Geology topics

M. A. Fisher

Publications and source records attributed to M. A. Fisher.

At least 19 recordsLinked to original sources

USGS2012

The collision zone between the North d'Entrecasteaux Ridge and the New Hebrides island arc. 2. Structure from multichannel seismic data

The d'Entrecasteaux zone (DEZ) collides with the central New Hebrides island arc and consists of two subparallel ridges that strike east-west, stand 1–2 km above the surrounding oceanic plate, and subduct obliquely (15°) northward beneath the arc. Rocks dredged from the north ridge as well as reflections evident in multichannel seismic reflection data indicate that this ridge has a volcanic origin. Crystalline volcanic rocks are common along the lower flank of the ridge, but sedimentary, probably volcaniclastic, rock caps the ridge. Seismic reflection data collected over the lower arc slope reveal that mass wasting deposits locally make up most of the accretionary wedge. These deposits appear to form discrete bodies, suggesting that mass wasting occurred episodically. Large anticlines and thrust faults having large vertical separation are not readily evident where the colliding ridge intersects the arc slope; apparently, slope rocks have low strength so that mass wasting deposits formed instead of large-relief structures. Mass wasting is thought to occur as the accretionary wedge is uplifted in response to the northward oblique subduction of the north ridge. The toe of the north ridge flank marks an abrupt transition in the lithologies that make up the footwall of the interplate decollement. Footwall lithologies change from ocean basin to volcaniclastic ridge material, and this transition probably marks a discontinuity in friction along the decollement or in rock mechanical properties because north of the transition, thrust faults deform the accretionary wedge whereas south of the transition, steep reverse faults crosscut the wedge and pierce the north flank of the ridge. This piercement means that the decollement at least locally lies within the ridge and that ridge material exotic to the New Hebrides arc may be incorporated into the accretionary wedge.

Journal of Geophysical Research↗

USGS2012

Seismic reflection/refraction mapping of faulting and regional dips in the eastern Alaska Range

We present the results of a Trans‐Alaska Crustal Transect (TACT) investigation of the upper 2–5 km of the eastern Alaska Range in the vicinity of the Denali fault based on seismic reflection/refraction data, laboratory measurements of rock velocities, and structural mapping. The Denali fault is a major dextral slip structure mappable for more than 2000 km separating the Wrangellia and adjacent terranes to the south from the Yukon‐Tanana and adjacent terranes to the north. Geologic mapping suggests over 400 km of dextral slip has occurred on the fault, yet within the upper 1.5 km of the crust along the TACT corridor, basement rocks juxtaposed along the Denali fault reveal no significant seismic velocity differences, although the fault zone itself is associated with a minor lowering of velocity. The lack of seismic velocity contrast adjacent to the fault is in agreement with laboratory measurements of elastic wave velocities of samples from terranes bordering the fault. Laboratory measurements of elastic wave velocities of the metasedimentary mica‐quartz schists comprising the Yukon‐Tanana basement are highly anisotropic because of preferred orientation of mica and predict significant variations in velocity accompanying variations in foliation dip. Although other interpretations are possible, the northward shallowing of foliation dip of basement rocks in the Yukon‐Tanana terrane combined with the strong anisotropy associated with these highly foliated rocks can explain an observed northward increase in seismic velocity within this terrane. Seismic reflections from basement rocks within the Yukon‐Tanana terrane may originate from variations in anisotropy with depth and/or changes in composition reflecting different proportions of sandstone and shale in the protolith.

Alaska↗

USGS2012

Reflections from midcrustal rocks within the Mesozoic subduction complex near the eastern Aleutian Trench

Seismic reflection data collected in 1973 by Western Geophysical Company show that highly reflective rocks make up the midcrust of the convergent margin adjacent to the eastern Aleutian Trench. These rocks form an arch that strikes obliquely across the strongly expressed northeast-southwest structural grain of exposed Mesozoic rocks. In an earlier report we proposed that the deep events mark the location of either the presently subducting plate or the top of underplated rocks. However, the short radius of curvature of this arch precludes the possibility that the deep events indicate the igneous oceanic crust. Instead, the deep reflections could be from underplated rocks that have been arched by the imbrication or underplating of strata below the reflective rocks. High-amplitude water layer and interbed multiples prevent precise connection of shallow and deep geology. For example, the Border Ranges fault, a suture between major tectonostratigraphic terranes, is not revealed on any of our seismic sections. We speculate, however, that one band of reflections that rises toward but does not reach the surface is from the Eagle River thrust fault, which separates Late Cretaceous melange from deformed turbidite sequences of the same age.

