Geology Reports⌕ Search

Geology topics

Mitchell A. McAdoo

Publications and source records attributed to Mitchell A. McAdoo.

9 recordsLinked to original sources

Factors affecting the distribution of water-bearing fractures in the bedrock aquifers of West Virginia

Bedrock aquifers cover 23,601 square miles within the State of West Virginia and comprise 97.4 percent of the surficial area within the State; the remaining 2.6 percent (621 square miles) consists of alluvial sand-and-gravel and glacial outwash aquifers bordering the State’s major rivers. While West Virginia’s alluvial aquifers have been studied extensively, bedrock aquifers have only been characterized for studies completed in a few areas in Jefferson, McDowell, and Monroe Counties. Bedrock aquifers are water supplies for public supply, agriculture, industry, and residential homeowner use. In this study, the U.S. Geological Survey, in cooperation with the West Virginia Department of Environmental Protection Division of Water and Waste Management, provides a statewide assessment of the occurrence and distribution of fractures within bedrock aquifers of the State and the various topographic, physiographic, and lithologic influences controlling the occurrence and distribution of bedrock fractures. The results of this study provide an increased understanding of the distribution of fractures in bedrock aquifers in West Virginia and help to verify trends that have been suspected for many years but were never well documented or verified by data. The results confirmed that the density of fractures and those that were determined to be water bearing decrease significantly with depth. A statistically significant difference in the density of fractures was observed at a depth of 215 feet for wells in the Appalachian Plateaus Physiographic Province’s and in the Valley and Ridge Physiographic Province’s aquifers; a higher density of fractures and water-bearing fractures were above a depth of 215 feet than below that depth. This is an important consideration when drilling wells for residential, commercial, industrial, or agricultural water supply. Abandoned underground coal mines are commonly believed to form large pools of water in the interconnected mine entries in abandoned room and pillar coal mines. Such pools of water can and do exist in abandoned underground coal mines, but many mines lack open entries and are held up by overburden strata and pillars that can collapse and form aquifers comprised of vast interconnected rubble zones (gob), especially in older mines. Data assessed for this study showed that shale-corrected values of effective porosity for limestone aquifers in West Virginia had a median value of 2 percent and an average value of 4 percent and generally are mineralized with low effective porosity. Argillaceous or sandy limestone has a median shale-corrected porosity of 4 percent and an average shale-corrected porosity of 5 percent. The median and average shale-corrected porosity of sandstone aquifers was estimated to be 14 percent, but the median shale-corrected porosity for argillaceous or calcareous sandstone was 5 percent and the average shale-corrected porosity for argillaceous or calcareous sandstone was 6 percent. Even though shale has a relatively high total sonic porosity compared to other lithologies, shale and siltstone had relatively low shale-corrected porosity, ranging from 0 to 2 percent. Well yields were previously documented to be highest in valley settings, lowest on hilltops, and intermediate on hillsides. Transmissivity data provided by this study confirm this general pattern within the Appalachian Plateaus Province; however, the Valley and Ridge Province does not follow this pattern. While still lowest on hilltop settings, the highest well yields were in hillside settings. The trend for the Valley and Ridge Province was likely skewed because of 9 high-yield wells specifically targeting deeper thin limestone units, such as the Tonoloway and Helderberg Limestones, at depths with transmissivity in excess of 2,000 feet squared per day in Mineral County, West Virginia, or targeting karst aquifers in Berkeley, Jefferson, or Greenbrier Counties, West Virginia. Finally, water-bearing fractures have been hypothesized to comprise a small number of all fractures within a typical bedrock well in West Virginia. Data collected for this study support this theory. A total of 3,403 fractures were identified during this study; 3,151 (92.6 percent) of those fractures are low-transmissive, and only 252 (7.4 percent) fractures are water-bearing. Even though a well may contain many fractures, less than 8 percent are considered water-bearing fractures.

