Geology Reports⌕ Search

Geology topics

P. E. Hart

Publications and source records attributed to P. E. Hart.

At least 19 recordsLinked to original sources
USGS2013

Methods and spatial extent of geophysical Investigations, Mono Lake, California, 2009 to 2011

This report summarizes the methods and spatial extent of geophysical surveys conducted on Mono Lake and Paoha Island by U.S. Geological Survey during 2009 and 2011. The surveys include acquisition of new high resolution seismic reflection data, shipborne high resolution magnetic data, and ground magnetic and gravity data on Paoha Island. Several trials to acquire swath bathymetry and side scan sonar were conducted, but were largely unsuccessful likely due to physical properties of the water column and (or) physical properites of the highly organic bottom sediment.

California↗
USGS2012

Comparison of Vibroseis and explosive source methods for deep crustal seismic reflection profiling in the Basin and Range province

Direct comparison of low-fold, high-energy explosive and high-fold, lower-energy Vibroseis methods for acquiring deep crustal seismic reflection data in the Basin and Range Province suggests that the high-fold common midpoint (CMP) method there does not provide the best possible image of lower crustal structure. During the recent acquisition of a Vibroseis profile in the Basin and Range Province we fired single deep shot holes to obtain a coincident single-fold explosive section. Within the upper crust (upper 3 s) the explosive source and Vibroseis records are nearly equivalent. For record times below 3 s, however, comparison of the explosive source gathers and the coincident final 60-fold Vibroseis section demonstrates that low-fold explosive profiling provides a higher-quality image of the midcrust to lower crust (3–10 s). The higher record quality of the explosive sources results primarily from the larger seismic energy levels produced by the explosives, making them less sensitive to common noise sources. Whereas deeper than 4–5 s the Vibroseis energy levels on individual source efforts fall to that of ambient noise levels, the explosions provide signal-generated energy exceeding ambient noise levels down to 18–19 s. Although individual reflections can be correlated on explosion and Vibroseis shot gathers, reflection events on the 60-fold Vibroseis stack do not correlate to those on the single-fold explosion profile, suggesting that the high-fold CMP method in our study did not maintain the integrity of the weak lower crustal reflected arrivals. Reasons why the high-fold CMP method apparently failed include complex, even time-varying, statics, nonhyperbolic moveout at long offsets, and the difficulty in resolving stacking velocities with data having low signal-to-noise ratios. Reflections on the explosion section are longer and imply a greater degree of layering than one would infer from the lower-energy Vibroseis section.

Journal of Geophysical Research↗
USGS2009

Coastline shifts and probable ship landing site submerged off ancient Locri-Epizefiri, southern Italy

A geophysical survey provides new information on marine features located seaward of Locri-Epizefiri (Locri), an ancient Greek settlement on the Ionian coastal margin in southern Italy. The study supplements previous work by archaeologists who long searched for the site's harbor and recently identified what was once a marine basin that is now on land next to the city walls of Locri. Profiles obtained offshore, between the present coast and outer shelf, made with a high-resolution, seismic subbottom-profiling system, record spatial and temporal variations of buried Holocene deposits. Two of these submerged features are part of a probable now-submerged ship landing facility. The offshore features can be linked to coastline displacements that occurred off Locri: a sea-to-land shift before Greek settlement, followed by a shoreline reversal from the archaeological site back to sea, and more recently, a return landward. The seaward directed coastal shift that occurred after Locri's occupation by Greeks was likely caused by land uplift near the coastal margin and tectonic seaward shift of the coast, as documented along this geologically active sector of the Calabrian Arc. The seismic survey records an angular, hook-shaped, low rise that extends from the present shore and is now buried on the inner shelf. The rise, enclosing a core lens of poorly stratified to transparent acoustic layers, bounds a broad, low-elevation zone positioned immediately seaward of the shoreline. Close proximity of the raised feature to the low-elevation area suggests it may have been a fabricated structure that functioned as a wave-break for a ship-landing site. The study indicates that the basin extended offshore as a function of the coastline's seaward migration during and/or after Greek occupation of Locri.

