrop on sols 309- 324. The rugged nature of the outcrop and short time available for analysis limited opportunities for contact science, but ChemCam’s ability to remotely collect compositional and textural observations resulted in a large data set from Shaler. ChemCam conducted analyses of 29 non-soil targets at Shaler, 26 of which used laser-induced breakdown spectroscopy (LIBS) for a total of 9,180 spectra. Three observations used only the remote micro-imager (RMI). Each of the 26 LIBS targets were analyzed at between 5 and 25 points, providing a measure of the target homogeneity and in some cases transecting fine strata.

Conference Paper↗
USGS2013

Pre-flight calibration and initial data processing for the ChemCam laser-induced breakdown spectroscopy instrument on the Mars Science Laboratory rover

The ChemCam instrument package on the Mars Science Laboratory rover, Curiosity, is the first planetary science instrument to employ laser-induced breakdown spectroscopy (LIBS) to determine the compositions of geological samples on another planet. Pre-processing of the spectra involves subtracting the ambient light background, removing noise, removing the electron continuum, calibrating for the wavelength, correcting for the variable distance to the target, and applying a wavelength-dependent correction for the instrument response. Further processing of the data uses multivariate and univariate comparisons with a LIBS spectral library developed prior to launch as well as comparisons with several on-board standards post-landing. The level-2 data products include semi-quantitative abundances derived from partial least squares regression. A LIBS spectral library was developed using 69 rock standards in the form of pressed powder disks, glasses, and ceramics to minimize heterogeneity on the scale of the observation (350–550 μm dia.). The standards covered typical compositional ranges of igneous materials and also included sulfates, carbonates, and phyllosilicates. The provenance and elemental and mineralogical compositions of these standards are described. Spectral characteristics of this data set are presented, including the size distribution and integrated irradiances of the plasmas, and a proxy for plasma temperature as a function of distance from the instrument. Two laboratory-based clones of ChemCam reside in Los Alamos and Toulouse for the purpose of adding new spectra to the database as the need arises. Sensitivity to differences in wavelength correlation to spectral channels and spectral resolution has been investigated, indicating that spectral registration needs to be within half a pixel and resolution needs to match within 1.5 to 2.6 pixels. Absolute errors are tabulated for derived compositions of each major element in each standard using PLS regression. Sources of errors are investigated and discussed, and methods for improving the analytical accuracy of compositions derived from ChemCam spectra are discussed.

Spectrochimica Acta Part B: Atomic Spectroscopy↗
USGS2013

Martian fluvial conglomerates at Gale Crater

Observations by the Mars Science Laboratory Mast Camera (Mastcam) in Gale crater reveal isolated outcrops of cemented pebbles (2 to 40 millimeters in diameter) and sand grains with textures typical of fluvial sedimentary conglomerates. Rounded pebbles in the conglomerates indicate substantial fluvial abrasion. ChemCam emission spectra at one outcrop show a predominantly feldspathic composition, consistent with minimal aqueous alteration of sediments. Sediment was mobilized in ancient water flows that likely exceeded the threshold conditions (depth 0.03 to 0.9 meter, average velocity 0.20 to 0.75 meter per second) required to transport the pebbles. Climate conditions at the time sediment was transported must have differed substantially from the cold, hyper-arid modern environment to permit aqueous flows across several kilometers.

Science↗