West Virginia↗

Municipal and industrial wastewater treatment plant effluent contributions to per- and polyfluoroalkyl substances in the Potomac River: A basin-scale measuring and modeling approach

Managing per- and polyfluoroalkyl substances (PFAS) in water resources requires a basin-scale approach. Predicted environmental concentrations (PEC) and stream-vulnerability scores for PFAS were determined for the Potomac River watershed in the eastern United States. Approximately 15% of stream reaches contained municipal and/or industrial wastewater treatment plant (WWTP) discharges that are presumptive PFAS sources, comprising from <1 to >90% of streamflow. Mean annual PEC, based on the summed concentrations of eight PFAS detected in WWTP effluents (ΣPFAS PEC ), for all stream reaches in the watershed was 3.8 ng L –1 , and stream reaches impacted by WWTP had perfluorooctanoate (PFOA) and perfluorooctanesulfonate (PFOS) PEC of 0.39 and 0.14 ng L –1 . For locations where measured-environmental concentrations (MEC) were determined, municipal and industrial WWTP contributed 7.8% (0 to 65%) of the total annual streamflow and MEC were greater than PEC in 99% of the samples, indicating additional potential PFAS sources. The mean ΣPFAS PEC was 9.1 ng L –1 compared to a mean sum of PFAS MEC of 34 ng L –1 . Under mean-August low-flow, 17% and 9.4% of the water-supply intakes had maximum PFOA and PFOS PEC exceeding drinking water maximum contaminant levels.

Maryland, Pennsylvania, Virginia, West Virginia↗

Water-quality indicators of surface-water-influenced groundwater supplies in the Ohio River alluvial aquifer of West Virginia

The U.S. Geological Survey, in cooperation with the West Virginia Department of Health and Human Resources, studied surface-water-influenced groundwater supplies in the Ohio River alluvial aquifer of West Virginia for the purpose of understanding the influence of surface water on groundwater chemistry. Public groundwater supplies obtained from these aquifers receive substantial recharge from surface-water sources and are highly susceptible to degradation from water-soluble contaminants. Water samples were collected from 4 sites in the Ohio River and 23 groundwater wells in the alluvial aquifer from June 2019 to January 2020. Surface-water influence was assessed through characterization of groundwater quality, determination of recharge sources, estimation of groundwater age, and estimation of the fraction of Ohio River water entering groundwater pumped by wells in the alluvial aquifers. Hydrogeochemical processes controlling solute concentrations in the Ohio River alluvial aquifer were evaluated with multivariate statistical analysis and identified to be primarily controlled by redox processes, input from sources of salinity, and carbonate dissolution. Meteoric recharge from the Ohio River and precipitation on the alluvium are the main sources of water entering the aquifer. The age of groundwater in the system was determined to be primarily from a modern source. Groundwater samples from every well included in this study had detections for at least one geochemical indicator of surface-water influence, and every well was determined to be susceptible and vulnerable to contamination from surface sources. Results from binary mixing models and inverse geochemical models showed that sulfate, silica, and bicarbonate concentrations predict the fraction of Ohio River water entering alluvial wells for preliminary determination of surface-water influence when compared to fractions predicted using a numerical groundwater-flow model. In the absence of extensive analytes and geochemical or groundwater modeling capabilities, preliminary assessment of the fraction of Ohio River water entering groundwater wells in the Ohio River alluvium can be estimated for most sites using a linear relation between the equivalent ratio of bicarbonate to sulfate and the fraction of water computed by the average of the three geochemical models presented in this report. This approximation of the fraction of Ohio River water, coupled with information on the hydrogeological framework and geochemical indicators of surface-water influence, may be sufficient for preliminary assessment of surface-water influence in the absence of more detailed site information or reaction-transport models.