Journal of Geophysical Research Solid Earth↗

USGS2011

Seismic survey probes urban earthquake hazards in Pacific Northwest

A multidisciplinary seismic survey earlier this year in the Pacific Northwest is expected to reveal much new information about the earthquake threat to U.S. and Canadian urban areas there. A disastrous earthquake is a very real possibility in the region. The survey, known as the Seismic Hazards Investigation in Puget Sound (SHIPS), engendered close cooperation among geologists, biologists, environmental groups, and government agencies. It also succeeded in striking a fine balance between the need to prepare for a great earthquake and the requirement to protect a coveted marine environment while operating a large airgun array.

Washington↗

USGS2009

A distal earthquake cluster concurrent with the 2006 explosive eruption of Augustine Volcano, Alaska

Clustered earthquakes located 25 km northeast of Augustine Volcano began about 6 months before and ceased soon after the volcano's 2006 explosive eruption. This distal seismicity formed a dense cluster less than 5 km across, in map view, and located in depth between 11 km and 16 km. This seismicity was contemporaneous with sharply increased shallow earthquake activity directly below the volcano's vent. Focal mechanisms for five events within the distal cluster show strike-slip fault movement. Cluster seismicity best defines a plane when it is projected onto a northeast–southwest cross section, suggesting that the seismogenic fault strikes northwest. However, two major structural trends intersect near Augustine Volcano, making it difficult to put the seismogenic fault into a regional-geologic context. Specifically, interpretation of marine multichannel seismic-reflection (MCS) data shows reverse faults, directly above the seismicity cluster, that trend northeast, parallel to the regional geologic strike but perpendicular to the fault suggested by the clustered seismicity. The seismogenic fault could be a reactivated basement structure.

Alaska↗

USGS2009

Potential earthquake faults offshore Southern California, from the eastern Santa Barbara Channel south to Dana Point

Urban areas in Southern California are at risk from major earthquakes, not only quakes generated by long-recognized onshore faults but also ones that occur along poorly understood offshore faults. We summarize recent research findings concerning these lesser known faults. Research by the U.S. Geological Survey during the past five years indicates that these faults from the eastern Santa Barbara Channel south to Dana Point pose a potential earthquake threat. Historical seismicity in this area indicates that, in general, offshore faults can unleash earthquakes having at least moderate (M 5-6) magnitude. Estimating the earthquake hazard in Southern California is complicated by strain partitioning and by inheritance of structures from early tectonic episodes. The three main episodes are Mesozoic through early Miocene subduction, early Miocene crustal extension coeval with rotation of the Western Transverse Ranges, and Pliocene and younger transpression related to plate-boundary motion along the San Andreas Fault. Additional complication in the analysis of earthquake hazards derives from the partitioning of tectonic strain into strike-slip and thrust components along separate but kinematically related faults. The eastern Santa Barbara Basin is deformed by large active reverse and thrust faults, and this area appears to be underlain regionally by the north-dipping Channel Islands thrust fault. These faults could produce moderate to strong earthquakes and destructive tsunamis. On the Malibu coast, earthquakes along offshore faults could have left-lateral-oblique focal mechanisms, and the Santa Monica Mountains thrust fault, which underlies the oblique faults, could give rise to large (M ??7) earthquakes. Offshore faults near Santa Monica Bay and the San Pedro shelf are likely to produce both strike-slip and thrust earthquakes along northwest-striking faults. In all areas, transverse structures, such as lateral ramps and tear faults, which crosscut the main faults, could segment earthquake rupture zones. ?? 2009 The Geological Society of America.

