Surrogate technologies for monitoring suspended-sediment transport in rivers
No abstract available.
Book chapter↗
Geology topics
Jeffrey W. Gartner
Publications and source records attributed to Jeffrey W. Gartner.
Surrogate technologies for monitoring bed-load transport in rivers
No abstract available.
Book chapter↗
Use of acoustic backscatter and vertical velocity to estimate concentration and dynamics of suspended solids in Upper Klamath Lake, south-central Oregon: Implications for Aphanizomenon flos-aquae
Vertical velocity and acoustic backscatter measurements by acoustic Doppler current profilers were used to determine seasonal, subseasonal (days to weeks), and diel variation in suspended solids in a freshwater lake where massive cyanobacterial blooms occur annually. During the growing season, the suspended material in the lake is dominated by the buoyancy-regulating cyanobacteria, Aphanizomenon flos-aquae . Measured variables (water velocity, relative backscatter [ RB ], wind speed, and air and water temperatures) were averaged over the deployment season at each sample time of day to determine average diel cycles. Phase shifts between diel cycles in RB and diel cycles in wind speed, vertical water temperature differences (Δ T° ), and horizontal current speeds were found by determining the lead or lag that maximized the linear correlation between the respective diel cycles. Diel cycles in RB were more in phase with Δ T° cycles, and, to a lesser extent, wind cycles, than to water current cycles but were out of phase with the cycle that would be expected if the vertical movement of buoyant cyanobacteria colonies was controlled primarily by light. Clear evidence of a diel cycle in vertical velocity was found only at the two deepest sites in the lake. Cycles of vertical velocity, where present, were out of phase with expected vertical motion of cyanobacterial colonies based on the theoretical cycle for light-driven vertical movement. This suggests that water column stability and turbulence were more important factors in controlling vertical distribution of colonies than light. Variations at subseasonal time scales were determined by filtering data to pass periods between 1.2 and 15 days. At subseasonal time scales, correlations between RB and currents or air temperature were consistent with increased concentration of cyanobacterial colonies near the surface when water column stability increased (higher air temperatures or weaker currents) and dispersal of colonies throughout the water column when the water column mixed more easily. RB was used to estimate suspended solids concentrations (SSC). Correlations of depth-integrated SSC with currents or air temperatures suggest that depth-integrated water column mass decreased under conditions of greater water column stability and weaker currents. Results suggest that the use of measured vertical velocity and acoustic backscatter as a surrogate for suspended material has the potential to contribute significant additional insight into dynamics of Aphanizomenon flos-aquae colonies in Upper Klamath Lake, south-central Oregon.
Oregon↗
Overview of selected surrogate technologies for high-temporal resolution suspended-sediment monitoring
Traditional methods for characterizing selected properties of suspended sediments in rivers are being augmented and in some cases replaced by cost-effective surrogate instruments and methods that produce a temporally dense time series of quantifiably accurate data for use primarily in sediment-flux computations. Turbidity is the most common such surrogate technology, and the first to be sanctioned by the U.S. Geological Survey for use in producing data used in concert with water-discharge data to compute sediment concentrations and fluxes for storage in the National Water Information System. Other technologies, including laser-diffraction, digital photo-optic, acoustic-attenuation and backscatter, and pressure-difference techniques are being evaluated for producing reliable sediment concentration and, in some cases, particle-size distribution data. Each technology addresses a niche for sediment monitoring. Their performances range from compelling to disappointing. Some of these technologies have the potential to revolutionize fluvial-sediment data collection, analysis, and availability.