West Virginia↗

Hydrogeology, karst, and groundwater availability of Monroe County, West Virginia

Monroe County is in southeastern West Virginia, encompassing an area of 474 square miles. The area consists of karst and siliciclastic aquifers of Ordovician, Silurian, Devonian, and Mississippian age and is in parts of two physiographic provinces: the Valley and Ridge Province to the east of Peters Mountain, and the Appalachian Plateau Province to the west of Peters Mountain. This study was developed in response to inquiries from the Monroe County Commission requesting assessment of the water resources of the county to better understand the quantity of the county’s groundwater resources, for both current [2023] and future demand, and to provide information to support protection and management of the county’s valuable groundwater resources. Various products were developed for this study that provide knowledge with respect to water availability and contamination susceptibility of the karst aquifers within the county. U.S. Geological Survey (USGS) geologists conducted extensive geologic mapping in support of the project, producing (1) a countywide bedrock geologic map, (2) a countywide hydrogeologic map, and (3) a light detection and ranging (lidar)-derived countywide digital elevation model and associated sinkhole map. A significant part of this work was to map in detail the Greenbrier Group at the formation level, which prior to this study had only partially been completed. The report also includes (4) a description of the lithologic units identified as part of the geologic mapping process. U.S. Geological Survey hydrologists completed several additional products for the hydrology part of the effort, including development of (1) a countywide potentiometric surface (water-table) map, (2) a countywide base-flow stream assessment, (3) countywide water-budget estimates, (4) well log surveys for 15 wells to better understand subsurface controls on groundwater flow within the study area, (5) two groundwater tracer tests to better refine the groundwater divide from the northern and southern parts of the karst aquifer in Monroe County; and finally, based on all available data collected for the study including the potentiometric surface map, geologic map, current [2023] and legacy fluorometric groundwater tracer tests, and base-flow stream assessments, (6) groundwater-basin delineations were reassessed for principal groundwater basins within the Greenbrier aquifer. In Monroe County, four principal hydrogeologic settings produce large yields of water for residential, agricultural, and other uses. The most relied upon water-bearing zone with respect to current [2023] public water supply is from springs along Peters Mountain. These springs are derived from intervals of fractured sandstone and resultant alluvial deposits. Groundwater flows downslope through these permeable alluvial deposits and discharges at the contact with less permeable strata, such as the Reedsville Shale. The second most relied upon water-bearing zone in Monroe County is within the karstic Greenbrier Group aquifer, in which the basal Hillsdale Limestone overlies the less permeable Maccrady Shale. This geologic contact between the Hillsdale Limestone and Maccrady Shale is not only targeted as a source of water for agricultural supply but also is targeted as a source of water for residential supply. The third most relied upon water-bearing zone is composed of shallow perched aquifers within the Greenbrier Group. The discontinuous nature of these perched aquifers makes mapping their extent impossible, but they are related to permeable geologic strata, such as karstified limestones with solutionally enhanced permeability that overlies less permeable shale or chert bedrock. During geologic mapping of the county, several of these perched aquifers were documented in the Pickaway, Union, and Alderson Limestones. A fourth zone consists of springs from Ordovician carbonates at the base of Peters Mountain, which are influenced by sinking streams as well as upwelling along faults. In terms of water quantity, the most sustainable springs are those having deeper-sourced flows. Public supplies are a principal source of water used for residential and commercial supply in the region, accounting for 0.49 million gallons per day (Mgal/d) of fresh-water withdrawals (0.14 Mgal/d of groundwater and 0.35 Mgal/d of surface water) for residential and commercial use and serving 6,645 individuals (49.2 percent of the population). An estimated 6,861 people, (50.8 percent of the population) primarily rely on private wells or other unregulated sources, such as springs, and withdraw 0.55 Mgal/d of groundwater for their residential use. Public water supply in the region is primarily (71.4 percent) derived from springs and augmented by stream withdrawals (backup sources mainly during low-flow periods), with the remaining portion (28.6 percent) derived from groundwater withdrawals from wells. For rural residents, however, 100 percent of their withdrawals are derived from groundwater (wells or springs).

