Geology topics
Publications and source records attributed to Mark J. Pawlewicz.
Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 0.78 billion barrels of unconventional oil, 23.5 trillion cubic feet of unconventional gas, and 0.88 billion barrels of natural gas liquids in the Sabinas Basin, Burgos Basin, and Tampico-Misantla Basin provinces of northeast Mexico.
Using a geology-based assessment methodology, the U.S. Geological Survey estimated means of 11 million barrels of potential shale-oil and 320 billion cubic feet of shale-gas resources in Silurian shales of Jordan.
We used Rock-Eval pyrolysis and vitrinite reflectance to examine the petroleum source potential of rock samples from the Sheep Creek 1 well in the Susitna basin of south-central Alaska. The results show that Miocene nonmarine coal, carbonaceous shale, and mudstone are potential sources of hydrocarbons and are thermally immature with respect to the oil window. In the samples that we studied, coals are more organic-rich and more oil-prone than carbonaceous shales and silty mudstones, which appear to be potential sources of natural gas. Lithologically similar rocks may be present in the deeper parts of the subsurface Susitna basin located west of the Sheep Creek 1 well, where they may have been buried deeply enough to generate oil and (or) gas. The Susitna basin is sparsely drilled and mostly unexplored, and no commercial production of hydrocarbons has been obtained. However, the existence of potential source rocks of oil and gas, as shown by our Rock-Eval results, suggests that undiscovered petroleum accumulations may be present in the Susitna basin.
A 130-foot-thick Cambrian black shale sampled from a core between 11,150 and 11,195 feet in the Exxon No. 1 Smith well in Wayne County, W. Va., has been identified as a good to very good source rock. The black shale is located in the Middle Cambrian Rogersville Shale of the Conasauga Group. Total organic carbon (TOC) values of four samples that range from 1.2 to 4.4 weight percent (average 2.6 weight percent) are the highest reported to date in the pre-Knox section of the Rome trough. Although the samples are probably in the zone of gas generation based on their low hydrogen index values (55 to 63) and temperature maximum of second hydrocarbon peak (S 2 ) values of about 465°C, first hydrocarbon peak (S 1 ) values of 0.81 to 2.71 indicate that they contain free extractable hydrocarbons. A bitumen sample extracted from the Rogersville Shale is characterized by (1) a broad spectrum of n -alkanes from n -C 11 through n -C 30 , (2) strong odd-carbon predominance in the n -C 13 to n -C 19 range, and (3) small but detectable amounts of isoprenoids pristane and phytane. The strong odd-carbon predominance of the n -C 15 to n -C1 9 n-alkanes is commonly attributed to the Ordovician alga Gloeocapsomorpha prisca . This occurrence of G. prisca is among the first to be reported in Cambrian rocks. Thin black shale beds collected from the Lower to Middle Cambrian Rome Formation in the Texaco No. 1 Kirby well in Garrard County, Ky., have TOC values as high as 3.2 percent, hydrogen index values as high as 417, and bitumen extract characteristics similar to the Rogersville Shale. The bitumen extract from the Rogersville Shale compares very closely with oils or condensates from Cambrian reservoirs in the Carson Associates No. 1 Kazee well, Homer gas field, Elliott County, Ky.; the Inland No. 529 White well, Boyd County, Ky.; and the Miller No. 1 well, Wolfe County, Ky. These favorable oil-source rock correlations suggest a new petroleum system in the Appalachian basin that is characterized by a Conasauga Group source rock and Rome Formation and Conasauga Group reservoirs. This petroleum system probably extends along the Rome trough from eastern Kentucky to at least central West Virginia.