Conference Paper↗
Technological advances in suspended‐sediment surrogate monitoring
Surrogate technologies to continuously monitor suspended sediment show promise toward supplanting traditional data collection methods requiring routine collection and analysis of water samples. Commercially available instruments operating on bulk optic (turbidity), laser optic, pressure difference, and acoustic backscatter principles are evaluated based on cost, reliability, robustness, accuracy, sample volume, susceptibility to biological fouling, and suitable range of mass concentration and particle size distribution. In situ turbidimeters are widely used. They provide reliable data where the point measurements can be reliably correlated to the river's mean cross section concentration value, effects of biological fouling can be minimized, and concentrations remain below the sensor's upper measurement limit. In situ laser diffraction instruments have similar limitations and can cost 6 times the approximate $5000 purchase price of a turbidimeter. However, laser diffraction instruments provide volumetric‐concentration data in 32 size classes. Pressure differential instruments measure mass density in a water column, thus integrating substantially more streamflow than a point measurement. They are designed for monitoring medium‐to‐large concentrations, are generally unaffected by biological fouling, and cost about the same as a turbidimeter. However, their performance has been marginal in field applications. Acoustic Doppler profilers use acoustic backscatter to measure suspended sediment concentrations in orders of magnitude more streamflow than do instruments that rely on point measurements. The technology is relatively robust and generally immune to effects of biological fouling. Cost of a single‐frequency device is about double that of a turbidimeter. Multifrequency arrays also provide the potential to resolve concentrations by clay silt versus sand size fractions. Multifrequency hydroacoustics shows the most promise for revolutionizing collection of continuous suspended sediment data by instruments that require only periodic calibration for correlation to mean concentrations in river cross sections. Broad application of proven suspended sediment surrogate technologies has the potential to revolutionize fluvial sediment monitoring. Once applied, benefits could be enormous, providing for safer, more frequent and consistent, arguably more accurate, and ultimately less expensive sediment data for managing the world's sedimentary resources.
Water Resources Research↗
Modeling hydrodynamics and heat transport in Upper Klamath Lake, Oregon, and implications for water quality
The three-dimensional numerical model UnTRIM was used to model hydrodynamics and heat transport in Upper Klamath Lake, Oregon, between mid-June and mid-September in 2005 and between mid-May and mid-October in 2006. Data from as many as six meteorological stations were used to generate a spatially interpolated wind field to use as a forcing function. Solar radiation, air temperature, and relative humidity data all were available at one or more sites. In general, because the available data for all inflows and outflows did not adequately close the water budget as calculated from lake elevation and stage-capacity information, a residual inflow or outflow was used to assure closure of the water budget. Data used for calibration in 2005 included lake elevation at 3 water-level gages around the lake, water currents at 5 Acoustic Doppler Current Profiler (ADCP) sites, and temperature at 16 water-quality monitoring locations. The calibrated model accurately simulated the fluctuations of the surface of the lake caused by daily wind patterns. The use of a spatially variable surface wind interpolated from two sites on the lake and four sites on the shoreline generally resulted in more accurate simulation of the currents than the use of a spatially invariant surface wind as observed at only one site on the lake. The simulation of currents was most accurate at the deepest site (ADCP1, where the velocities were highest) using a spatially variable surface wind; the mean error (ME) and root mean square error (RMSE) for the depth-averaged speed over a 37-day simulation from July 26 to August 31, 2005, were 0.50 centimeter per second (cm/s) and 3.08 cm/s, respectively. Simulated currents at the remaining sites were less accurate and, in general, underestimated the measured currents. The maximum errors in simulated currents were at a site near the southern end of the trench at the mouth of Howard Bay (ADCP7), where the ME and RMSE in the depth-averaged speed were 3.02 and 4.38 cm/s, respectively. The range in ME of the temperature simulations over the same period was –0.94 to 0.73 degrees Celsius (°C), and the RMSE ranged from 0.43 to 1.12°C. The model adequately simulated periods of stratification in the deep trench when complete mixing did not occur for several days at a time. The model was validated using boundary conditions and forcing functions from 2006 without changing any calibration parameters. A spatially variable wind was used. Data for the model validation periods in 2006 included lake elevation at 4 gages around the lake, currents collected at 2 ADCP sites, and temperature collected at 21 water-quality monitoring locations. Errors generally were larger than in 2005. ME and RMSE in the simulated velocity at ADCP1 were 2.30 cm/s and 3.88 cm/s, respectively, for the same 37-day simulation over which errors were computed for 2005. The ME in temperature over the same period ranged from –0.56 to 1.5°C and the RMSE ranged from 0.41 to 1.86°C. Numerical experiments with conservative tracers were used to demonstrate the prevailing clockwise circulation patterns in the lake, and to show the influence of water from the deep trench located along the western shoreline of the lake on fish habitat in the northern part of the lake. Because water exiting the trench is split into two pathways, the numerical experiments indicate that bottom water from the trench has a stronger influence on water quality in the northern part of the lake, and surface water from the trench has a stronger influence on the southern part of the lake. This may be part of the explanation for why episodes of low dissolved oxygen tend to be more severe in the northern than in the southern part of the lake.