West Virginia↗

Groundwater quality in abandoned underground coal mine aquifers across West Virginia

Abandoned underground coal mine aquifers cover a large part of West Virginia and could supply substantial quantities of water for agricultural, industrial, residential, and public use. Several Federal, State, and academic institutions have studied the availability and quality of water stored in abandoned underground coal mine aquifers for a variety of applications, such as economic development, geothermal energy, aquaculture, and wastewater disposal. However, the spatial and stratigraphic controls on water quality produced from abandoned underground coal mine aquifers are still poorly constrained on a state-wide basis. In response to these knowledge gaps, the U.S. Geological Survey initiated a study, in cooperation with the West Virginia Department of Environmental Protection, to understand the applicability of using existing secondary source data for understanding water quality in abandoned underground coal mine aquifers across the State. Results from the calculation of net alkalinity indicated that Upper Pennsylvanian coal beds primarily produce net acidic waters and Lower Pennsylvanian coal beds primarily produce net alkaline waters. Multivariate statistical analysis of elemental data supports the conclusion that abandoned underground coal mine aquifers in the northern part of the State generally produce poor water quality and abandoned underground coal mine aquifers in southern West Virginia primarily produce good water quality. These results substantiate the potential benefits of leveraging abandoned underground coal mine aquifers as a multifaceted resource in West Virginia and can be used as a reconnaissance tool for water managers to characterize abandoned underground coal mine aquifers on a local scale.

West Virginia↗

Groundwater quality and geochemistry of the western wet gas part of the Marcellus Shale Oil and Gas Play in West Virginia

Thirty rural residential water wells in the wet gas region of the Marcellus Shale oil and gas play in northwestern West Virginia were sampled by the U.S. Geological Survey (USGS) in 2018, in cooperation with West Virginia State agencies, to analyze for a range of water-quality constituents, including major ions, trace metals, radionuclides, bacteria, and methane and other dissolved hydrocarbon gases. The groundwater-quality data collected for this study were used to assess the overall quality of groundwater in the study area in relation to public drinking-water standards. The groundwater-quality data were also evaluated with respect to geology, well depth, topographic setting, and proximity to oil and gas wells to identify possible relations to these factors. The presence of total coliform bacteria in groundwater is a potential indicator of surface contamination. The presence of Escherichia coli bacteria is indicative of fecal contamination of groundwater from either human or animal sources and may be considered an indicator of other related pathogens such as viruses. Total coliforms were detected in 26 of the 30 (87 percent) wells sampled. Eleven of the 30 (37 percent) wells sampled had detections of Escherichia coli bacteria. Sodium concentrations in 24 of 30 (80 percent) samples exceeded the U.S. Environmental Protection Agency (EPA) 20-milligram per Liter (mg/L) health-based value (HBV). Manganese, aluminum, and iron concentrations exceeded the EPA 50, 2.0, and 300 micrograms per liter (μg/L) secondary maximum contaminant level (SMCL) drinking-water standards at 14 (47 percent), 7 (23 percent), and 5 (17 percent) of the 30 wells sampled. Two of the 30 (7 percent) wells sampled had concentrations of manganese that exceeded the 300-μg/L USGS health-based screening level (HBSL). Arsenic concentrations at 7 of 30 (23 percent) wells sampled exceeded the 10-μg/L EPA maximum contaminant level (MCL) health-based drinking water standard. The EPA maximum contaminant level goal (MCLG) for arsenic is 0 μg/L and 29 of 30 wells sampled contained detectable concentrations of arsenic. None of the 30 wells sampled exceeded the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) 28-mg/L immediate action level (IAL) for methane in groundwater and only 1 of 30 (3 percent) sites exceeded the 10-mg/L OSMRE level of concern (LOC) for methane in groundwater. Of the 28 wells sampled for radon-222 all 28 (100 percent) exceeded the EPA proposed 300-picocuries per liter (pCi/L) MCL for radon. None of the samples exceeded the 4,000-pCi/L alternate maximum contaminant level (AMCL) which is applicable to public drinking water systems that have adopted radon mitigation programs. Wilcoxon Signed Rank Tests indicated statistically significant differences at a 95 percent confidence interval (p less than 0.05) in radium-226, barium, and ethane groundwater concentrations with respect to the density of oil and gas wells present within a 500-meter (m) radius around the rural residential wells sampled for the study. Samples from residential wells that had four or fewer oil and gas wells in the surrounding 500-m radius had statistically lower concentrations of radium-226, bromide, and ethane than samples from residential wells sampled that had five or more oil and gas wells in the surrounding 500-m radius. Given the available data, the relationship between concentrations of radium-226, bromide, and ethane for wells sampled in this study and oil and gas development or natural geochemical processes is not clear. Groundwater-age tracers (chlorofluorocarbons, tritium, and sulfur hexafluoride) were sampled at 17 of the 30 wells. All 17 samples contained a fraction of young, post-1950s groundwater. Many of the groundwater samples collected for this study have high calcium to sodium ratios and low total dissolved solids concentrations, indicating they are dominated by recently recharged water. A subset of samples had chloride to bromide mass ratios between 70 and 200, indicating that deep Appalachian basin brines mixed with the shallow groundwater. For most of the samples in this study, the C 1 through C 6 hydrocarbons have characteristics that reflect a biogenic gas signature that has, to varying degrees, undergone oxidation processes during transport. None of the samples show a characteristic thermogenic cracking pattern among the hydrocarbon ratios.

