Geology topics

Jeffrey D. Pepin

Publications and source records attributed to Jeffrey D. Pepin.

14 recordsLinked to original sources

USGS2026

Geothermal district energy systems coupled with seasonal underground thermal energy storage: A U.S. techno-economic screening by climate and geology

In the United States, cooling-dominated commercial building loads can cause geothermal heat pump-based district energy systems to accumulate a long-term subsurface thermal imbalance, motivating the incorporation of seasonal underground thermal energy storage. We developed a transferable workflow to evaluate geothermal district systems that pair ground heat exchangers with seasonal underground thermal energy storage. Using standardized hourly loads for seven commercial buildings and a uniform cost framework, we simulated ten U.S. cities with a physics-based ground heat exchanger model, subsurface storage simulations, and economic assessment to isolate the roles of climate and hydrogeology. In cooling-dominated cities, underground thermal energy storage supplied the majority of annual cooling, cutting electricity use and summer peaks substantially while achieving levelized costs comparable to or below conventional chiller-boiler plants. In cooler climates, the storage share shrunk, required borefield size and costs rose, and levelized cost of energy increased nearly linearly with declining underground thermal energy storage fraction, indicating storage fraction as the primary economic lever. Sensitivity analysis showed capital risk dominated by borefield drilling and surface heating, ventilation, and air-conditioning and piping, with underground thermal energy storage costs secondary. This workflow provides a transparent foundation for site-specific design and screening of next-generation geothermal district energy systems.

Arizona, Illinois, Maryland, Michigan, Mississippi↗

USGS2026

Assessment of undiscovered oil and gas resources in the Bossier Formation within the onshore United States and State waters of the Gulf Coast Region, 2025

Using a geology-based assessment methodology, the U.S. Geological Survey estimated undiscovered, technically recoverable mean resources of 3 million barrels of oil and 343.5 trillion cubic feet of gas in reservoirs of the Bossier Formation within the onshore United States and State waters of the Gulf Coast region.

Alabama, Arkansas, Florida, Louisiana, Mississippi↗

USGS2026

Prioritizing resource protection and understanding potential susceptibility of springs to surficial changes in a low-temperature geothermal system

Geothermal systems are vulnerable to changes in water budget and composition, requiring science-based management. This study uses a dataset of spring water temperatures, time series of groundwater residence time tracers (tritium and carbon-14), and stable isotopes of water to understand geothermal flow in a low-temperature geothermal system in north west Colorado, United States (Steamboat Springs). The geothermal system is bisected by the Yampa River, necessitating a stream mass balance approach to quantify total discharge. Time series analysis of water temperature data provides a ranked list of features more susceptible to surficial changes, which is corroborated using time series of tritium which indicate spatially distinct patterns of mixing between modern and pre-modern groundwater. All springs contain a portion of pre-modern groundwater that is thousands to tens of thousands of years old, a period coinciding with melting of extensive Pleistocene glaciers that was likely one of the recharge sources to the geothermal system. Stream mass balance indicates that greater than 80% of the total geothermal discharge is derived from diffuse or small springs, highlighting the extensive nature of the geothermal outflow zone and the association with local geologic structures. This study provides baseline data to support management of the Steamboat Springs geothermal system and indicates the utility of these approaches in developing science-based geothermal management.

Colorado↗

USGS2025

Sources of water and salts for the Zuni Salt Lake in west-central New Mexico

The Zuni Salt Lake is located in a maar in west-central New Mexico and contains hypersaline water that has long been used by Native Americans for religious purposes and the collection of salt. There have been several investigations suggesting different sources for the water and salt to the lake. Springs, seeps, and ephemeral streamflow have all been observed to contribute freshwater to the lake, and brackish to hypersaline seeps have been documented along the banks of the lake. This report summarizes the findings of a study that characterizes the lake’s hydrology, its water and salinity sources, and the hydrogeologic conceptual model. Regional groundwater levels indicate that each of the aquifers in the area have the potential to discharge groundwater to the lake. There is also evidence of vertical groundwater flow pathways at the maar that were likely created by the igneous intrusion that fractured the intersecting aquifers. A detailed water budget was constructed from continuous lake stage, precipitation, and evaporation data to estimate the groundwater inflow to the Zuni Salt Lake. It was determined that groundwater inflow to the lake is 441 ±94 acre-feet per year, which composes as much as 77 percent of the total inflows. The high sodium and chloride concentrations measured in two hypersaline samples collected near the lake indicate that the majority of the dissolved solids entering the lake are from a hypersaline groundwater source. The geochemical and isotopic compositions measured in the lake and surrounding features support the interpretation that hypersaline groundwater is the primary source of salts to the lake, which is likely sourced from the older (and deeper) Permian units. The hypersaline groundwater samples collected during this investigation have a unique aqueous chemistry relative to each of the mapped aquifers, and variability in groundwater compositions is interpreted to result from differences in minerology and residence time.

