Geology Reports⌕ Search

Geology topics

R. H. Morin

Publications and source records attributed to R. H. Morin.

18 recordsLinked to original sources
USGS2012

Information on stress conditions in the oceanic crust from oval fractures in a deep borehole

Oval images etched into the vail of a deep borehole were detected in DSDP (Deep Sea Drilling Project) Hole 504B, eastern equatorial Pacific Ocean, from analysis of an acoustic televiever log. Initial speculation as to the origin of these remarkable features considered the intersection of pillow basalts with the wellbore. However, a systematic inspection of these ovals has identified intriguing consistencies in appearance that cannot be explained satisfactorily by a random, coincidental distribution of pillow lavas. As an alternative hypothesis, Mohr-Coulomb failure criterion is used to account for the generation and orientation of similarly curved, stress-induced fractures. Consequently, these oval features can be interpreted as fractures and related directly to stress conditions in the oceanic crust at this site. The azimuth of the oval center corresponds to the orientation of maximum horizontal principal stress (S H ), and the oval width, which spans approximately 180° of the borehole, is aligned vith the azimuth of minimum horizontal principal stress (S h ). The oval height is controlled by the fracture angle and thus is a function of the coefficient of internal friction of the rock.

Geophysical Research Letters↗
USGS2012

Analysis of geophysical well logs obtained in the State 2-14 borehole, Salton Sea geothermal area, California

A complete suite of conventional geophysical well logs was obtained in the upper part of a 3220-m- deep borehole drilled into geothermally altered alluvial sediments on the southeastern edge of the Salton Sea. In situ temperatures greater than 300°C and an inability to cool parts of the borehole by circulation limited the suite of logs run below 2000 m in depth to deep induction, spontaneous potential, un-calibrated neutron, natural gamma, and temperature. Bottom-hole temperature trends given by repeat temperature logs were extrapolated to undisturbed temperatures approaching 355°C at a depth of 3220 m. Geophysical logs obtained in the State 2–14 borehole indicate that neutron porosity, gamma-gamma, and deep-induction logs provide useful information on lithologic trends with depth. The natural gamma log contains almost continuous, high-frequency fluctuations that obscure lithologic trends and that may be related to recent radioisotope redistribution and departure from radiometric equilibrium. Acoustic transit time logs give unrealistically low in situ compressional velocities ranging from 1.8 to 3.0 km/s, whereas acoustic waveform logs indicate that sediment compressional velocities range from less than 3.0 km/s shallower than 1000 m in depth to almost 5.0 km/s at depths greater than 2000 m. Analyses indicate that most log values lie between two lithologic end points: an electrically conductive claystone with moderate neutron porosity, but no effective porosity, and an electrically nonconductive, fully cemented siltstone that has small but finite porosity. A limited number of clean sandstones depart from this trend; geophysical logs from these sandstones indicate an effective porosity ranging from 5 to 14%, and saturation with brines having equivalent NaCl concentrations greater than 100,000 mg/L. Depth- averaged trends in neutron porosity and deep-induction logs, along with trends in acoustic velocity determined from acoustic waveform logs, demonstrate that major changes in the properties of alluvial sediments occur within the depth range from 1200 to 1800 m. Although caliper logs were not obtained deeper than 2000 m, resistivity values less than 10 ohm m at those depths probably correspond to borehole enlargements in production zones rather than local increases in effective porosity. The transition in sediment properties indicated by the geophysical logs in the depth interval from 1200 to 2000 m apparently represents a detailed vertical profile of the transition from relatively unaltered clay minerals in alluvial sediments to electrically nonconductive alteration products such as epidote and feldspar.