Journal of Coastal Research↗
USGS2008

Geologic framework of the 2005 Keathley Canyon gas hydrate research well, northern Gulf of Mexico

The Keathley Canyon sites drilled in 2005 by the Chevron Joint Industry Project are located along the southeastern edge of an intraslope minibasin (Casey basin) in the northern Gulf of Mexico at 1335 m water depth. Around the drill sites, a grid of 2D high-resolution multichannel seismic data designed to image depths down to at least 1000 m sub-bottom reveals 7 unconformities and disconformities that, with the seafloor, bound 7 identifiable seismic stratigraphic units. A major disconformity in the middle of the units stands out for its angular baselapping geometry. From these data, three episodes of sedimentary deposition and deformation are inferred. The oldest episode consists of fine-grained muds deposited during a period of relative stability in the basin (units e, f, and g). Both the BSR and inferred gas hydrate occur within these older units. The gas hydrate occurs in near-vertical fractures. A second episode (units c and d) involved large vertical displacements associated with infilling and ponding of sediment. This second interval corresponds to deposition of intercalated fine and coarse-grained material that was recovered in the drill hole that penetrated the thin edges of the regionally much thicker units. The final episode of deposition (units a and b) occurred during more subdued vertical motions. Hemipelagic drape (unit a) characterizes the modern seafloor. The present-day Casey basin is mostly filled. Its sill is part of a subsiding graben structure that is only 10-20 m shallower than the deepest point in the basin, indicating that gravity-driven transport would mostly bypass the basin. Contemporary faulting along the basin margins has selectively reactivated an older group of faults. The intercalated sand and mud deposits of units c and d are tentatively correlated with Late Pleistocene deposition derived from the western shelf-edge delta/depocenter of the Mississippi River, which was probably most active from 320 ka to 70 ka [Winker, C.D., Booth, J., 2000. Sedimentary dynamics of the salt-dominated continental slope, Gulf of Mexico: integration of observations from the seafloor, near-surface, and deep subsurface. In: Proceedings of the GCSSEPM Foundation 20th Annual Research Conference, Deep-water Reservoirs of the World, pp. 1059-1086]. The presence of sand within the gas hydrate stability zone (in units c and d) is not sufficient to concentrate gas hydrate even though dispersed gas hydrate occurs deeper in the fractured mud/clay-rich sections of units e and f.

Gulf of Mexico↗
USGS2008

Gas and gas hydrate distribution around seafloor seeps in Mississippi Canyon, Northern Gulf of Mexico, using multi-resolution seismic imagery

To determine the impact of seeps and focused flow on the occurrence of shallow gas hydrates, several seafloor mounds in the Atwater Valley lease area of the Gulf of Mexico were surveyed with a wide range of seismic frequencies. Seismic data were acquired with a deep-towed, Helmholz resonator source (220-820 Hz); a high-resolution, Generator-Injector air-gun (30-300 Hz); and an industrial air-gun array (10-130 Hz). Each showed a significantly different response in this weakly reflective, highly faulted area. Seismic modeling and observations of reversed-polarity reflections and small scale diffractions are consistent with a model of methane transport dominated regionally by diffusion but punctuated by intense upward advection responsible for the bathymetric mounds, as well as likely advection along pervasive filamentous fractures away from the mounds.

Marine and Petroleum Geology↗
USGS2008

A photographic and acoustic transect across two deep-water seafloor mounds, Mississippi Canyon, northern Gulf of Mexico

In the northern Gulf of Mexico, a series of seafloor mounds lie along the floor of the Mississippi Canyon in Atwater Valley lease blocks 13 and 14. The mounds, one of which was drilled by the Chevron Joint Industry Project on Methane Hydrates in 2005, are interpreted to be vent-related features that may contain significant accumulations of gas hydrate adjacent to gas and fluid migration pathways. The mounds are located ???150 km south of Louisiana at ???1300 m water depth. New side-scan sonar data, multibeam bathymetry, and near-bottom photography along a 4 km northwest-southeast transect crossing two of the mounds (labeled D and F) reveal the mounds' detailed morphology and surficial characteristics. Mound D, ???250 m in diameter and 7-10 m in height, has exposures of authigenic carbonates and appears to result from a seafloor vent of slow-to-moderate flux. Mound F, which is ???400 m in diameter and 10-15 m high, is covered on its southwest flank by extruded mud flows, a characteristic associated with moderate-to-rapid flux. Chemosynthetic communities visible on the bottom photographs are restricted to bacterial mats on both mounds and mussels at Mound D. No indications of surficial gas hydrates are evident on the bottom photographs.