West Virginia↗

Occurrence of per- and polyfluoroalkyl substances and inorganic analytes in groundwater and surface water used as sources for public water supply in West Virginia

Per- and polyfluoroalkyl substances (PFAS) are widely observed anthropogenic compounds found in water supplies worldwide and increasingly linked with adverse health effects in humans. In 2019, the West Virginia Legislature recognized the contamination risk to public source-water supplies posed by PFAS and passed a resolution that required a statewide PFAS study. The purpose of the resolution was to understand the occurrence and distribution of PFAS contamination throughout the State’s rivers, lakes, and groundwater aquifers. The U.S. Geological Survey has worked in cooperation with the West Virginia Department of Environmental Protection and West Virginia Department of Health and Human Resources to collect raw-water samples at 279 public-water systems across West Virginia. Public-water systems sampled for this study were identified by the West Virginia Department of Health and Human Resources and included all community water systems in the State and all daycares and schools that operate their own water systems. Raw source water was sampled for both groundwater and surface-water sites at the first available tap in the public-water system, prior to any treatment. One hundred and seventy-three samples were collected from groundwater sources and 106 samples were collected from surface-water sources. Parameters collected at the time of sampling included pH, specific conductance, water temperature, dissolved oxygen, turbidity, and alkalinity. PFAS was analyzed at all 279 sites, major ions and trace elements were analyzed at 272 sites, and nutrients were analyzed at 270 sites. The type of source water used for public supply in West Virginia is generally dependent on geology with more groundwater sites sampled in high-yield aquifers such as karst and alluvium. Surface-water sites were more evenly distributed throughout the State and are often the only source used in areas underlain by lower-yielding fractured-rock aquifers. Twenty-four percent of the sites sampled for this study had at least 1 PFAS detected, 47 of which were in groundwater sources and 20 in surface-water sources. Five sites exceeded the U.S. Environmental Protection Agency’s health advisory for combined perfluorooctanoate and perfluorooctanesulfonate concentrations of 70 nanograms per liter. These sites were located in highly susceptible karst and alluvial groundwater aquifers on the east and west sides of the State. Higher PFAS concentrations were more commonly found in groundwater than surface-water sources, and high concentrations and PFAS detections were generally concentrated in the Ohio River Valley and West Virginia’s eastern panhandle. PFAS was rarely detected in groundwater sites in fractured-rock aquifers and abandoned underground coal-mine aquifers in the Appalachian Plateaus Physiographic Province had very little PFAS detected. These data represent a baseline summary of source water in West Virginia. Additional studies may be needed to understand exposure to private homeowners with domestic-water sources, variability of PFAS concentrations over time, and PFAS in finished drinking water as evaluated by current and future drinking-water regulations.