New Mexico↗

USGS2025

Reservoir thermal energy storage pre-assessment for the United States

Storing thermal energy underground for later use in electricity production or direct-use heating/cooling is a promising, viable, and economical green energy option. Reservoir thermal energy storage (RTES) is one such option, which stores energy in underutilized permeable strata with low ambient groundwater flow rates and more geochemically evolved (e.g. brackish/saline) waters relative to overlying principal aquifer systems. The U.S. Geological Survey has begun assessing RTES potential nationally by focusing on five generalized geologic regions (Basin and Range, Coastal Plain, Illinois Basin, Michigan Basin, Pacific Northwest) across the United States. Hydrogeologic reservoir models are developed for the following eight metropolitan area cities within those regions to evaluate RTES performance across different climates and subsurface conditions: Albuquerque, New Mexico; Charleston, South Carolina; Chicago and Decatur, Illinois; Lansing, Michigan; Memphis, Tennessee; Phoenix, Arizona; and Portland, Oregon. Evaluated metrics include estimated required well spacing, thermal storage capacity, and thermal recovery efficiency through time. Also considered for each reservoir are potential complicating factors, including reservoir depth, thermally driven free convection, and groundwater salinity. This work focuses on direct-use cooling because the need for cooling modern office buildings greatly exceeds that for heating in most parts of the country (Falta and others, 2016); however, the evaluated metrics are also relevant to heating and electricity applications. Results indicate that favorable RTES conditions exist in each region, with the Coastal Plain and Basin and Range being especially favorable for thermal storage capacity, while the Pacific Northwest and Michigan Basin excel at energy recovery for the evaluated cooling application. The results underscore the utility of developing maps of thermal storage capacity, subsurface temperature models, and volumetric estimates of thermal storage capacity to serve as key RTES resource classification standards. Overall, this pre-assessment provides a basic understanding of RTES potential in several cities and geologic regions throughout the country and will aid ongoing thermal energy storage assessment efforts.

Arizona, Illinois, Michigan, New Mexico, Oregon, S↗

USGS2023

City-scale geothermal energy everywhere to support renewable resilience – A transcontinental cooperation

Cities have important and varying incentives to transform their energy sector to all-electric with low carbon emissions. However, they often encounter a number of impediments when attempting to implement such a change. For example, while urban areas have the highest energy demand-density, cities often lack the space for installing additional energy generation and/or long-duration energy storage systems. Cities also have existing environmental issues from energy sources (e.g., pollution from dust, waste heat or noise) that make residents sensitive to energy infrastructure development. Utilizing power from conventional sources, such as natural gas, biomass and hydropower, which usually are distanced from the urban areas, also make cities more vulnerable to supply disruptions. One promising de-carbonizing energy option for cities focuses on their heating and cooling needs, which constitutes around 1/3 of U.S. and 1/2 of European energy consumption (including industrial processes like drying, pasteurization, etc.; Jadun and others, 2017; EU Commission 2022). If heating and cooling loads can be met by geothermal direct-use technologies, then the need for new electric sources can be greatly lessened. Despite the proven efficacy of geothermal energy as a city/community-scale heating and cooling resource, it is currently only a niche resource in the heating and cooling sector, though has significant potential for future growth. Historically, emphasis has been placed on geothermal electricity generation potential that requires higher temperature (greater than 90 °C) resources at drillable depths, but potentially viable areas are geographically limited and typically well removed from urban centers. Key drivers for investments were represented by greater political interest in renewable electricity production, higher revenues and less effort in distributing the produced energy via grids. In contrast, low-temperature (less than 90 °C) geothermal resources can be used directly for heating and cooling almost everywhere and are cost-effective in urban/suburban settings. In addition, the increased prominence of renewable electricity sources, such as wind and solar onto city-scale electric grids, has led to new urgency around questions of energy storage. Underground thermal energy storage (UTES), wherein surplus or waste heat is stored underground for later use, could present a long-duration energy storage solution. From October 2022 through September 2024, a transcontinental consortium consisting of geological surveys, geoscience organizations, industry representatives and universities aims to develop an understanding of the global potential for city-scale geothermal, proposing guidelines to aid in promoting the economic utilization of low temperature geothermal resources. Efforts will focus on providing city managers and other decision makers with the information needed to evaluate and implement suitable city/community-scale geothermal technologies. Funded by the U.S. Geological Survey’s John Wesley Powell Center for Analysis and Synthesis, this interdisciplinary consortium will showcase tools, datasets, and scientific recommendations to accelerate the broader understanding and adoption of renewable energy systems that access geothermal resources. The collaborative research activities include standardization of nomenclatures, resource description and characterization strategies globally. The results from these activities will be combined with a preliminary climate-driven, city-based energy needs related analysis to perform energy supply/demand matching analysis. The identification of city-specific applications that would benefit from the geothermal technologies provides the basis to up-scale city-specific determinations to regional and national assessments of resource estimates. The city-scale geothermal energy research initiative will ultimately provide the synergies and management analysis that can address benefits, environmental impacts, regulatory frameworks, sustainability, and suitability in retrofitted buildings or new as well as existing heating networks.