Special Paper of the Geological Society of America↗

USGS2007

Crustal structure of the Alaska Range orogen and Denali fault along the Richardson Highway

A suite of geophysical data obtained along the Richardson Highway crosses the eastern Alaska Range and Denali fault and reveals the crustal structure of the orogen. Strong seismic reflections from within the orogen north of the Denali fault dip as steeply as 25° north and extend downward to depths between 20 and 25 km. These reflections reveal what is probably a shear zone that transects most of the crust and is part of a crustal-scale duplex structure that probably formed during the Late Cretaceous. These structures, however, appear to be relict because over the past 20 years, they have produced little or no seismicity despite the nearby Mw = 7.9 Denali fault earthquake that struck in 2002. The Denali fault is nonreflective, but we interpret modeled magnetotelluric (MT), gravity, and magnetic data to propose that the fault dips steeply to vertically. Modeling of MT data shows that aftershocks of the 2002 Denali fault earthquake occurred above a rock body that has low electrical resistivity (>10 ohm-m), which might signify the presence of fluids in the middle and lower crust.

Special Paper of the Geological Society of America↗

USGS2006

Submarine landslides in the Santa Barbara Channel as potential tsunami sources

Recent investigations using the Monterey Bay Aquarium Research Institutes (MBARI) Remotely Operated Vehicles (ROVs) "Ventana" and "Tiburon" and interpretation of MBARI's EM 300 30 kHz multibeam bathymetric data show that the northern flank of the Santa Barbara Basin has experienced massive slope failures. Of particular concern is the large (130 km2) Goleta landslide complex located off Coal Oil Point near the town of Goleta, that measures 14.6-km long extending from a depth of 90 m to nearly 574 m deep and is 10.5 km wide. We estimate that approximately 1.75 km3 has been displaced by this slide during the Holocene. This feature is a complex compound submarine landslide that contains both surfical slump blocks and mud flows in three distinct segments. Each segment is composed of a distinct head scarp, down-dropped head block and a slide debris lobe. The debris lobes exhibit hummocky topography in the central areas that appear to result from compression during down slope movement. The toes of the western and eastern lobes are well defined in the multibeam image, whereas the toe of the central lobe is less distinct. Continuous seismic reflection profiles show that many buried slide debris lobes exist and comparison of the deformed reflectors with ODP Drill Site 149, Hole 893 suggest that at least 200 000 years of failure have occurred in the area (Fisher et al., 2005a). Based on our interpretation of the multibeam bathymetry and seismic reflection profiles we modeled the potential tsunami that may have been produced from one of the three surfical lobes of the Goleta slide. This model shows that a 10 m high wave could have run ashore along the cliffs of the Goleta shoreline. Several other smaller (2 km2 and 4 km2) slides are located on the northern flank of the Santa Barbara Basin, both to the west and east of Goleta slide and on the Concepcion fan along the western flank of the basin. One slide, named the Gaviota slide, is 3.8 km2, 2.6 km long and 1.7 km wide. A distinct narrow scar extends from near the eastern head wall of this slide for over 2 km eastward toward the Goleta slide and may represent either an incipient failure or a remnant of a previous failure. Push cores collected within the main head scar of this slide consisted of hydrogen sulfide bearing mud, possibly suggesting active fluid seepage and a vibra-core penetrated ???50 cm of recent sediment overlying colluvium or landslide debris confirming the age of ???300 years as proposed by Lee et al. (2004). However, no seeps or indications of recent movement were observed during our ROV investigation within this narrow head scar indicating that seafloor in the scar is draped with mud. ?? 2006 Author(s). This work is licensed under a Creative Commons License.

Natural Hazards and Earth System Sciences↗

USGS2005

Geology and tsunamigenic potential of submarine landslides in Santa Barbara Channel, Southern California