Journal of Geophysical Research Solid Earth↗
USGS2010

Permeability profiles in granular aquifers using flowmeters in direct-push wells

Numerical hydrogeological models should ideally be based on the spatial distribution of hydraulic conductivity ( K ), a property rarely defined on the basis of sufficient data due to the lack of efficient characterization methods. Electromagnetic borehole flowmeter measurements during pumping in uncased wells can effectively provide a continuous vertical distribution of K in consolidated rocks. However, relatively few studies have used the flowmeter in screened wells penetrating unconsolidated aquifers, and tests conducted in gravel-packed wells have shown that flowmeter data may yield misleading results. This paper describes the practical application of flowmeter profiles in direct-push wells to measure K and delineate hydrofacies in heterogeneous unconsolidated aquifers having low-to-moderate K (10 −6 to 10 −4 m/s). The effect of direct-push well installation on K measurements in unconsolidated deposits is first assessed based on the previous work indicating that such installations minimize disturbance to the aquifer fabric. The installation and development of long-screen wells are then used in a case study validating K profiles from flowmeter tests at high-resolution intervals (15 cm) with K profiles derived from multilevel slug tests between packers at identical intervals. For 119 intervals tested in five different wells, the difference in log K values obtained from the two methods is consistently below 10%. Finally, a graphical approach to the interpretation of flowmeter profiles is proposed to delineate intervals corresponding to distinct hydrofacies, thus providing a method whereby both the scale and magnitude of K contrasts in heterogeneous unconsolidated aquifers may be represented.

Ground Water↗
USGS2005

Use of an electromagnetic seepage meter to investigate temporal variability in lake seepage

A commercially available electromagnetic flowmeter is attached to a seepage cylinder to create an electromagnetic seepage meter (ESM) for automating measurement of fluxes across the sediment/water interface between ground water and surface water. The ESM is evaluated through its application at two lakes in New England, one where water seeps into the lake and one where water seeps out of the lake. The electromagnetic flowmeter replaces the seepage-meter bag and provides a continuous series of measurements from which temporal seepage processes can be investigated. It provides flow measurements over a range of three orders of magnitude, and contains no protruding components or moving parts. The ESM was used to evaluate duration of seepage disturbance following meter installation and indicated natural seepage rates resumed approximately one hour following meter insertion in a sandy lakebed. Lakebed seepage also varied considerably in response to lakebed disturbances, near-shore waves, and rain-falls, indicating hydrologic processes are occurring in shallow lakebed settings at time scales that have largely gone unobserved.

Ground Water↗
USGS2005

Contact zone permeability at intrusion boundaries: New results from hydraulic testing and geophysical logging in the Newark Rift Basin, New York, USA

Hydraulic tests and geophysical logging performed in the Palisades sill and the underlying sedimentary rocks in the NE part of the Newark Rift Basin, New York, USA, confirm that the particular transmissive zones are localized within the dolerite-sedimentary rock contact zone and within a narrow interval below this contact zone that is characterized by the occurrence of small layers of chilled dolerite. Transmissivity values determined from fluid injection, aquifer testing, and flowmeter measurements generally fall in the range of 8.1E-08 to 9.95E-06 m 2 /s and correspond to various scales of investigation. The analysis of acoustic and optical BHTV images reveals two primary fracture sets within the dolerite and the sedimentary rocks—subhorizontal fractures, intersected by subvertical ones. Despite being highly fractured either with subhorizontal, subvertical or both fracture populations, the dolerite above and the sedimentary rocks below the contact zone and the zone with the layers of chilled dolerite are significantly less conductive. The distribution of the particular conductive intervals is not a function of the two dominant fracture populations or their density but rather of the intrusion path of the sill. The intrusion caused thermal fracturing and cracking of both formations, resulting in higher permeability along the contact zone.

Hydrogeology Journal↗
USGS2005

Fractured-aquifer hydrogeology from geophysical logs; the passaic formation, New Jersey

The Passaic Formation consists of gradational sequences of mudstone, siltstone, and sandstone, and is a principal aquifer in central New Jersey. Ground‐water flow is primarily controlled by fractures interspersed throughout these sedimentary rocks and characterizing these fractures in terms of type, orientation, spatial distribution, frequency, and transmissivity is fundamental towards understanding local fluid‐transport processes. To obtain this information, a comprehensive suite of geophysical logs was collected in 10 wells roughly 46 m in depth and located within a .05 km 2 area in Hopewell Township, New Jersey. A seemingly complex, heterogeneous network of fractures identified with an acoustic televiewer was statistically reduced to two principal subsets corresponding to two distinct fracture types: (1) bedding‐plane partings and (2) high‐angle fractures. Bedding‐plane partings are the most numerous and have an average strike of N84°W and dip of 20° N. The high‐angle fractures are oriented subparallel to these features, with an average strike of N79° E and dip of 71° S, making the two fracture types roughly orthogonal. Their intersections form linear features that also retain this approximately east‐west strike. Inspection of fluid temperature and conductance logs in conjunction with flow meter measurements obtained during pumping allows the transmissive fractures to be distinguished from the general fracture population. These results show that, within the resolution capabilities of the logging tools, approximately 51 (or 18 percent) of the 280 total fractures are water producing. The bedding‐plane partings exhibit transmissivities that average roughly 5 m 2 /day and that generally diminish in magnitude and frequency with depth. The high‐angle fractures have average transmissivities that are about half those of the bedding‐plane partings and show no apparent dependence upon depth. The geophysical logging results allow us to infer a distinct hydrogeologic structure within this aquifer that is defined by fracture type and orientation. Fluid flow near the surface is controlled primarily by the highly transmissive, subhorizontal bedding‐plane partings. As depth increases, the high‐angle fractures apparently become more dominant hydrologically.

