Geology topics

Richard Styron

Publications and source records attributed to Richard Styron.

3 recordsLinked to original sources

USGS2020

Improving paleoseismic earthquake magnitude estimates with rupture length information: Application to the Puget Lowland, Washington State, U.S.A.

Both earthquake displacement and rupture length correlate with magnitude, and therefore observations of each from past earthquakes can be used to estimate the magnitude of those earthquakes in the absence of instrumental records. We extend the Bayesian inversion method of Biasi and Weldon (2006), which estimates paleoearthquake magnitude from displacement observations, to incorporate both rupture length and surface displacement measurements into the magnitude inversion. We then use this method on 27 late Pleistocene to Holocene paleoearthquakes in the Puget Lowland region of Washington. Observations of (typically vertical) fault separation per event range from 0.6 to 7 m, implying net displacement per event of up to 10 ± 4 m for the largest event. Rupture lengths are estimated to vary between the smallest contiguous mapped scarps to the full extent of the faults mapped from geology and geophysical observations. Although a few of the ruptures may be longer than 150 km, the ruptures have a median of 53 km, indicating that earthquakes in the Puget Lowland have relatively high displacement to length ratios. By considering both datasets, we find that all events were between M 6.3 and 7.5, generally consistent with the expected seismicity from the USGS National Seismic Hazard Map for the region. The simultaneous use of both length and displacement data in the magnitude inversion decreases both the estimated earthquake magnitudes and the uncertainty. The magnitude reduction in particular is due to the relatively short rupture lengths possible for Puget Lowland faults. This implies a decrease in the seismic hazard (relative to a displacement-only assessment) to a highly populated and rapidly urbanizing region.

Washington↗

USGS2018

Crustal structure and quaternary acceleration of deformation rates in central Washington revealed by stream profile inversion, potential field geophysics, and structural geology of the Yakima folds

Post‐Miocene tectonic uplift along fault‐cored anticlines within central Washington produced the Yakima Fold Province, a region of active NNE‐SSW shortening in the Cascadian backarc. The relative timing and rate of deformation along individual structures is coarsely defined yet imperative for seismic hazard assessment. In this work, we use geomorphic and geophysical mapping, stream profile inversion, and balanced cross‐section methods to constrain fault geometries and slip rates in the Yakima Canyon region. We extract stream profiles from LiDAR data and analytically solve for the rate of relative rock uplift along several active fault‐cored anticlines. To constrain the fault geometries at depth and the long‐term magnitude of deformation, we constructed two line‐balanced cross sections across the folds with forward‐modeled magnetic and gravity anomaly data. Our stream profile results indicate an increase of incision rates in the Pleistocene, and we infer the increase is tectonically controlled. We estimate modern slip rates between 0.4 and 0.6 mm/year accommodated on reverse faults that core the Manastash Ridge, Umtanum Ridge, and Selah Butte anticlines and establish that these faults reactivate and invert older normal faults in basement rocks. Finally, we calculate the time required to accumulate sufficient strain energy for a large magnitude earthquake (M ≥ 7) along individual structures in the Yakima Fold Province. Results show that the Yakima folds likely accommodate large magnitude earthquakes and that it takes several hundred to several thousand years to accumulate sufficient strain energy for an M ≥ 7 earthquake.

Washington↗

USGS2017

Miocene−Pleistocene deformation of the Saddle Mountains: Implications for seismic hazard in central Washington, USA

The Yakima fold province, located in the backarc of the Cascadia subduction zone, is a region of active strain accumulation and deformation distributed across a series of fault-cored folds. The geodetic network in central Washington has been used to interpret large-scale N-S shortening and westward-increasing strain; however, geodetic data are unable to resolve shortening rates across individual structures in this low-strain-rate environment. Resolving fault geometries, slip rates, and timing of faulting in the Yakima fold province is critically important to seismic hazard assessment for nearby infrastructure and population centers. The Saddle Mountains anticline is one of the most prominent Yakima folds. It is unique within the Yakima fold province in that the syntectonic strata of the Ringold Formation are preserved and provide a record of deformation and drainage reorganization. Here, we present new stratigraphic columns, U-Pb zircon tephra ages, U-series caliche ages, and geophysical modeling that constrain two line-balanced and retrodeformed cross sections. These new constraints indicate that the Saddle Mountains anticline has accommodated 1.0−1.3 km of N-S shortening since 10 Ma, that shortening increases westward along the anticline, and that the average slip rate has increased 6-fold since 6.8 Ma. Provenance analysis suggests that the source terrane for the Ringold Formation was similar to that of the modern Snake River Plain. Using new slip rates and structural constraints, we calculate the strain accumulation time, interpretable as a recurrence interval, for earthquakes on the Saddle Mountains fault and find that large-magnitude earthquakes could rupture along the Saddle Mountains fault every 2−11 k.y.

Washington↗