Conference Paper↗

USGS2022

Hydrogeology and groundwater quality in the San Agustin Basin, New Mexico, 1975–2019

This report describes the findings of a U.S. Geological Survey study, completed in cooperation with the Bureau of Land Management, focused on better understanding the present-day (1975–2019) hydrogeology and groundwater quality of the San Agustin Basin in west-central New Mexico to support sustainable groundwater resource management. The basin hosts a relatively undeveloped basin-fill and alluvium aquifer system and is topographically divided into east and west subbasins by the McClure Hills. Groundwater chemistry and groundwater elevation data were compiled, collected, and interpreted in the context of groundwater flow and quality. The analyses presented in this report consider groundwater chemistry data collected within the last decade (2010–19) and groundwater elevation data collected from 1975 through 2019 to provide insight into present-day conditions. Groundwater elevations show that groundwater typically moves from the highlands to the lowlands, with a prominent east to west regional trend. Groundwater elevations were lowest in the southwestern portion of the west subbasin, where estimated flow directions suggest underflow through the local highlands into the northern East Fork Gila River watershed, which is further supported by historical groundwater elevation data from the northern East Fork Gila River watershed. Gradual groundwater elevation gradients (about 2 feet per mile) near the east and west subbasin divide suggest that groundwater slowly flows from the east subbasin to the west subbasin. Quantitative analyses of groundwater chemistry data show that groundwater in both subbasins has similar chemical characteristics. A systematic east to west groundwater evolution in water chemistry was not observed despite evidenced subbasin connectivity. The absence of this pattern suggests that groundwater mixing is regionally prevalent, sediment reactivity is low and variable, and (or) recharge conditions are comparable in both subbasins. Groundwater chemistry was generally independent of aquifer type, suggesting that the aquifers are hydrologically well connected. Corrected carbon-14 groundwater age estimates in the basin ranged from 232 to 13,916 years before present with a median of 5,409 years. A wide range of groundwater ages is therefore present in the basin, with waters commonly being thousands of years old, thereby supporting generally slow regional groundwater movement. A component of relatively young groundwater, for which estimated ages could not be accurately computed, is also present in the basin, and it may commonly mix with older waters. The spatial distribution of categorical and quantitative groundwater ages indicates that most recharge likely occurs in the highlands through mountain-block recharge and as focused recharge within arroyos, although evidence of modern (1953 and after) groundwater was minimal at sampled sites. Median annual gradients (groundwater elevation change over time) indicate that most groundwater elevations in the lowlands changed little (−0.2 to 0.2 foot per year) from 1975 through 2019. Groundwater elevations in the highlands varied more annually, which is likely due to recharge from precipitation events. These more variable groundwater elevations in the highlands compared with the lowlands, along with groundwater ages, provide further evidence that most groundwater recharge takes place in the highlands, with minimal recharge in the lowlands. Median groundwater elevation change for all sites was −0.05 foot per year. Temporal consistency of lowland groundwater elevations suggests that regional groundwater dynamics have been more or less stable through time under current climate and development conditions, although median annual gradients indicate that groundwater elevations may have slightly declined on average between 1975 and 2019.