The Bighorn Basin is one of many structural and sedimentary basins that formed in the Rocky Mountain foreland during the Laramide orogeny, a period of crustal instability and compressional tectonics that began in latest Cretaceous time and ended in the Eocene. The basin is nearly 180 mi long, 100 mi wide, and encompasses about 10,400 mi 2 in north-central Wyoming and south-central Montana. The basin is bounded on the northeast by the Pryor Mountains, on the east by the Bighorn Mountains, and on the south by the Owl Creek Mountains). The north boundary includes a zone of faulting and folding referred to as the Nye-Bowler lineament. The northwest and west margins are formed by the Beartooth Mountains and Absaroka Range, respectively. Important conventional oil and gas resources have been discovered and produced from reservoirs ranging in age from Cambrian through Tertiary. In addition, a potential unconventional basin-centered gas accumulation may be present in Cretaceous reservoirs in the deeper parts of the basin. It has been suggested by numerous authors that various Cretaceous marine shales are the principal source rock for these accumulations. Numerous studies of various Upper Cretaceous marine shales in the Rocky Mountain region have led to the general conclusion that these rocks have generated or are capable of generating oil and (or) gas. In recent years, advances in horizontal drilling and multistage fracture stimulation have resulted in increased exploration and completion of wells in Cretaceous marine shales in other Rocky Mountain Laramide basins that were previously thought of only as hydrocarbon source rocks. Important parameters controlling hydrocarbon production from these shale reservoirs include: reservoir thickness, amount and type of organic matter, and thermal maturity. The purpose of this report is to present maps and a cross section showing levels of thermal maturity, based on vitrinite reflectance (R o ), for selected Upper Cretaceous marine shales in the Bighorn Basin.
The Wind River Basin is a large Laramide (Late Cretaceous through Eocene) structural and sedimentary basin that encompasses about 7,400 square miles in central Wyoming. The basin is bounded by the Washakie Range and Owl Creek and southern Bighorn Mountains on the north, the Casper arch on the east and northeast, and the Granite Mountains on the south, and Wind River Range on the west. The purpose of this report is to present new vitrinite reflectance data collected mainly from Cretaceous marine shales in the Wind River Basin to better characterize their thermal maturity and hydrocarbon potential.
The Wind River Basin is a large Laramide (Late Cretaceous through Eocene) structural and sedimentary basin that encompasses about 7,400 square miles in central Wyoming. The basin is bounded by the Washakie Range, Owl Creek, and southern Bighorn Mountains on the north, the Casper arch on the east and northeast, the Granite Mountains on the south, and the Wind River Range on the west. Important conventional and unconventional oil and gas resources have been discovered and produced from reservoirs ranging in age from Mississippian through Tertiary. It has been suggested that various Upper Cretaceous marine shales are the principal hydrocarbon source rocks for many of these accumulations. Numerous source rock studies of various Upper Cretaceous marine shales throughout the Rocky Mountain region have led to the conclusion that these rocks have generated, or are capable of generating, oil and (or) gas. With recent advances and success in horizontal drilling and multistage fracture stimulation there has been an increase in exploration and completion of wells in these marine shales in other Rocky Mountain Laramide basins that were traditionally thought of only as hydrocarbon source rocks. Important parameters that control hydrocarbon production from shales include: reservoir thickness, amount and type of organic matter, and thermal maturity. The purpose of this report is to present maps and a structural cross section showing levels of thermal maturity, based on vitrinite reflectance (Ro), for Upper Cretaceous marine shales in the Wind River Basin.
The Bighorn Basin is a large Laramide (Late Cretaceous through Eocene) structural and sedimentary basin that encompasses about 10,400 square miles in north-central Wyoming and south-central Montana. The purpose of this report is to present new vitrinite reflectance data collected from Cretaceous marine shales and coals in the Bighorn Basin to better characterize the thermal maturity and petroleum potential of these rocks. Ninety-eight samples from Lower Cretaceous and lowermost Upper Cretaceous strata were collected from well cuttings from wells stored at the U.S. Geological Survey (USGS) Core Research Center in Lakewood, Colorado.
In 2002, the U.S. Geological Survey (USGS) assessed the technically recoverable, undiscovered coalbed-gas resources in the Appalachian basin and Black Warrior basin Assessment Provinces as about 15.5 trillion cubic feet. Although these resources are almost equally divided between the two areas, most of the production occurs within relatively small areas within these Provinces, where local geological and geochemical attributes have resulted in the generation and retention of large amounts of methane within the coal beds and have enhanced the producibility of the gas from the coal. In the Appalachian basin, coalbed methane (CBM) tests are commonly commercial where the cumulative coal thickness completed in wells is greater than three meters (10 ft), the depth of burial of the coal beds is greater than 100 m (350 ft), and the coal is in the thermogenic gas window. In addition to the ubiquitous cleating within the coal beds, commercial production may be enhanced by secondary fracture porosity related to supplemental fracture systems within the coal beds. In order to release the methane from microporus coal matrix, most wells are dewatered prior to commercial production of gas. Two Total Petroleum Systems (TPS) were defined by the USGS during the assessment: the Pottsville Coal-bed gas TPS in Alabama, and the Carboniferous Coal-bed Gas TPS in Pennsylvania, Ohio, West Virginia, eastern Kentucky, Virginia, Tennessee, and Alabama. These were divided into seven assessment units, of which three had sufficient data to be assessed. Production rates are higher in most horizontal wells drilled into relatively thick coal beds, than in vertical wells; recovery per unit area is greater, and potential adverse environmental impact is decreased.