West Virginia↗

Groundwater quality and geochemistry of West Virginia’s southern coal fields

Coal mining has been the dominant industry and land use in West Virginia’s southern coal fields since the mid-1800s. Mortality rates for a variety of serious chronic conditions, such as diabetes, heart disease, and some forms of cancer in Appalachian coal mining regions, are higher than in areas lacking substantial coal mining activity within the Appalachian Region or elsewhere in the United States. Causes of the increased mortality and morbidity are not clear, but poor diet, high rates of smoking, socioeconomic factors, and the quality of groundwater used by area residents are all possible contributing factors. This study was conducted by the U.S. Geological Survey in cooperation with the West Virginia Department of Health and Human Resources and the West Virginia Department of Environmental Protection, with grant support from the Centers for Disease Control and Prevention (CDC) to assess the quality of groundwater in southern West Virginia. The data from this assessment of groundwater quality may be used by the CDC and other agencies to potentially investigate the role or lack thereof of groundwater quality with respect to mortality and morbidity rates in the region. The study was conducted in a region where a high density of current or past coal mining combined with a lack of advanced sewage treatment could affect concentrations of commonly occurring constituents plus contaminants, including nitrate, trace metals, major ions, indicator bacteria, radon, hydrogen sulfide, and dissolved hydrocarbons. Because rural residential wells and mine outfalls are considered private sources of water in the region, and are therefore unregulated and unmonitored, water-quality data are sparse. To fill the data gap and assess the groundwater quality in the region, water-quality samples were collected from 60 sites in a 10-county area. The 60 sites sampled included 46 rural residential homeowner wells and 14 mine outfall discharges used for residential supply. For this study, all samples were collected prior to any filtration or other treatments, typically at the pressure tank, and are indicative of total and dissolved constituents in the untreated water. Generally, data for the 60 sites indicate that most waters sampled do not exceed thresholds for most U.S. Environmental Protection Agency (EPA) drinking-water standards and U.S. Geological Survey (USGS) drinking-water screening criteria. However, there were several notable exceptions. Turbidity exceeded the 5-Nephelometric Turbidity Unit (NTU) EPA treatment technique (TT) drinking-water standard in 14 of 60 (23 percent) sites sampled and exceeded the 1-NTU TT standard in 51 of 60 (85 percent) sites sampled. Turbidity is common in many wells in southern West Virginia and may be attributed to iron oxyhydroxide precipitates, sediment carried into the aquifers from the shallow soil zone due to improperly constructed or cased wells or transported to the aquifer in shallow stress-relief fracture zones or through permeable bedding-plane partings. For the sites sampled, 31 of 60 (52 percent) had pH values at, above, or below the upper and lower range of the EPA Secondary Maximum Contaminant Level (SMCL, 6.5–8.5 standard units). Of those 31 sites, 28 (90 percent) were indicative of acidic corrosive water and 3 (10 percent) were indicative of alkaline water. The Langelier Saturation Index (LSI), which is a measure of the corrosivity of the water, was computed for all sites sampled for the study. Eighty-two percent of the sites sampled had waters that were classified as corrosive, based on a LSI less than −0.5. Corrosive water has the potential to leach lead, copper, and other metals from lead, copper, galvanized, or lead-tin soldered connections in water lines. The chloride to sulfate mass ratio also was assessed with the alkalinity to indicate the potential to promote galvanic corrosion (PPGC) of water lines and plumbing fixtures. Only one of the sites (1.7 percent) classified as a corrosive water site, had a PPGC considered high; the remaining sites were classified as having either a moderate (53.3 percent) or low (45 percent) PPGC. Therefore, the type of plumbing systems sampled for this study may be affected by corrosive water, but the potential for leaching trace metals and other constituents from residential plumbing systems containing older galvanized pipes or lead-tin soldered copper pipes is