Ground Water↗
USGS2005

Hydrologic properties of coal beds in the Powder River Basin, Montana I. Geophysical log analysis

As part of a multidisciplinary investigation designed to assess the implications of coal-bed methane development on water resources for the Powder River Basin of southeastern Montana, six wells were drilled through Paleocene-age coal bedsalong a 31-km east–west transect within the Tongue River drainage basin. Analysis of geophysical logs obtained in these wells provides insight into the hydrostratigraphic characteristics of the coal and interbedded siliciclastic rocks and their possible interaction with the local stress field. Natural gamma and electrical resistivity logs were effective in distinguishing individual coal beds. Full-waveform sonic logs were used to determine elastic properties of the coal and an attendant estimate of aquifer storage is in reasonable agreement with that computed from a pumping test. Inspection of magnetically oriented images of the borehole walls generated from both acoustic and optical televiewers and comparison with coal cores infer a face cleat orientation of approximately N33°E, in close agreement with regional lineament patterns and the northeast trend of the nearby Tongue River. The local tectonic stress field in this physiographic province as inferred from a nearby 1984 earthquake denotes an oblique strike-slip faulting regime with dominant east–west compression and north–south extension. These stress directions are coincident with those of the primary fracture sets identified from the televiewer logs and also with the principle axes of the drawdown ellipse produced from a complementary aquifer test, but oblique to apparent cleat orientation. Consequently, examination of these geophysical logs within the context of local hydrologic characteristics indicates that transverse transmissivity anisotropy in these coals is predominantly controlled by bedding configuration and perhaps a mechanical response to the contemporary stress field rather than solely by cleat structure.

Montana↗
USGS2003

Effects of crustal stresses on fluid transport in fractured rock: Case studies from northeastern and southwestern USA

The link between stress and hydrologic properties was examined at two sites that are distinguished by different rock types and different stress states. This investigation is based upon the analysis and interpretation of geophysical logs obtained in water wells at the two locations. At the northeast site (Newark Basin), the hydrologic characteristics of sedimentary rocks are dependent upon the relationship to the current regional stress field of two primary types of orthogonal features that serve as preferential pathways for fluid flow. Subhorizontal bedding-plane partings are highly transmissive near the surface and delineate transversely isotropic fluid flow at shallow depths. With increasing depth, the subhorizontal planes become less dominant and steeply dipping fractures become more influential hydrologically. These high-angle features define anisotropic flow pathways that are preferentially oriented along strike. At the southwest site (west Texas), extrusive rocks are subjected to topographically modified tectonic and gravitational stresses that vary spatially within a valley setting. The attendant changes in stress invariants cause fracture connectivity within the rock mass to systematically increase with depth along the valley flanks, but to remain relatively low in the central valley. The degree of fracture connectivity predicted within this valley configuration is consistent with variations in transmissivity determined at several well locations. In each of these cases, the idealized understanding of the hydrologic system is enhanced by considering the effects of regional and local stresses that act upon the fractured-rock aquifer.

