Jing-Jiang Yu | Geology Reports

USGS2020

Investigating the effects of broad ion beam milling to sedimentary organic matter: Surface flattening or heat-induced aromatization and condensation?

Previous work has proposed transfer of kinetic heat energy from low-energy broad ion beam (BIB) milling causes thermal alteration of sedimentary organic matter, resulting in increases of organic matter reflectance. Whereas, other studies have suggested the organic matter reflectance increase from BIB milling is due to decreased surface roughness. To test if reflectance increases to sedimentary organic matter (vitrinite) caused by BIB milling were related to molecular aromatization and condensation, Raman and Fourier transform infrared (FTIR) spectroscopies were used to evaluate potential compositional changes in the same vitrinite locations pre- and post-BIB milling. The same locations also were examined by atomic force microscopy (AFM) to determine topographic changes caused by BIB milling (as quantified by the areal root-mean-square roughness parameter S q ). Samples consisted of four medium volatile bituminous coals. A non-aggressive BIB milling approach was used with conditions of 5 min, 4 keV, 15°incline, 360° rotation at 25 rpm and 100% focus (1.5 kV discharge; ∼100 μA). This gentle BIB milling caused vitrinite reflectance (VR o ) increases of 12 to 36% of the original values determined optically before milling (average 26% increase). When molecular proxies from FTIR (A- and C-factor, branching ratio) were plotted against each other for the same vitrinite locations pre- and post-milling, mean data points for each sample generally lie within error of a 1:1 line. Likewise, mean Raman thermal proxy [full-width half maximum of G-band (G-FWHM), Raman band separation (RBS) and D1/G band intensity ratio] values were similar for pre- and post-milled locations, also plotting within error of a 1:1 line. AFM confirms the majority (24 of 36) of pre- and post-ion milled surface pairs were smoother (lower S q values) after BIB milling. These results are interpreted to indicate VR o increase induced by the gentle BIB milling conditions used in this study is an effect of decreased diffuse reflectance due to flatter surfaces, causing more photons to reflect directly back to the detector. Little evidence was observed for molecular aromatization and condensation of vitrinite molecules following BIB milling (with the conditions used). The presence of milling-induced artifacts, including differential milling effects dependent on location and the development of self-organized patterned structures, indicate much work remains in standardization of BIB milling before its promulgation as a routine sample preparation technique for organic petrography. These results provide better understanding of anthropogenic-induced changes to geological samples caused by the now widespread adoption of BIB milling as a disruptive innovation in sample preparation.

Fuel↗

USGS2019

Reflectance increase from broad beam ion milling of coals and organic-rich shales due to increased surface flatness

Broad ion beam (BIB) milling is useful in organic petrology because it can yield flat sample surfaces and avert the ‘smearing’ of organic matter (OM) that results from traditional mechanical polishing. This potentially makes BIB especially useful in the study of nano-porosity, where even minor mechanical disruption of the sample surface distorts the sample characteristic of interest—the pore structure. However, several studies have observed an OM reflectance increase after BIB milling, concluding that ion milling may cause thermal alteration to OM surfaces. To better understand ion milling effects on organic matter, coal (subbituminous, high volatile bituminous, medium volatile bituminous, anthracite) and shale [Bakken Formation, Ohio Shale-Huron Member (5), Kimmeridge Clay Formation, Alum Shale, New Albany Shale] samples were prepared using traditional mechanical polishing methods. Reflectance measurements (% Ro) were gathered on all maceral types present before BIB milling, followed by re-measurement of OM reflectance at the same locations after milling. Most OM increased in reflectance after BIB milling, with some exceptions in high maturity samples. Liptinite macerals in both coal and shale samples showed the greatest percent reflectance increase on average (+133%; n=338), followed by solid bitumen (+49%; n=313), vitrinite (+26%; n=413), and inertinite (+9%; n=220). Despite the increases to OM reflectance caused by BIB milling, no evidence was found for kerogen conversion (e.g., change in maceral abundances), or for migration of newly generated petroleum (e.g., pseudomorphic replacement of kerogen by solid bitumen). Such changes occur when samples are thermally altered from immature conditions into the oil window (e.g., by hydrous pyrolysis), and, if the increases in OM reflectance were thermally driven (by BIB milling), they should have been observed in the above experiments. Herein, we also used atomic force microscopy to document a decrease in surface roughness of correlative locations of OM on pre- and post-ion milled samples. This improved surface polish caused by BIB milling appears to be the root cause of increased OM reflectance, as no other supporting evidence of thermal alteration could be found. That is, the fraction of light formerly lost to oblique scatter in diffuse reflectance from a mechanically polished surface is converted to specular reflectance after BIB ion milling. Thus the light leaves the surface at a near normal angle and returns to the detector, resulting in increased OM reflectance.

International Journal of Coal Geology↗