moderate to low. The indicator bacteria total coliform and Escherichia coli ( E. coli ) also were detected in groundwater samples to varying degrees. Total coliforms, which are a broad class of indicator bacteria, are common in groundwater in southern West Virginia and were detected in 39 of the 60 sites (65 percent) sampled. The presence of total coliform bacteria is a potential indicator of surface contamination, due to improperly constructed or cased wells, or infiltration of soil or other surface contaminants into the aquifer or well bore. E. coli bacteria, however, are much more indicative of fecal contamination of groundwater from either human or animal sources, and 14 of the 60 (23 percent) sites sampled had detections of E. coli . Although only a few strains of E. coli are known pathogens, their presence in groundwater may be an indicator of other related pathogens such as viruses and should be regarded as a serious potential issue. Water treatment such as chlorination, ozonation, or ultraviolet light may be appropriate to kill potential pathogenic bacteria or viruses in the source water. Manganese and iron were prevalent contaminants in the groundwater samples collected for this study, with 30 of 60 (50 percent) sites analyzed for manganese and 25 of 60 (42 percent) sites analyzed for iron exceeding the proposed 50- and 300-micrograms per liter (µg/L) SMCL drinking-water standards, respectively, for aesthetic criteria such as taste, odor, or staining of plumbing fixtures. Fourteen of the 60 sites sampled (23 percent) had concentrations of manganese that exceeded the 300-µg/L USGS health-based screening level, and 1 site exceeded the 1,600-µg/L EPA drinking-water equivalent level, which is based on a lifetime exposure level. Sodium is another common constituent in groundwater within the study area. Sodium has an EPA health-based value (HBV) of 20 milligrams per liter (mg/L) for individuals who are on a sodium-restricted diet for blood pressure or other health reasons. Sodium concentrations exceeded the 20-mg/L EPA HBV in 27 of 60 (45 percent) samples. Radon, a naturally occurring carcinogenic radioactive gas known to cause lung cancer, was detected at concentrations at or exceeding the proposed 300-picocuries per liter (pCi/L) EPA Maximum Contaminant Level (MCL) in 12 of the 60 (20 percent) sites sampled. Sites with radon gas concentrations exceeding the 300-pCi/L proposed MCL have the potential for airborne concentrations of radon to exceed the 4-pCi/L indoor air standard. Inhalation of radon can cause lung cancer, and the 4-pCi/L indoor air standard is based on an inhalation standard. Therefore, homeowners whose wells have radon gas concentrations exceeding 300 pCi/L may be advised to have their indoor air tested to determine if indoor air concentrations exceed the 4-pCi/L indoor air standard established by the EPA. Various factors were analyzed statistically and graphically to determine whether they have an influence on groundwater quality within the study area, including topographic setting, well depth, type of mining (surface or underground), type of site (well or mine outfall), and geologic formation. Only geologic formation and the type of site sampled had strong statistical correlations with one or more of the constituents of concern for this study. The overall chemistry of outfalls (mine outfalls) and wells was significantly different, with a much higher dissolved oxygen content in outfalls than in wells. The dissolved oxygen content is the primary component driving the oxidation and reduction of minerals, and the precipitation of minerals that are saturated or super saturated with respect to various cations and anions. Median dissolved oxygen concentrations for the outfalls sampled was 8.75 mg/L, and only 0.4 mg/L for the wells sampled. Median concentrations of sulfate and selenium were much higher in waters from the outfalls sampled, with median concentrations of 73.75 mg/L and 2.35 µg/L, respectively, compared to the wells sampled, which had median concentrations of 18.3 mg/L and less than (<) the 0.05-µg/L method detection limit, respectively. The maximum selenium concentration was for a well, with a concentration of 16.6 µg/L. The geochemical processes that control sulfate and selenium concentrations in groundwater are similar and are the result of the oxidation of sulfide minerals such as pyrite and ferroselite. Iron and manganese concentrations were elevated in most of the wells sampled, with