A large submarine landslide complex and four small landslides developed under the Santa Barbara Channel, suggesting a potential hazard from landslide-generated tsunamis. We integrate offshore stratigraphy and geologic structure, multibeam bathymetric information, and several kinds of seismic-reflection data to understand how and when the submarine landslides formed. Seismic-reflection data show that mass failure along the slope began at least 200 ka ago. Landslides appear as zones of poor reflectivity having an irregular upper surface, and these zones alternate vertically with strong parallel reflections. The emplacement ages of two of the three main landslide lobes are well established at 8 and 10 ka. The source material for the youngest part of the landslide complex was sediment of probable late Pleistocene and Holocene age that accumulated in a shelf-edge delta. Directly under this delta, growth of faults and anticlines was particularly intense and tended to oversteepen the deltaic deposits. These active structures also formed migration pathways and reservoirs for aqueous and hydrocarbon fluids from the deep basin. Tsunami deposits have been described from a low-lying area near Santa Barbara, and numerical modeling of tsunamis generated by hypothetical landslides in Santa Barbara Channel indicates a moderate to severe threat [Borrero, J.C., Dolan, J.F. and Synolakis, C.E., 2001. Tsunamis within the eastern Santa Barbara Channel. Geophys. Res. Lett., 28(4): 643-646.], involving wave runups of 2-20 m, for a range of assumed landslide volumes. Inundation from these waves, however, is expected to be highly focused so that only narrow (???10-km) sections of the shoreline would be affected. Crown Copyright ?? 2005 Published by Elsevier B.V. All rights reserved.

Marine Geology↗

USGS2005

Neotectonics of the offshore Oak Ridge fault near Ventura, southern California

The Oak Ridge fault is a large-offset, south-dipping reverse fault that forms the south boundary of the Ventura Basin in southern California. Previous research indicates that the Oak Ridge fault south of the town of Ventura has been inactive since 200-400 ka ago and that the fault tip is buried by ??? 1 km of Quaternary sediment. However, very high-resolution and medium-resolution seismic reflection data presented here show a south-dipping fault, on strike with the Oak Ridge fault, that is truncated at 80 m depth by an unconformity that is probably at the base of late Pleistocene and Holocene sediment. Furthermore, if vertically aligned features in seismic reflection data are eroded remnants of fault scarps, then a subsidiary fault within the Oak Ridge system deforms the shallowest imaged sediment layers. We propose that this subsidiary fault has mainly left-slip offset. These observations of Holocene slip on the Oak Ridge fault system suggest that revision of the earthquake hazard for the densely populated Santa Clara River valley and the Oxnard coastal plain may be needed.

Bulletin of the Seismological Society of America↗

USGS2004

The offshore Palos Verdes fault zone near San Pedro, Southern California

High-resolution seismic-reflection data are combined with a variety of other geophysical and geological data to interpret the offshore structure and earthquake hazards of the San Pedro shelf, near Los Angeles, California. Prominent structures investigated include the Wilmington graben, the Palos Verdes fault zone, various faults below the west part of the San Pedro shelf and slope, and the deep-water San Pedro basin. The structure of the Palos Verdes fault zone changes markedly along strike southeastward across the San Pedro shelf and slope. Under the north part of the shelf, this fault zone includes several strands, with the main strand dipping west. Under the slope, the main fault strands exhibit normal separation and mostly dip east. To the southeast near Lasuen Knoll, the Palos Verdes fault zone locally is low angle, but elsewhere near this knoll, the fault dips steeply. Fresh seafloor scarps near Lasuen Knoll indicate recent fault movement. We explain the observed structural variation along the Palos Verdes fault zone as the result of changes in strike and fault geometry along a master right-lateral strike-slip fault at depth. Complicated movement along this deep fault zone is suggested by the possible wave-cut terraces on Lasuen Knoll, which indicate subaerial exposure during the last sea level lowstand and subsequent subsidence of the knoll. Modeling of aeromagnetic data indicates a large magnetic body under the west part of the San Pedro shelf and upper slope. We interpret this body to be thick basalt of probable Miocene age. This basalt mass appears to have affected the pattern of rock deformation, perhaps because the basalt was more competent during deformation than the sedimentary rocks that encased the basalt. West of the Palos Verdes fault zone, other northwest-striking faults deform the outer shelf and slope. Evidence for recent movement along these faults is equivocal, because we lack age dates on deformed or offset sediment.