Oregon↗
Water velocity and suspended solids measurements by in-situ instruments in Upper Klamath Lake, Oregon
The U. S. Geological Survey conducted hydrodynamic measurements in Upper Klamath Lake during four summer seasons (approximately mid-June to mid-September) during 2003 to 2006. Measurements included water current profiles made by acoustic Doppler current profilers at a number of fixed locations in the lake during all four years as well as from a moving boat during 2005 and 2006. Measurements of size distribution of suspended material were made at four locations in the lake during 2004-2006. Raw (unfiltered) data are presented as time series of measurements. In addition, water-velocity data have been filtered to remove wind-induced variations with periods less than thirty hours from the measurements. Bar graphs of horizontal and vertical water speed and acoustic backscatter have been generated to discern diurnal variations, especially as they relate to wind patterns over the lake. Mean speeds of the horizontal currents in the lake range between about 3.5 to 15 cm/s with the higher speeds at the deep locations in the trench on the west side of the lake. Current directions generally conform to the lake’s bathymetry contours and the water circulation pattern is usually in a clockwise direction around the lake as established by the prevailing north to northwesterly surface winds in the region. Diurnal patterns in horizontal currents probably relate to diurnal wind patterns with minimum wind speeds near noon and maximum wind speeds near 2100. Diurnal variations in vertical velocities do not appear to be related to wind patterns; they do appear to be related to expected patterns of vertical migration of Aphanizomenon flos aquae , (AFA) the predominant species of blue-green algae in the lake. Similarly, diurnal variations in acoustic backscatter, especially near the lake’s surface, are probably related to the vertical migration of AFA.
Oregon↗
Evaluating a Radar-Based, Non Contact Streamflow Measurement System in the San Joaquin River at Vernalis, California
Accurate measurement of flow in the San Joaquin River at Vernalis, California, is vital to a wide range of Federal and State agencies, environmental interests, and water contractors. The U.S. Geological Survey uses a conventional stage-discharge rating technique to determine flows at Vernalis. Since the flood of January 1997, the channel has scoured and filled as much as 20 feet in some sections near the measurement site resulting in an unstable stage-discharge rating. In response to recent advances in measurement techniques and the need for more accurate measurement methods, the Geological Survey has undertaken a technology demonstration project to develop and deploy a radar-based streamflow measuring system on the bank of the San Joaquin River at Vernalis, California. The proposed flow-measurement system consists of a ground-penetrating radar system for mapping channel geometries, a microwave radar system for measuring surface velocities, and other necessary infrastructure. Cross-section information derived from ground penetrating radar provided depths similar to those measured by other instruments during the study. Likewise, surface-velocity patterns and magnitudes measured by the pulsed Doppler radar system are consistent with near surface current measurements derived from acoustic velocity instruments. Since the ratio of surface velocity to mean velocity falls to within a small range of theoretical value, using surface velocity as an index velocity to compute river discharge is feasable. Ultimately, the non-contact radar system may be used to make continuous, near-real-time flow measurements during high and medium flows. This report documents the data collected between April 14, 2002 and May 17, 2002 for the purposes of testing this radar based system. Further analyses of the data collected during this field effort will lead to further development and improvement of the system.