The U.S. Geological Survey (USGS) recently assessed the undiscovered oil and gas potential of the Permian Basin Province of west Texas and southeast New Mexico. The assessment was geology based and used the total petroleum system concept. The geologic elements of a total petroleum system are petroleum source rocks (quality, source rock maturation, generation, and migration), reservoir rocks (sequence stratigraphy, petrophysical properties), and traps (trap formation and timing). This study assessed potential for technically recoverable resources in new field discoveries only; field growth (or reserve growth) of conventional oil and gas fields was not included. Using this methodology, the U.S. Geological Survey estimated a mean of 41 trillion cubic feet of undiscovered natural gas and a mean of 1.3 billion barrels of undiscovered oil in the Permian Basin Province.
The U.S. Geological Survey (USGS) recently assessed the undiscovered oil and gas potential of the West Greenland-East Canada Province as part of the USGS Circum-Arctic Oil and Gas Resource Appraisal effort. The West Greenland-East Canada Province is essentially the offshore area between west Greenland and east Canada and includes Baffin Bay, Davis Strait, Lancaster Sound, and Nares Strait west of and including Kane Basin. The tectonic evolution of the West Greenland-East Canada Province led to the formation of several major structural domains that are the geologic basis for the five assessment units (AU) defined in this study. The five AUs encompass the entire province. Each AU was assessed in its entirety for undiscovered, technically recoverable (assuming absence of sea ice) oil and gas resources, but the assessment results reported here are only for those portions of each AU that are north of the Arctic Circle, as that latitude defines the area of the Circum-Arctic oil and gas assessment.
The U.S. Geological Survey (USGS) recently assessed the undiscovered oil and gas potential of the West Siberian Basin Province in Russia as part of the USGS Circum-Arctic Resource Appraisal program. This province is the largest petroleum basin in the world and has an areal extent of about 2.2 million square kilometers. It is a large rift-sag feature bounded to the west by the Ural fold belt, to the north by the Novaya Zemlya fold belt and North Siberian Sill, to the south by the Turgay Depression and Altay-Sayan fold belt, and to the east by the Yenisey Ridge, Turukhan-Igarka uplift, Yenisey-Khatanga Basin, and Taimyr High. The West Siberian Basin Province has a total discovered oil and gas volume of more than 360 billion barrels of oil equivalent (Ulmishek, 2000). Exploration has led to the discovery of tens of giant oil and gas fields, including the Urengoy gas field with more than 3500 trillion cubic feet of gas reserves and Samotlar oil field with reserves of nearly 28 billion barrels of oil (Ulmishek, 2003). This report summarizes the results of a reassessment of the undiscovered oil and gas potential of that part of the province north of the Arctic Circle; a previous assessment that included the entire province was completed in 2000 (Ulmishek, 2000). The total petroleum system (TPS) and assessment units (AU) defined by the USGS for the assessments in 2000 were adopted for this assessment. However, only those parts of the Aus lying wholly or partially north of the Arctic Circle were assessed for this study.
Explore the source record for details and available documents.
