Geology ReportsSearch

Geology topics

John R. Van Schaack

Publications and source records attributed to John R. Van Schaack.

4 recordsLinked to original sources

Report for borehole explosion data acquired in the 1999 Los Angeles Region Seismic Experiment (LARSE II), Southern California: Part I, description of the survey

The Los Angeles Region Seismic Experiment (LARSE) is a joint project of the U.S. Geological Survey (USGS) and the Southern California Earthquake Center (SCEC). The purpose of this project is to produce seismic images of the subsurface of the Los Angeles region down to the depths at which earthquakes occur, and deeper, in order to remedy a deficit in our knowledge of the deep structure of this region. This deficit in knowledge has persisted despite over a century of oil exploration and nearly 70 years of recording earthquakes in southern California. Understanding the deep crustal structure and tectonics of southern California is important to earthquake hazard assessment. Specific imaging targets of LARSE include (a) faults, especially blind thrust faults, which cannot be reliably detected any other way; and (b) the depths and configurations of sedimentary basins. Imaging of faults is important in both earthquake hazard assessment but also in modeling earthquake occurrence. Earthquake occurrence cannot be understood unless the earthquake-producing "machinery" (tectonics) is known (Fuis and others, 2001). Imaging the depths and configurations of sedimentary basins is important because earthquake shaking at the surface is enhanced by basin depth and by the presence of sharp basin edges (Wald and Graves, 1998, Working Group on California Earthquake Probabilities, 1995; Field and others, 2001). (Sedimentary basins are large former valleys now filled with sediment eroded from nearby mountains.) Sedimentary basins in the Los Angeles region that have been investigated by LARSE include the Los Angeles, San Gabriel Valley, San Fernando Valley, and Santa Clarita Valley basins. The seismic imaging surveys of LARSE include recording of earthquakes (both local and distant earthquakes) along several corridors (or transects) through the Los Angeles region and also recording of man-made sources along these same corridors. Man-made sources have included airguns offshore and borehole explosions and vibrating-truck sources onshore. The two chief LARSE transects pass near recent moderate earthquakes, including the 1971 M 6.7 San Fernando, 1987 M 5.9 Whittier Narrows, 1991 M 5.8 Sierra Madre, and 1994 M 6.7 Northridge earthquakes. The first transect extended from San Clemente Island northeastward to the Mojave Desert (Line 1, Fig. 1), passing near the epicenter of the Whittier Narrows and Sierra Madre earthquakes. The second transect extended from west of San Clemente Island northward to the western Mojave Desert (Line 2, Figs. 1, 2), passing through the epicenter of the Northridge earthquake and near the epicenter of the San Fernando earthquake. Data along Line 1 were acquired during the years 1993-1994, and data along Line 2, during the years 1994–2000. In this open-file report and that of Murphy and others (in preparation), we present the details of the October 1999 explosion survey along Line 2, which extended from Santa Monica Bay northward to the western Mojave Desert (Figs. 1, 2). This survey is referred to as LARSE II. In this survey, 93 borehole explosions were detonated along the main north-south line and along 5 auxiliary lines in the San Fernando Valley and Santa Monica areas. These explosions were recorded by ~1400 seismographs. A variety of seismic instrumentation was used in these imaging surveys and was obtained from collaborators from around the world, including the Geological Survey of Canada (Ottawa, Canada), IRIS/PASSCAL (Socorro, NM), Lamont-Doherty Earth Observatory (Palisades, NY), Stanford University (Stanford, CA), SCEC (Los Angeles, CA), USGS (Menlo Park, CA, and Woods Hole, MA), University of Texas at El Paso (El Paso, TX), GeoForschungsZentrum (Potsdam, Germany), University of Karlsruhe (Karlsruhe, Germany), and University of Copenhagen (Copenhagen, Denmark). The reader is referred to Table 1 for instrumentation used in LARSE II.

California

Factors limiting the sensitivity and dynamic range of a seismic system employing analog magnetic tape recording and a seismic amplifier with adjustable gain settings and several output levels

In the course of modernizing the low-speed-tape-recorder portable seismic systems and considering the possibilities for the design of a cassette-tape-recorder seismic refraction system, the factors that limit the sensitivity and dynamic range of such systems have been reviewed. These factors will first be stated briefly, and then their influence on systems such as the new 5-day-tape seismic system will be examined in more detail. To fix ideas, we shall assume that the system consists of the following elements: 1. A seismic sensor: usually a moving coil inertial seismometer with a period of about 1 second, a coil resistance of about 5000 ohms, and an effective motor constant of 1.0 V/cm/sec (across a 10K load terminating the seismometer sensitivity-and-damping-adjustment resistive network). 2. A seismic amplifier/voltage controlled oscillator unit made up of the following components: a) A fixed gain preamplifier with an input resistance of 10K and an internal noise level of 0.5 muVpp referred to the preamp input (0.1 Hz <= freq. <= 30 hz). b) An adjustable gain (0 to 42 db in 6 db steps) intermediate amplifier c) One or more fixed gain output amplifiers. d) Two sections of 6 db/octave bandpass filter serving to couple the 3 amplifier stages together. e) Voltage controlled oscillators for each output amplifier to produce modulated FM carriers for recording on separate tape tracks or modulated FM subcarriers for subsequent multiplexing and direct recording on tape in the California Network format. 3. An analog magnetic tape recorder: e.g. the PI 5100 (15/80 ips recording in the FM mode or in the direct mode with the 'broad-band' variant-of the Cal Net multiplex system, or 15/16 ips recording in the direct mode with the standard Cal Net multiplex system), or the Sony TC-126 cassette recorder operating in the direct record mode with the standard Cal Net multiplex system. 4. Appropriate magnetic tape playback equipment: e.g., the Bell and Howell 3700-B for the PI-5100 or the Sony TC 126 for its own tapes. 5. Appropriate discriminators (employing subtractive compensation, at least for the multiplexed systems) to restore the data signals to their original forms. 6. An A/D convertor to digitize the seismic signals for computer processing and/or a strip chart recorder (e.g., the Siemens Oscillomink) for playout of the data.

Open-File Report