Marine and Petroleum Geology↗
USGS2003

Structure and mechanics of the Hayward-Rodgers Creek Fault step-over, San Francisco Bay, California

A dilatational step - over between the right-lateral Hayward and Rodgers Creek faults lies beneath San Pablo Bay in the San Francisco Bay area. A key seismic hazard issue is whether an earthquake on one of the faults could rupture through the step - over , enhancing its maximum possible magnitude. If ruptures are terminated at the step - over , then another important issue is how strain transfers through the step . We developed a combined seismic reflection and refraction cross section across south San Pablo Bay and found that the Hayward and Rodgers Creek faults converge to within 4 km of one another near the surface, about 2 km closer than previously thought. Interpretation of potential field data from San Pablo Bay indicated a low likelihood of strike-slip transfer faults connecting the Hayward and Rodgers Creek faults. Numerical simulations suggest that it is possible for a rupture to jump across a 4-km fault gap, although special stressing conditions are probably required (e.g., Harris and Day, 1993, 1999). Slip on the Hayward and Rodgers Creek faults is building an extensional pull-apart basin that could contain hazardous normal faults. We investigated strain in the pull-apart using a finite-element model and calculated a ∼0.02-MPa/yr differential stressing rate in the step - over on a least-principal-stress orientation nearly parallel to the strike-slip faults where they overlap. A 1- to 10-MPa stress-drop extensional earthquake is expected on normal faults oriented perpendicular to the strike-slip faults every 50-500 years. The last such earthquake might have been the 1898 M 6.0-6.5 shock in San Pablo Bay that apparently produced a small tsunami. Historical hydrographic surveys gathered before and after 1898 indicate abnormal subsidence of the bay floor within the step - over , possibly related to the earthquake. We used a hydrodynamic model to show that a dip-slip mechanism in north San Pablo Bay is the most likely 1898 rupture scenario to have caused the tsunami. While we find no strike-slip transfer fault between the Hayward and Rodgers Creek faults, a normal- fault link could enable through-going segmented rupture of both strike-slip faults and may pose an independent hazard of M ∼6 earthquakes like the 1898 event.

California↗
USGS2002

High-resolution seismic-reflection investigation of the northern Gulf of Mexico gas-hydrate-stability zone

We recorded high-resolution seismic-reflection data in the northern Gulf of Mexico to study gas and gas-hydrate distribution and their relation to seafloor slides. Gas hydrate is widely reported near the seafloor, but is described at only one deep drill site. Our data show high-reflectivity zones (HRZs) near faults, diapirs, and gas vents and interbedded within sedimentary sections at shallow depth (<1 km). The HRZs lie below the gas-hydrate-stability zone (GHSZ) as well as within the zone (less common), and they coincide with zones of shallow water-flows. Bottom simulating reflections are rare in the Gulf, and not documented in our data. We infer HRZs result largely from free gas in sandy beds, with gas hydrate within the GHSZ. Our estimates for the base BHSZ correlate reasonably with the top of HRZs in some thick well-layered basin sections, but poorly where shallow sediments are thin and strongly deformed. The equivocal correlation results from large natural variability of parameters that are used to calculate the base of the GHSZ. The HRZs may, however, be potential indicators of nearby gas hydrate. The HRZs also lie at the base of at least two large seafloor slides (e.g. up to 250 km2) that may be actively moving along decollement faults that sole within the GHSZ or close to the estimated base of the GHSZ. We suspect that water/gas flow along these and other faults such as 'chimney' features provide gas to permit crystallization of gas hydrate in the GHSZ. Such flows weaken sediment that slide down salt-oversteepened slopes when triggered by earthquakes. Published by Elsevier Science Ltd.

Marine and Petroleum Geology↗
USGS2000

Bathymetric, geophysical and geologic sample data from Medicine Lake, Siskiyou County, northern California

In September, 1999, the U.S. Geological Survey acquired high-resolution bathymetry, seismic reflection profiles, and geologic sample data from Medicine Lake, a high altitude (2,036 m) lake located within the summit caldera/basin at Medicine Lake volcano (MLV), a dormant Quaternary shield volcano located in the Cascade Range, 50 km northeast of Mt. Shasta. It last erupted less than 1000 years ago.The purpose of this work was to assess whether sediments in the lake might provide a high-resolution record of the climate, volcanic and geochemical (particularly mercury) history of the region. We are still working with our data to assess whether the sediments are appropriate for further study. This report provides a summary of what we have learned to date.

California↗
USGS2000

Reprocessing of multi-channel seismic-reflection data collected in the Beaufort Sea

Contained on this set of two CD-ROMs are stacked and migrated multi-channel seismic-reflection data for 65 lines recorded in the Beaufort Sea by the United States Geological Survey in 1977. All data were reprocessed by the USGS using updated processing methods resulting in improved interpretability. Each of the two CD-ROMs contains the following files: 1) 65 files containing the digital seismic data in standard, SEG-Y format; 2) 1 file containing navigation data for the 65 lines in standard SEG-P1 format; 3) an ASCII text file with cross-reference information for relating the sequential trace numbers on each line to cdp numbers and shotpoint numbers; 4) 2 small scale graphic images (stacked and migrated) of a segment of line 722 in Adobe Acrobat (R) PDF format; 5) a graphic image of the location map, generated from the navigation file; 6) PlotSeis, an MS-DOS Application that allows PC users to interactively view the SEG-Y files; 7) a PlotSeis documentation file; and 8) an explanation of the processing used to create the final seismic sections (this document).