Open-File Report↗
Surrogate technologies for continuous suspended-sediment monitoring in the United States
No abstract available.
Conference Paper↗
Laboratory and field evaluations of the LISST-100 instrument for suspended particle size determinations
Advances in technology have resulted in a new instrument that is designed for in-situ determination of particle size spectra. Such an instrument that can measure undisturbed particle size distributions is much needed for sediment transport studies. The LISST-100 (Laser In-Situ Scattering and Transmissometry) uses the principle of laser diffraction to obtain the size distribution and volume concentration of suspended material in 32 size classes logarithmically spaced between 1.25 and 250 μm. This paper describes a laboratory evaluation of the ability of LISST-100 to determine particle sizes using suspensions of single size, artificial particles. Findings show the instrument is able to determine particle size to within about 10% with increasing error as particle size increases. The instrument determines volume (or mass) concentration using a volume conversion factor C v . This volume conversion factor is theoretically a constant. In the laboratory evaluation C v is found to vary by a factor of about three over the particle size range between 5 and 200 μm. Results from field studies in South San Francisco Bay show that values of mass concentration of suspended marine sediments estimated by LISST-100 agree favorably with estimates from optical backscatterance sensors if an appropriate value of C v , according to mean size, is used and the assumed average particle (aggregate) density is carefully chosen. Analyses of size distribution of suspended materials in South San Francisco Bay over multiple tide cycles suggest the likelihood of different sources of sediment because of different size characteristics during flood and ebb cycles.
Marine Geology↗
Bottom boundary layer in south San Francisco Bay, California
Detailed velocity distributions within the benthic turbulent boundary layer were measured by a Broad Band Acoustic Doppler Current Profiler (BB-ADCP) in South San Francisco Bay, California. In "mode 5", the BB-ADCP was able to measure velocity in 5 cm increments. The validation of these measurements was achieved by comparing the BB-ADCP measurements with the velocities measured by a Narrow Band Acoustic Doppler Current Profiler (NB-ADCP) in close proximity. There were thirty-three (33) velocity time-series measured by the BB-ADCP beginning at 7 cm above bed and extending to 175 cm in water column for about two weeks. The velocities from locations at 7 cm and 12 cm above the bed were determined to be of lower accuracy, and they were not used in estimates of friction velocity, u.. The values of u. at 95% confidence level were determined with relative error less than 20%. The time-series of u. varied with velocity outside of the boundary layer, and responded to spring-neap tidal variations. Attempts to use acoustic backscatterance echo intensity to measure suspended sediment concentration showed prom ise, and merit consideration in future studies.
California↗
Near bottom velocity measurements in San Francisco Bay, California
The ability to accurately measure long-term time-series of tidal currents in bays and estuaries is critical in estuarine hydrodynamic studies. Accurate measurements of tidal currents near the air-water interface and in the bottom boundary layer remain difficult in spite of the significant advances in technology for measuring tidal currents which have been achieved in recent years. One of the objectives of this study is to demonstrate that turbulent mean velocity distribution within the bottom boundary layer can be determined accurately by using a broad-band acoustic Doppler current profiler (BB-ADCP). A suite of instruments, including two BB-ADCPs and four electromagnetic (EM) current meters was deployed in San Francisco Bay, California in an investigation of resuspension and transport of sediment during March 1995. The velocity measurements obtained in the bottom boundary layer by BB-ADCP were highly coherent (r2>0.94) with the velocity measurements obtained by EM current meters. During early March 1995, both BB-ADCPs and EM current meters recorded a very unusual flow event. Agreement among independent measurements by these instruments in describing such an atypical hydrodynamic occurrence further validates the velocity measurements obtained by BB-ADCP in the bottom boundary layer.
Conference Paper↗