New Mexico↗

USGS2022

Mesilla / Conejos-Médanos Basin: U.S.-Mexico transboundary water resources and research needs

Synthesizing binational data to characterize shared water resources is critical to informing binational management. This work uses binational hydrogeology and water resource data in the Mesilla/Conejos-Médanos Basin (Basin) to describe the hydrologic conceptual model and identify potential research that could help inform sustainable management. The Basin aquifer is primarily composed of continuous basin-fill Santa Fe Group sediments, allowing for transboundary throughflow. Groundwater flow, however, may be partially or fully restricted by intrabasin uplifts and limited recharge. The shallow groundwater in the Rio Grande alluvium receives recharge from the Rio Grande and responds to changes in water supply and demand. About 11% of Rio Grande alluvial groundwater volume is recharged annually, an amount that is less than recent withdrawals. Potentially recoverable fresh to slightly brackish groundwater was estimated at 82,600 cubic hectometers in the U.S. portion of the Basin and 69,100 cubic hectometers in the Mexican portion. Alluvial groundwater geochemistry is governed by the evaporative concentration of the Rio Grande and agricultural diversions, whereas deeper groundwater geochemistry is governed by mixing and geochemical processes. Continued refinements to storage estimates, the water budget, and deep groundwater extent and geochemistry can improve estimates of sustainable use and inform alternative water sources.

Mesilla/Conejos-Médanos Basin↗

USGS2022

Discovering hidden geothermal signatures using non-negative matrix factorization with customized k-means clustering

Discovery of hidden geothermal resources is challenging. It requires the mining of large datasets with diverse data attributes representing subsurface hydrogeological and geothermal conditions. The commonly used play fairway analysis approach typically incorporates subject-matter expertise to analyze regional data to estimate geothermal characteristics and favorability. We demonstrate an alternative approach based on machine learning (ML) to process a geothermal dataset from southwest New Mexico (SWNM). The study region includes low- and medium-temperature hydrothermal systems. Several of these systems are not well characterized because of insufficient existing data and limited past explorative work. This study discovers hidden patterns and relations in the SWNM geothermal dataset to improve our understanding of the regional hydrothermal conditions and energy-production favorability. This understanding is obtained by applying an unsupervised ML algorithm based on non-negative matrix factorization coupled with customized k-means clustering (NMFk). NMFk can automatically identify (1) hidden signatures characterizing analyzed datasets, (2) the optimal number of these signatures, (3) the dominant data attributes associated with each signature, and (4) the spatial distribution of the extracted signatures. Here, NMFk is applied to analyze 18 geological, geophysical, hydrogeological, and geothermal attributes at 44 locations in SWNM. Using NMFk, we find data patterns and identify the spatial associations of hydrothermal signatures within two physiographic provinces (Colorado Plateau and Basin and Range) and two sub-regions of these provinces (the Mogollon-Datil volcanic field and the Rio Grande rift) in SWNM. The ML algorithm extracted five hydrothermal signatures in the SWNM datasets that differentiate between low (<90) and medium (90-150)-temperature hydrothermal systems. The algorithm also suggests that the Rio Grande rift and northern Mogollon-Datil volcanic field are the most favorable regions for future geothermal resource discovery. NMFk also identified critical attributes to identify medium-temperature hydrothermal systems in the study area. The resulting NMFk model can be applied to predict geothermal conditions and their uncertainties at new SWNM locations based on limited data from unexplored regions. The code to execute the performed analyses as well as the corresponding data can be found at https://github.com/SmartTensors/GeoThermalCloud.jl.

New Mexico↗

USGS2021

Salinity contributions from geothermal waters to the Rio Grande and shallow aquifer system in the transboundary Mesilla (United States)/Conejos-Médanos (Mexico) Basin