Hydrogeology Journal↗
USGS2002

Topographic stress perturbations in southern Davis Mountains, west Texas 1. Polarity reversal of principal stresses

We have applied a previously developed analytical stress model to interpret subsurface stress conditions inferred from acoustic televiewer logs obtained in two municipal water wells located in a valley in the southern Davis Mountains near Alpine, Texas. The appearance of stress-induced breakouts with orientations that shift by 90° at two different depths in one of the wells is explained by results from exact solutions for the effects of valleys on gravity and tectonically induced subsurface stresses. The theoretical results demonstrate that above a reference depth termed the hinge point, a location that is dependent on Poisson's ratio, valley shape, and magnitude of the maximum horizontal tectonic stress normal to the long axis of the valley, horizontal stresses parallel to the valley axis are greater than those normal to it. At depths below this hinge point the situation reverses and horizontal stresses normal to the valley axis are greater than those parallel to it. Application of the theoretical model at Alpine is accommodated by the fact that nearby earthquake focal mechanisms establish an extensional stress regime with the regional maximum horizontal principal stress aligned perpendicular to the valley axis. We conclude that the localized stress field associated with a valley setting can be highly variable and that breakouts need to be examined in this context when estimating the orientations and magnitudes of regional principal stresses.

Texas↗
USGS2002

Topographic stress perturbations in southern Davis Mountains, west Texas 2. Hydrogeologic implications

As part of a regional groundwater investigation, geophysical logs were obtained in two municipal water wells located near the west Texas city of Alpine. These boreholes are 252 and 285 m deep and penetrate extrusive rocks of Tertiary age. The deeper well was drilled in the central valley and the other along the northern flank of an east-west trending valley-ridge setting. Analysis and interpretation of the logs reveal that the two wells are subjected to significantly different stress environments because of topographic effects and exhibit significantly different hydrogeologic properties. Water production is associated with two specific types of features common to both wells: (1) the upper and lower contacts of a dense trachyte unit located in the shallow part of the wells and (2) deeper zones of highly fractured rocks within the interior of a basalt formation. The transmissivity of the trachyte boundaries is twice as large in the central valley well as it is in the ridge flank well, whereas the transmissivity of the deeper basalts is an order of magnitude greater in the flank well than it is in the central well. This discrepancy is examined from the perspective of rock failure, fracture opening, and flow enhancement by computing values for a Drucker-Prager stability factor that is based on the magnitudes of the normal and deviatoric stress invariants as a function of depth. Thus the field measurements and subsequent stress analysis offer evidence of a coupled tectonic-hydrologic interaction at this site.

Texas↗
USGS2002

Determining the hydraulic properties of saturated, low-permeability geological materials in the laboratory: Advances in theory and practice

The accurate hydraulic characterization of low-permeability subsurface environments has important practical significance. In order to examine this issue from the perspective of laboratory-based approaches, we review some recent advancements in the theoretical analyses of three different laboratory techniques specifically applied to low-permeability geologic materials: constant-head, constant flow-rate and transient-pulse permeability tests. Some potential strategies for effectively decreasing the time required to confidently estimate the permeability of these materials are presented. In addition, a new and versatile laboratory system is introduced that can implement any of these three test methods while simultaneously subjecting a specimen to high confining pressures and pore pressures, thereby simulating in situ conditions at great depths. The capabilities and advantages of this innovative system are demonstrated using experimental data derived from Shirahama sandstone and Inada granite, two rock types widely encountered in Japan.

Conference Paper↗
USGS2000

Instruments and methods acoustic televiewer logging in glacier boreholes

The acoustic televiewer is a geophysical logging instrument that is deployed in a water-filled borehole and operated while trolling. It generates a digital, magnetically oriented image of the borehole wall that is developed from the amplitudes and transit times of acoustic waves emitted from the tool and reflected at the water-wall interface. The transit-time data are also converted to radial distances, from which cross-sectional views of the borehole shape can be constructed. Because the televiewer is equipped with both a three-component magnetometer and a two-component inclinometer, the borehole's trajectory in space is continuously recorded as well. This instrument is routinely used in mining and hydrogeologic applications, but in this investigation it was deployed in two boreholes drilled into Upper Fremont Glacier, Wyoming, U.S.A. The acoustic images recorded in this glacial setting are not as clear as those typically obtained in rocks, due to a lower reflection coefficient for water and ice than for water and rock. Results indicate that the depth and orientation of features intersecting the boreholes can be determined, but that interpreting their physical nature is problematic and requires corroborating information from inspection of cores. Nevertheless, these data can provide some insight into englacial structural characteristics. Additional information derived from the cross-sectional geometry of the borehole, as well as from its trajectory, may also be useful in studies concerned with stress patterns and deformation processes.