California↗

USGS2004

Geophysical data reveal the crustal structure of the Alaska range orogen within the aftershock zone of the Mw 7.9 Denali fault earthquake

Geophysical information, including deep-crustal seismic reflection, magnetotelluric ( mt ), gravity, and magnetic data, cross the aftershock zone of the 3 November 2002 M w 7.9 Denali fault earthquake. These data and aftershock seismicity, jointly interpreted, reveal the crustal structure of the right-lateral-slip Denali fault and the eastern Alaska Range orogen, as well as the relationship between this structure and seismicity. North of the Denali fault, strong seismic reflections from within the Alaska Range orogen show features that dip as steeply as 25° north and extend downward to depths between 20 and 25 km. These reflections reveal crustal structures, probably ductile shear zones, that most likely formed during the Late Cretaceous, but these structures appear to be inactive, having produced little seismicity during the past 20 years. Furthermore, seismic reflections mainly dip north, whereas alignments in aftershock hypocenters dip south. The Denali fault is nonreflective, but modeling of mt , gravity, and magnetic data suggests that the Denali fault dips steeply to vertically. However, in an alternative structural model, the Denali fault is defined by one of the reflection bands that dips to the north and flattens into the middle crust of the Alaska Range orogen. Modeling of mt data indicates a rock body, having low electrical resistivity (>10 Ω·m), that lies mainly at depths greater than 10 km, directly beneath aftershocks of the Denali fault earthquake. The maximum depth of aftershocks along the Denali fault is 10 km. This shallow depth may arise from a higher-than-normal geothermal gradient. Alternatively, the low electrical resistivity of deep rocks along the Denali fault may be associated with fluids that have weakened the lower crust and helped determine the depth extent of the aftershock zone.

Alaska↗

USGS2003

Geology of the continental margin beneath Santa Monica Bay, Southern California, from seismic-reflection data

We interpret seismic-reflection data, which were collected in Santa Monica Bay using a 70-in3 generator-injector air gun, to show the geologic structure of the continental shelf and slope and of the deep-water, Santa Monica and San Pedro Basins. The goal of this research is to investigate the earthquake hazard posed to urban areas by offshore faults. These data reveal that northwest of the Palos Verdes Peninsula, the Palos Verdes Fault neither offsets the seafloor nor cuts through an undeformed sediment apron that postdates the last sea level rise. Other evidence indicates that this fault extends northwest beneath the shelf in the deep subsurface. However, other major faults in the study area, such as the Dume and San Pedro Basin Faults, were active recently, as indicated by an arched seafloor and offset shallow sediment. Rocks under the lower continental slope are deformed to differing degrees on opposite sides of Santa Monica Canyon. Northwest of this canyon, the continental slope is underlain by a little-deformed sediment apron; the main structures that deform this apron are two lower-slope anticlines that extend toward Point Dume and are cored by faults showing reverse or thrust separation. Southeast of Santa Monica Canyon, lower-slope rocks are deformed by a complex arrangement of strike-slip, normal, and reverse faults. The San Pedro Escarpment rises abruptly along the southeast side of Santa Monica Canyon. Reverse faults and folds underpinning this escarpment steepen progressively southeastward. Locally they form flower structures and cut downward into basement rocks. These faults merge downward with the San Pedro Basin fault zone, which is nearly vertical and strike slip. The escarpment and its attendant structures diverge from this strike-slip fault zone and extend for 60 km along the margin, separating the continental shelf from the deep-water basins. The deep-water Santa Monica Basin has large extent but is filled with only a thin (less than 1.5-km) section of what are probably post-Miocene rocks and sediment. Extrapolating ages obtained from Ocean Drilling Program site 1015 indicates that this sedimentary cover is Quaternary, possibly no older than 600 ka. Folds and faults along the base of the San Pedro Escarpment began to form during 8-13 ka ago. Refraction-velocity data show that high-velocity rocks, probably the Catalina Schist or Miocene volcanic rocks, underlie the sedimentary section. The San Pedro Basin developed along a strike-slip fault, widens to the southeast, and is deformed by faults having apparent reverse separation and by folds near Redondo Canyon and the Palos Verdes Peninsula.