median concentrations of 269.5 and 124.5 µg/L, respectively, but were rarely detected in the outfalls sampled, with median concentrations of < 4.0 and < 0.4 µg/L, respectively. The difference in iron and manganese between wells and outfalls is indicative of the role of dissolved oxygen on processes controlling groundwater chemistry in the region. Three principal geologic formations were assessed for the study, and the overall chemistry for the Pocahontas, New River, and Kanawha Formations varied substantially with respect to several constituents. Concentrations of calcium, magnesium, and total dissolved solids were highest for sites sampled in the Pocahontas Formation, with median concentrations of 41.9, 18.6, and 312 mg/L, respectively. For constituents that are commonly associated with mining activity, the highest concentrations were for sites sampled in the New River Formation, with median concentrations of iron and manganese of 2,450 µg/L and 482 µg/L, respectively, and a median pH of 6.35 standard units. Concentrations of barium also were elevated in samples collected from sites in the New River Formation, with a median barium concentration of 184 µg/L. The source of the barium is not fully known but may be associated with commingling of shallow groundwater with deeper brines or dissolution of the mineral barite. The highest median sulfate concentrations were from sites sampled in the Pocahontas Formation, with a median concentration of 64.0 mg/L. Of the 12 sites at or exceeding the 300-pCi/L proposed drinking-water standard for radon, 8 (67 percent of MCL exceedances) were for sites deriving water from the Kanawha Formation, 3 (25 percent of MCL exceedances) were for sites deriving water from the New River Formation, and only 1 site was for water from the Pocahontas Formation (8 percent of proposed MCL exceedances). Dissolved hydrocarbons, including methane, ethane, propane, propene, n - and i -butane, 1-butene, n - and i -pentane, pentane, 2- and 3-ethyl pentane, hexane, and benzene were analyzed in samples collected from 59 of the 60 sites to assess the potential occurrence and sources of these trace gases in groundwater within the study area. Results of the analysis indicate that most of the gas is of shallow biogenic origin, possibly associated with coal-bed methane, but a subset of samples has a gas signature and a chloride to bromide ratio indicative of potential mixing with deeper thermogenic gases. Only 2 of the 59 (3.3 percent) sites sampled had concentrations of methane gas, which is a highly combustible and explosive gas, exceeding the 10 milligrams per kilogram level of concern established by the U.S. Office of Surface Mining Reclamation and Enforcement. Principal components analysis was used to assess the primary geochemical processes occurring in the aquifers sampled. The first principal component had significant positive loadings for bromide, chloride, silica, ammonia, barium, iron, manganese, and arsenic, and significant negative loadings for dissolved oxygen, potassium, nitrate, and uranium, and reflects reduction and oxidation (redox) processes occurring in deeper anoxic groundwater or shallow oxic groundwater. The strong positive loadings for iron, manganese, barium, and arsenic are correlated with reducing conditions often found deeper in the aquifer. More oxic water is correlated with oxidation of nitrogen species to nitrate and environmental mobilization of uranium and sulfate in shallow wells and mine outfalls.

West Virginia↗

Groundwater-quality data associated with abandoned underground coal mine aquifers in West Virginia, 1973-2016: Compilation of existing data from multiple sources

This report describes a compilation of existing water-quality data associated with groundwater resources originating from abandoned underground coal mines in West Virginia. Data were compiled from multiple sources for the purpose of understanding the suitability of groundwater from abandoned underground coal mines for public supply, industrial, agricultural, and other uses. This compilation includes data collected for multiple individual studies conducted from July 13, 1973 through September 7, 2016. Analytical methods varied by the time period of data collection and requirements of the independent studies.This project identified 770 water-quality samples from 294 sites that could be attributed to abandoned underground coal mine aquifers originating from multiple coal seams in West Virginia.

West Virginia↗