Journal of Glaciology↗
USGS1999

Analysis of stress-induced oval fractures in a borehole at Deep Sea Drilling Project Site 504, eastern equatorial Pacific

Deep Sea Drilling Project (DSDP) Hole 504B is located in the eastern equatorial Pacific Ocean and extends to a total depth of 2111 m beneath the seafloor (mbsf). Several acoustic televiewer logs have been obtained in this well during successive stages of drilling, and the resulting digital images have revealed numerous oval-shaped fractures seemingly etched into the borehole wall. A theoretical examination of these stress-induced features identifies a unique and ephemeral set of stress distributions and magnitudes that are necessary for their production. Consequently, the ovals provide a basis for quantifying the magnitudes and orientations of the maximum and minimum horizontal principal stresses, S H and S h at this site. Vertical, truncated breakouts and horizontal tensile fractures define the spatial boundaries of the ovals. Explicit criteria for their occurrence are combined with estimates for various physical properties of the rock to yield a range of possible values for the horizontal principal stresses. The conspicuous oval geometry is completed by a curved fracture that joins the vertical and horizontal components. Its degree of curvature is delineated by the modified Griffith failure criterion and is directly related to the principal stress difference ( S H − S h ). Matching a series of type curves corresponding to specific values for ( S H − S h ) with the actual undistorted well bore images allows the magnitude of the stress difference to be further constrained. With a value for ( S H − S h ) of 45 ± 5 MPa the individual magnitudes of S H and S h are determined more precisely. Final estimates for the horizontal principal stresses in DSDP Hole 504B at a depth of 1200 mbsf are 141 MPa ≤ S H ≤ 149 MPa and 91 MPa ≤ S h ≤ 109 MPa. Stress magnitudes derived from this approach rely heavily upon the values of a variety of physical properties, and complementary laboratory measurements performed on relevant rock samples provide critical information. Uncertainties in estimating these properties translate into less precise predictions of principal stresses.

Journal of Geophysical Research B: Solid Earth↗
USGS1999

Hydrogeologic structure of the Newark Basin, Pennsylvania, from borehole geophysical logs

The Brunswick and the underlying Lockatong Formations are comprised of littrifled Mesozoic sediments that constitute part of the Newark Basin in southeastern Pennsylvania (USA). These fractured rocks form an important regional aquifer that consists of gmdational sequences of shale, siltstone, and sandstone, with fluid transport occurring primarily in fractures. An extensive suite of geophysical logs was obtained in seven wells located at the borough of Iamsdale, PA in order to characterize the areal hydrogeologic system. Analyses of these data indicate that the aquifer can be separated into two distinct structural domains which may, in turn, reflect different mechanical responses to basin bxtension: (1) In the shallow zone above 125 m, the dominant fmcucre population consists of gertfly dipping bedding-plane partings that strike N46°E and dip to the NW at about 11°. Fluid flow is concentrated within the upper 80 m and transmissivities rapidly diminish in magnitude with depth. (2) The zone below 125 m marks the appearance of numerous steeply dipping fractures that are orthogonal to the bedding plane features, striking subparallel at N227°E but dipping sharply to the SE at 77°. This secondary set of fractures is associated with a reasonably thick (= 60 m) high-resistivity, low- transmissivity sandstoned siltstone unit that is abruptly terminated by a thin shale bed at a depth of 190 m. This lower contact effectively delineates the aquifer's vertical extent and the observed lack of hydraulic productivity with increasing depth may be associated with the gradational transition into the Lockatong Formation.

Pennsylvania↗
USGS1998

Theoretical Evaluation of the Transient Response of Constant Head and Constant Flow-Rate Permeability Tests

A theoretical analysis is presented that compares the response characteristics of the constant head and the constant flowrate (flow pump) laboratory techniques for quantifying the hydraulic properties of geologic materials having permeabilities less than 10-10 m/s. Rigorous analytical solutions that describe the transient distributions of hydraulic gradient within a specimen are developed, and equations are derived for each method. Expressions simulating the inflow and outflow rates across the specimen boundaries during a constant-head permeability test are also presented. These solutions illustrate the advantages and disadvantages of each method, including insights into measurement accuracy and the validity of using Darcy's law under certain conditions. The resulting observations offer practical considerations in the selection of an appropriate laboratory test method for the reliable measurement of permeability in low-permeability geologic materials.

Geotechnical Testing Journal↗