Open-File Report↗
USGS1999

Development of San Leandro synform and neotectonics of the San Francisco Bay block, California

High-resolution, 24-channel seismic-reflection data show a stratified synform beneath south San Francisco Bay. These seismic-reflection data reveal an eastward-dipping bedrock surface that is about 40 m deep (subbottom) beneath the western south bay, and that reaches a maximum observed depth of 500-800 m (subbottom) below the eastern half of the south bay. An angular unconformity cuts both the synform and underlying bedrock. The age of the unconformity is unknown but may be Pleistocene, when these strata forming the synform were presumably exposed subaerially during lowered sea levels. The synformal strata, the unconformity, and some generally flat-lying and overlying strata are folded near the eastern shore of the bay. This folding may result from movement on the Hayward fault (fault interactions and localized strain partitioning) or from compressional deformation in the East Bay Hills related to NE-SW ('fault-normal') convergence between the Pacific and North American plates. In general, reflections from sediment overlying the unconformity are flat lying (except near the eastern shore of the bay), whereas reflections beneath the unconformity dip eastward. The overlying, flat sediment section fills a shallow basin that is coincident with an elliptical residual gravity low. This low appears to be related to the deeper sedimentary, synformal section based on the spatial correlation between the east-dipping reflections and the gravity anomaly. Projecting the east-dipping reflections to the center of the gravity low suggests that the total section of flat-lying and dipping reflections in the synform may exceed 1000 m. Modeling of the gravity low suggests a total low-density section, about 1.5 km thick, at the center of the synform relative to the surrounding bedrock of presumed Franciscan Complex.High-resolution, 24-channel seismic-reflection data show a stratified synform beneath south San Francisco Bay. These seismic-reflection data reveal an eastward-dipping bedrock surface that is about 40 m deep (subbottom) beneath the western south bay, and that reaches a maximum observed depth of 500-800 m (subbottom) below the eastern half of the south bay. An angular unconformity cuts both the synform and underlying bedrock. The age of the unconformity is unknown but may be Pleistocene, when these strata forming the synform were presumably exposed subaerially during lowered sea levels. The synformal strata, the unconformity, and some generally flat-lying and overlying strata are folded near the eastern shore of the bay. This folding may result from movement on the Hayward fault (fault interactions and localized strain partitioning) or from compressional deformation in the East Bay Hills related to NE-SW (`fault-normal') convergence between the Pacific and North American plates. In general, reflections from sediment overlying the unconformity are flat lying (except near the eastern shore of the bay), whereas reflections beneath the unconformity dip eastward. The overlying, flat sediment section fills a shallow basin that is coincident with an elliptical residual gravity low. This low appears to be related to the deeper sedimentary, synformal section based on the spatial correlation between the east-dipping reflections and the gravity anomaly. Projecting the east-dipping reflections to the center of the gravity low suggests that the total section of flat-lying and dipping reflections in the synform may exceed 1000 m. Modeling of the gravity low suggests a total low-density section, about 1.5 km thick, at the center of the synform relative to the surrounding bedrock of presumed Franciscan Complex.

Marine and Petroleum Geology↗
USGS1999

Dipping San Andreas and Hayward faults revealed beneath San Francisco Bay, California

The San Francisco Bay area is crossed by several right-lateral strike-slip faults of the San Andreas fault zone. Fault-plane reflections reveal that two of these faults, the San Andreas and Hayward, dip toward each other below seismogenic depths at 60° and 70°, respectively, and persist to the base of the crust. Previously, a horizontal detachment linking the two faults in the lower crust beneath San Francisco Bay was proposed. The only near-vertical-incidence reflection data available prior to the most recent experiment in 1997 were recorded parallel to the major fault structures. When the new reflection data recorded orthogonal to the faults are compared with the older data, the highest amplitude reflections show clear variations in moveout with recording azimuth. In addition, reflection times consistently increase with distance from the faults. If the reflectors were horizontal, reflection moveout would be independent of azimuth, and reflection times would be independent of distance from the faults. The best-fit solution from three-dimensional traveltime modeling is a pair of high-angle dipping surfaces. The close correspondence of these dipping structures with the San Andreas and Hayward faults leads us to conclude that they are the faults beneath seismogenic depths. If the faults retain their observed dips, they would converge into a single zone in the upper mantle ∼45 km beneath the surface, although we can only observe them in the crust.