California↗

USGS2002

Subsurface geometry and evolution of the Seattle fault zone and the Seattle Basin, Washington

The Seattle fault, a large, seismically active, east-west-striking fault zone under Seattle, is the best-studied fault within the tectonically active Puget Lowland in western Washington, yet its subsurface geometry and evolution are not well constrained. We combine several analysis and modeling approaches to study the fault geometry and evolution, including depth-converted, deep-seismic-reflection images, P-wave-velocity field, gravity data, elastic modeling of shoreline uplift from a late Holocene earthquake, and kinematic fault restoration. We propose that the Seattle thrust or reverse fault is accompanied by a shallow, antithetic reverse fault that emerges south of the main fault. The wedge enclosed by the two faults is subject to an enhanced uplift, as indicated by the boxcar shape of the shoreline uplift from the last major earthquake on the fault zone. The Seattle Basin is interpreted as a flexural basin at the footwall of the Seattle fault zone. Basin stratigraphy and the regional tectonic history lead us to suggest that the Seattle fault zone initiated as a reverse fault during the middle Miocene, concurrently with changes in the regional stress field, to absorb some of the north-south shortening of the Cascadia forearc. Kingston Arch, 30 km north of the Seattle fault zone, is interpreted as a more recent disruption arising within the basin, probably due to the development of a blind reverse fault.

Washington↗

USGS2001

Upper crustal structure in Puget Lowland, Washington: Results from the 1998 Seismic Hazards Investigation in Puget Sound

A new three-dimensional (3-D) model shows seismic velocities beneath the Puget Lowland to a depth of 11 km. The model is based on a tomographic inversion of nearly one million first-arrival travel times recorded during the 1998 Seismic Hazards Investigation in Puget Sound (SHIPS), allowing higher-resolution mapping of subsurface structures than previously possible. The model allows us to refine the subsurface geometry of previously proposed faults (e.g., Seattle, Hood Canal, southern Whidbey Island, and Devils Mountain fault zones) as well as to identify structures (Tacoma, Lofall, and Sequim fault zones) that warrant additional study. The largest and most important of these newly identified structures lies along the northern boundary of the Tacoma basin; we informally refer to this structure here as the Tacoma fault zone. Although tomography cannot provide information on the recency of motion on any structure, Holocene earthquake activity on the Tacoma fault zone is suggested by seismicity along it and paleoseismic evidence for abrupt uplift of tidal marsh deposits to its north. The tomography reveals four large, west to northwest trending low-velocity basins (Tacoma, Seattle, Everett, and Port Townsend) separated by regions of higher velocity ridges that are coincident with fault-bounded uplifts of Eocene Crescent Formation basalt and pre-Tertiary basement. The shapes of the basins and uplifts are similar to those observed in gravity data; gravity anomalies calculated from the 3-D tomography model are in close agreement with the observed anomalies. In velocity cross sections the Tacoma and Seattle basins are asymmetric: the basin floor dips gently toward a steep boundary with the adjacent high-velocity uplift, locally with a velocity "overhang" that suggests a basin vergent thrust fault boundary. Crustal fault zones grow from minor folds into much larger structures along strike. Inferred structural relief across the Tacoma fault zone increases by several kilometers westward along the fault zone to Lynch Cove, where we interpret it as a zone of south vergent faulting overthrusting Tacoma basin. In contrast, structural relief along the Seattle fault zone decreases west of Seattle, which we interpret as evidence that the N-S directed compression is being accommodated by slip transfer between the Seattle and Tacoma fault zones. Together, the Tacoma and Seattle fault zones raise the Seattle uplift, one of a series of east-west trending, pop-up structures underlying Puget Lowland from the Black Hills to the San Juan Islands.

Washington↗

USGS2001

Imaging the Seattle Fault Zone with high-resolution seismic tomography

The Seattle fault, which trends east-west through the greater Seattle metropolitan area, is a thrust fault that, around 1100 years ago, produced a major earthquake believed to have had a magnitude greater than 7. We present the first high resolution image of the shallow P wave velocity variation across the fault zone obtained by tomographic inversion of first arrivals recorded on a seismic reflection profile shot through Puget Sound adjacent to Seattle. The velocity image shows that above 500 m depth the fault zone extending beneath Seattle comprises three distinct fault splays, the northernmost of which dips to the south at around 60??. The degree of uplift of Tertiary rocks within the fault zone suggests that the slip-rate along the northernmost splay during the Quaternary is 0.5 mm a-1, which is twice the average slip-rate of the Seattle fault over the last 40 Ma.

