Geology Reports⌕ Search

Geology topics

Robert B. Finkelman

Publications and source records attributed to Robert B. Finkelman.

26 records · Page 2Linked to original sources
USGS1994

Modes of occurrence of potentially hazardous elements in coal: Levels of confidence

The modes of occurrence of the potentially hazardous elements in coal will be of significance in any attempt to reduce their mobilization due to coal combustion. Antimony and selenium may be present in solid solution in pyrite, as minute accessory sulfides dispersed throughout the organic matrix, or in organic association. Because of these modes of occurrence it is anticipated that less than 50% of these elements will be routinely removed by conventional coal cleaning procedures. Arsenic and mercury occur primarily in late-stage coarse-grained pyrite therefore physical coal cleaning procedures should be successful in removing substantial proportions of these elements. Cadmium occurs in sphalerite and lead in galena. Both of these minerals exhibit a wide range of particle sizes and textural relations. Depending on the particle size and textural relations, physical coal cleaning may remove as little as 25% of these elements or as much as 75%. Manganese in bituminous coal occurs in carbonates, especially siderite. Physical coal cleaning should remove a substantial proportion of this element. More information is needed to elucidate the modes of occurrence of beryllium, chromium, cobalt, and nickel.

Fuel Processing Technology↗
USGS1984

Interlaboratory comparison of mineral constituents in a sample from the Herrin (No. 6) coal bed from Illinois

Approximately 20 kg of the Herrin (No. 6) coal was collected from a strip mine in St. Clair County, Ill. A 10-kg portion was ground to -60 mesh, homogenized, and riffled into 128 splits of 70-80 g each. Homogeneity of these splits was confirmed by moisture, ash, and sulfur analyses of six randomly selected splits. Results of these analyses were within the ASTM (American Society for Testing and Materials) guidelines for interlaboratory precision. Splits of the Herrin (No. 6) coal were then transmitted to more than 30 laboratories for analysis. Low-temperature plasma oxidation was used to isolate inorganic matter for quantitative chemical and mineralogical analysis. Despite a wide variation in ashing conditions, only minor variations in ash yields were obtained; these variations were attributed to differences in operating temperature and moisture content. Mineralogical analyses of low-temperature ash (LTA) concentrates prepared by five different laboratories indicated variations within the limits of analytical error. The mean values, in weight percent, for the major minerals are as follows: calcite, 9; quartz, 20; pyrite, 23; kaolinite, 14; and illite+mixed-layer clays, 31. Normative mineralogical calculations and Fourier transform infrared analysis (FTIR) yielded results similar to those obtained from X-ray diffraction (XRD). Choosing appropriate mineral standards was found to be critical for the proper use of analytical techniques such as XRD and FTIR. Good interlaboratory agreement was obtained for most major, minor, and trace elements despite differences in analytical procedures and in the type of sample analyzed (coal, high-temperature ash, or LTA). Discrepancies between analyses for zinc, strontium, manganese, and iron may be attributed to sampling inhomogeneity problems. Mossbauer spectroscopy showed that approximately 44 percent of the pyritic sulfur was lost through weathering in the first year after preparation of the interlaboratory sample. Szomolnokite and possibly coquimbite and jarosite were also identified. Scanning electron microscopy studies indicated ubiquitous pyrite framboids and, less commonly, euhedral crystals, skeletal grains, irregularly shaped particles, and vein fillings. Minor accessory minerals such as rare-earth phosphates and possibly silicates, zircon, barium sulfate, titanium oxide, and sphalerite were also found. The textural evidence indicates that the minerals in the banded material are detrital whereas the minerals occurring as vein and pore fillings are authigenic. Magnetic measurements indicate that coal crushed in a steel pulverizer is contaminated by small quantities of abrasion fragments from the crusher, which seriously affect the measured magnetic properties of the coal.

Circular↗
USGS1978

Release of trace elements from a burning bituminous culm bank

A burning bituminous coal waste-bank at Mather, PA was studied in order to determine if trace elements are being released into the environment in substantial concentrations. Samples of the minerals forming on the surface of the bank, the gases escaping from vents, and the water and sediment from a nearby stream were analyzed to determine the presence of these elements. The output of trace elements from the Mather bank, as is evidenced by the minerals forming on the surface, is relatively low compared to the output from actively burning anthracite culm-banks. Copper was the only element of potential environmental significance found accumulating on the Mather bank. However, the sediment in the vicinity of the bank and the waters immediately downstream did not have anomolously high concentrations of copper. Relatively high concentrations of arsenic were found in the organic matter at the base of the bank but no evidence of high As values were found downstream. No potentially toxic elements, other than sulfur, were detected in the gases being emitted from the culm-bank. Because of the quiescent condition of the Mather culm-bank the question of the fate of trace elements released in the burning process remains unanswered.

Open-File Report↗
USGS1975

Perched silica minerals on mordenite fiber

Ellipsoidal quartz grains and spherulitic chalcedony are perched on mordenite fibers in geodes from Chihuahua, Mexico. Examination of samples of fibrous mordenite from six additional localities indicated that most mordenites have perched quartz crystals. A linear relationship exists between the Si:Al ratios and the refractive indices of the mordenites. The pH of the mineralizing solutions appears to be the primary factor controlling the presence of perched silica minerals (the lower the pH, the higher the Si:Al ratios and the lower the probability of precipitating quartz). Other factors that may affect the presence of lurched silica minerals are (1) the compactness of the mordenite fibers, (2) the morphology of the fibers, and (3) the concentration of Al, Ca, Na, and K in the mineralizing solutions.

Journal of Research of the U.S. Geological Survey↗