Geology↗
USGS1997

Amplitude versus offset modeling of the bottom simulating reflection associated with submarine gas hydrates

A bottom simulating seismic reflection (BSR) that parallels the sea floor occurs worldwide on seismic profiles from outer continental margins. The BSR coincides with the base of the gas hydrate stability field and is commonly used as indicator of natural submarine gas hydrates. Despite the widespread assumption that the BSR marks the base of gas hydrate-bearing sediments, the occurrence and importance of low-velocity free gas in the sediments beneath the BSR has long been a subject of debate. This paper investigates the relative abundance of hydrate and free gas associated with the BSR by modeling the reflection coefficient or amplitude variation with offset (AVO) of the BSR at two separate sites, offshore Oregon and the Beaufort Sea. The models are based on multichannel seismic profiles, seismic velocity data from both sites and downhole log data from Oregon ODP Site 892. AVO studies of the BSR can determine whether free gas exists beneath the BSR if the saturation of gas hydrate above the BSR is less than approximately 30% of the pore volume. Gas hydrate saturation above the BSR can be roughly estimated from AVO studies, but the saturation of free gas beneath the BSR cannot be constrained from the seismic data alone. The AVO analyses at the two study locations indicate that the high amplitude BSR results primarily from free gas beneath the BSR. Hydrate concentrations above the BSR are calculated to be less than 10% of the pore volume for both locations studied.

Conference Paper↗
USGS1996

Misinterpretation of lateral acoustic variations on high-resolution seismic reflection profiles as fault offsets of Holocene bay mud beneath the southern part of San Francisco Bay, California

We collected high-resolution seismic reflection profiles in the southern part of San Francisco Bay in 1992 and 1993 to investigate possible Holocene faulting along postulated transbay bedrock fault zones. The initial analog records show apparent offsets of reflection packages along sharp vertical boundaries. These records were originally interpreted as showing a complex series of faults along closely spaced, sharp vertical boundaries in the upper 10 m (0.013 s two-way travel time) of Holocene bay mud. A subsequent survey in 1994 was run with a different seismic reflection system, which utilized a higher power source. This second system generated records with deeper penetration (max. 20 m, 0.026 s two-way travel time) and demonstrated that the reflections originally interpreted as fault offsets by faulting were actually laterally continuous reflection horizons. The pitfall in the original interpretations was caused by lateral variations in the amplitude brightness of reflection events, coupled with a long (greater than 15 ms) source signature of the low-power system. These effects combined to show apparent offsets of reflection packages along sharp vertical boundaries. These boundaries, as shown by the second system, in fact occur where the reflection amplitude diminishes abruptly on laterally continuous reflection events. This striking lateral variation in reflection amplitude is attributable to the localized presence of biogenic(?) gas.

Marine and Petroleum Geology↗
USGS1994

Preliminary results of a binational research cruise in the Western Arctic Ocean

This paper is a condensed version of a report on the preliminary results of a research cruise under the direction of the U. S. Geological Survey, on board the United States Coast Guard Cutter Polar Star to Northwind Ridge and Canada Basin of the Western Arctic Ocean, during the period August 16‐September 15, 1993. Major objectives of the cruise were to: survey the geology of the North‐wind Ridge and Canada Basin; determine whether radionuclide contamination from disposal of solid and liquid nuclear wastes by the former Soviet Union in the Kara and Barents seas had penetrated the North American Arctic; acquire sediment cores in support of research on the history of glaciation in the region; and gain a better understanding of water structure and currents, sea‐ice physics, and sediment and nutrient transport.

Arctic Ocean, Canada Basin, Northwind Ridge↗
USGS1994

Seismic evidence for a lower-crustal detachment beneath San Francisco Bay, California

Results from the San Francisco Bay area seismic imaging experiment (BASIX) reveal the presence of a prominent lower crustal reflector at a depth of ∼15 kilometers beneath San Francisco and San Pablo bays. Velocity analyses indicate that this reflector marks the base of Franciscan assemblage rocks and the top of a mafic lower crust. Because this compositional contrast would imply a strong rheological contrast, this interface may correspond to a lower crustal detachment surface. If so, it may represent a subhorizontal segment of the North America and Pacific plate boundary proposed by earlier thermo-mechanical and geological models.

California↗