Geophysical Research Letters↗

USGS2001

Three-dimenstional crustal velocity structure beneath the Strait of Georgia, British Columbia

The Strait of Georgia is a topographic depression straddling the boundary between the Insular and Coast belts in southwestern British Columbia. Two shallow earthquakes located within the strait ( M = 4.6 in 1997 and M = 5.0 in 1975) and felt throughout the Vancouver area illustrate the seismic potential of this region. As part of the 1998 Seismic Hazards Investigation of Puget Sound (SHIPS) experiment, seismic instruments were placed in and around the Strait of Georgia to record shots from a marine source within the strait. We apply a tomographic inversion procedure to first-arrival traveltime data to derive a minimum-structure 3-D P -wave velocity model for the upper crust to about 13 km depth. We also present a 2-D velocity model for a profile orientated across the Strait of Georgia derived using a minimum-parameter traveltime inversion approach. This paper represents the first detailed look at crustal velocity variations within the major Cretaceous to Cenozoic Georgia Basin, which underlies the Strait of Georgia. The 3-D velocity model clearly delineates the structure of the Georgia Basin. Taking the 6 km s −1 isovelocity contour to represent the top of the underlying basement, the basin thickens from between 2 and 4 km in the northwestern half of the strait to between 8 and 9 km at the southeastern end of the study region. Basin velocities in the northeastern half are 4.5–6 km s −1 and primarily represent the Upper Cretaceous Nanaimo Group. Velocities to the south are lower (3–6 km s −1 ) because of the additional presence of the overlying Tertiary Huntingdon Formation and more recent sediments, including glacial and modern Fraser River deposits. In contrast to the relatively smoothly varying velocity structure of the basin, velocities of the basement rocks, which comprise primarily Palaeozoic to Jurassic rocks of the Wrangellia Terrane and possibly Jurassic to mid-Cretaceous granitic rocks of the Coast Belt, show significantly more structure, probably an indication of the varying basement rock lithologies. The 2-D velocity model more clearly reveals the velocity layering associated with the recent sediments, Huntingdon Formation and Nanaimo Group of the southern Georgia Basin, as well as the underlying basement. We interpret lateral variation in sub-basin velocities of the 2-D model as a transition from Wrangellian to Coast Belt basement rocks. The effect of the narrow, onshore–offshore recording geometry of the seismic experiment on model resolution was tested to allow a critical assessment of the validity of the 3-D velocity model. Lateral resolution throughout the model to a depth of 3–5 km below the top of the basement is generally 10–20 km.

British Columbia↗

USGS1999

Three-dimensional velocity structure of Siletzia and other accreted terranes in the Cascadia forearc of Washington

Eocene mafic crust with high seismic velocities underlies much of the Oregon and Washington forearc and acts as a backstop for accretion of marine sedimentary rocks from the obliquely subducting Juan de Fuca slab. Arc-parallel migration of relatively strong blocks of this terrane, known as Siletzia, focuses upper crustal deformation along block boundaries, which are potential sources of earthquakes. In a three-dimensional velocity model of coastal Washington, we have combined surface geology, well data, and travel times from earthquakes and controlled source seismic experiments to resolve the major boundaries of the Siletz terrane with the adjacent accreted sedimentary prism and volcanic arc. In southern Washington and northern Oregon the Siletz terrane appears to be a thick block (???20 km) that extends west of the coastline and makes a high-angle contact with the offshore accreted sedimentary prism. On its east flank the high-velocity Siletz terrane boundary coincides with an en echelon zone of seismicity in the arc. In northern Washington the western edge of Siletzia makes a lower-angled, fault-bound contact with the accretionary prism. In addition, alternating, east-west trending uplifts and downwarps of the Siletz terrane centered on the antiformal Olympic Mountains may reflect focusing of north-south compression in the northern part of the Siletz terrane. This compressional strain may result from northward transport and clockwise rotation of the Siletz terrane into the relatively fixed Canadian Coast Mountains restraining bend along the coast.

Oregon, Washington↗