Introduction The purpose of the U.S. Geological Survey's (USGS) National Oil and Gas Assessment is to develop geologically based hypotheses regarding the potential for additions to oil and gas reserves in priority areas of the United States. The USGS recently completed an assessment of undiscovered oil and gas potential of the Cambrian-Ordovician carbonate rocks, the Chattanooga and Floyd Shales, and the Pottsville Formation coals in the Black Warrior Basin Province in northeastern Mississippi and northwestern Alabama in the Gulf Coast Region. The Cambrian-Ordovician carbonate rocks, the Chattanooga and Floyd Shales, and the Pottsville Formation coals are important because of their potential for natural gas resources. This assessment is based on geologic principles and uses the total petroleum system concept. The geologic elements of a total petroleum system include hydrocarbon source rocks (source rock maturation, hydrocarbon generation and migration), reservoir rocks (sequence stratigraphy and petrophysical properties), and hydrocarbon traps (trap formation and timing). The USGS used this geologic framework to define two total petroleum systems and three assessment units. All three assessment units were quantitatively assessed for undiscovered oil and gas resources.
The Bighorn Basin is a large Laramide (Late Cretaceous through Eocene) structural and sedimentary basin that encompasses about 10,400 mi2 in north-central Wyoming and south-central Montana (fig. 1). Important conventional oil and gas resources have been discovered and produced from reservoirs ranging in age from Cambrian through Tertiary (Fox and Dolton, 1989, 1996a, b; De Bruin, 1993). In addition, a potential unconventional basin-centered gas accumulation may be present in Cretaceous reservoirs (Johnson and Finn, 1998; Johnson and others, 1999). The purpose of this report is to present new vitrinite reflectance data to be used in support of the U.S Geological Survey’s assessment of undiscovered oil and gas resources of the Bighorn Basin. These new data supplement previously published data by Nuccio and Finn (1998), and Yin (1997), and lead to a better understanding and characterization of the thermal maturation and burial history of potential source rocks. Eighty-nine samples of Cretaceous and Tertiary strata (fig. 2) were collected and analyzed—15 samples were from outcrops around the margins of the basin and 74 samples were well cuttings (fig. 1). Forty-one of the samples were shale, two were carbonaceous shale, and the remainder from coal. All samples were analyzed by vitrinite reflectance to determine levels of thermal maturation. Preparation of samples for reflectance analysis required (1) crushing the larger pieces into 0.25-to 1-mm pieces, (2) casting the pieces with epoxy in pre-cut and drilled plugs, and (3) curing the samples overnight. Subsequently, a four-step grinding and polishing process was implemented that included sanding with progressively finer sandpaper (60 and 600 grit) followed with a two-step polishing process (0.3 and 0.05 micron). Vitrinite reflectance measurements were determined at 500 X magnification using plane-polarized incident white light and a 546-nm monochromatic filter in immersion oil. For samples containing sufficiently high quality vitrinite, at least 25 measurements were recorded. For samples of poorer quality, either due to a poor polish or to the presence of mineral or other inorganic material, fewer measurements were recorded. Analytical results are given in tables 1 and 2.
Introduction: The Wind River Basin is a large Laramide (Late Cretaceous through Eocene) structural and sedimentary basin that encompasses about 7,400 mi2 in central Wyoming. The basin boundaries are defined by fault-bounded Laramide uplifts that surround it, including the Owl Creek and Bighorn Mountains to the north, Wind River Range to the west, Granite Mountains to the south, and Casper Arch to the east. The purpose of this report is to present new vitrinite reflectance data to be used in support of the U.S Geological Survey assessment of undiscovered oil and gas resources of the Wind River Basin. One hundred and nineteen samples were collected from Jurassic through Tertiary rocks, mostly coal-bearing strata, in an effort to better understand and characterize the thermal maturation and burial history of potential source rocks.
Explore the source record for details and available documents.
Introduction This digitally compiled map includes geology, geologic provinces, and oil and gas fields of Europe including Turkey. The maps are part of a worldwide series of maps on CD-ROM released by the U.S. Geological Survey's World Energy Project. The goal of the project is to assess the undiscovered, technically recoverable oil and gas resources of the world. For data management purposes the world was divided into eight energy regions corresponding approximately to the economic regions of of the world as defined by the U.S. Department of State. Europe (Region 4) includes Albania, Andorra, Austria, Belgium, Bosnia and Herzegovina, Bulgaria, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Liechtenstein, Luxembourg, The Former Yugoslav Republic of Macedonia, Malta, Monaco, Netherlands, Norway, Poland, Portugal, Romania, San Marino, Serbia and Montenegro, Slovakia, Slovenia, Spain, Sweden, Switzerland, United Kingdom and Vatican. The depicted portion of Region 2 includes Turkey.