Freshwater scarcity has raised concerns about the long-term availability of the water supplies within the transboundary Mesilla (United States)/Conejos-Médanos (Mexico) Basin in Texas, New Mexico, and Chihuahua. Analysis of legacy temperature data and groundwater flux estimates indicates that the region’s known geothermal systems may contribute more than 45,000 tons of dissolved solids per year to the shallow aquifer system, with around 8500 tons of dissolved solids being delivered from localized groundwater upflow zones within those geothermal systems. If this salinity flux is steady and eventually flows into the Rio Grande, it could account for 22% of the typical average annual cumulative Rio Grande salinity that leaves the basin each year—this salinity proportion could be much greater in times of low streamflow. Regional water level mapping indicates upwelling brackish waters flow towards the Rio Grande and the southern part of the Mesilla portion of the basin with some water intercepted by wells in Las Cruces and northern Chihuahua. Upwelling waters ascend from depths greater than 1 km with focused flow along fault zones, uplifted bedrock, and/or fractured igneous intrusions. Overall, this work demonstrates the utility of using heat as a groundwater tracer to identify salinity sources and further informs stakeholders on the presence of several brackish upflow zones that could notably degrade the quality of international water supplies in this developed drought-stricken region.

Chuhuahua, New Mexico, Texas↗

USGS2021

Machine learning to identify geologic factors associated with production in geothermal fields: A case-study using 3D geologic data, Brady geothermal field, Nevada

In this paper, we present an analysis using unsupervised machine learning (ML) to identify the key geologic factors that contribute to the geothermal production in Brady geothermal field. Brady is a hydrothermal system in northwestern Nevada that supports both electricity production and direct use of hydrothermal fluids. Transmissive fluid-flow pathways are relatively rare in the subsurface, but are critical components of hydrothermal systems like Brady and many other types of fluid-flow systems in fractured rock. Here, we analyze geologic data with ML methods to unravel the local geologic controls on these pathways. The ML method, non-negative matrix factorization with k -means clustering (NMF k ), is applied to a library of 14 3D geologic characteristics hypothesized to control hydrothermal circulation in the Brady geothermal field. Our results indicate that macro-scale faults and a local step-over in the fault system preferentially occur along production wells when compared to injection wells and non-productive wells. We infer that these are the key geologic characteristics that control the through-going hydrothermal transmission pathways at Brady. Our results demonstrate: (1) the specific geologic controls on the Brady hydrothermal system and (2) the efficacy of pairing ML techniques with 3D geologic characterization to enhance the understanding of subsurface processes.

Nevada↗

USGS2021

3-D geologic controls of hydrothermal fluid flow at Brady geothermal field, Nevada, USA

In many hydrothermal systems , fracture permeability along faults provides pathways for groundwater to transport heat from depth. Faulting generates a range of deformation styles that cross-cut heterogeneous geology, resulting in complex patterns of permeability, porosity, and hydraulic conductivity. Vertical connectivity (a throughgoing network of permeable areas that allows advection of heat from depth to the shallow subsurface) is rare and is confined to relatively small volumes that have highly variable spatial distribution. This local compartmentalization of connectivity represents a significant challenge to understanding hydrothermal circulation and for exploring, developing, and managing hydrothermal resources. Here, we present an evaluation of the geologic characteristics that control this compartmentalization in hydrothermal systems through 3-D analysis of the Brady geothermal field in western Nevada. A published 3-D geologic map of the Brady area is used as a basis to develop structural and geological variables that are hypothesized to control or effect permeability or connectivity. The 3-D distribution of these variables is compared to the distribution of productive and non-productive fluid flow intervals along production wells and non-productive wells via principal component analysis (PCA). This comparison elucidates which geologic and structural variables are most closely associated with productive fluid flow intervals. Results indicate that production intervals at Brady are located: (1) within or near to known and stress-loaded macro-scale faults, and (2) in areas of high fault and fracture density.

Nevada↗

USGS2021

National-scale reservoir thermal energy storage pre-assessment for the United States

The U.S. Geological Survey is performing a pre-assessment of the cooling potential for reservoir thermal energy storage (RTES) in five generalized geologic regions (Basin and Range, Coastal Plains, Illinois Basin, Michigan Basin, Pacific Northwest) across the United States. Reservoir models are developed for the metropolitan areas of eight cities (Albuquerque, New Mexico; Charleston, South Carolina; Chicago and Decatur, Illinois; Lansing, Michigan; Memphis, Tennessee; Phoenix, Arizona; and Portland, Oregon) so that computed metrics can be compared to evaluate RTES potential across diverse climates, geologic settings, and physiography. Permeable, semi-confined/confined units that underlie more-utilized aquifers and contain low-quality groundwater are selected for each city. Energy storage metrics are computed for the anticipated total thickness of stratigraphy for which RTES might be feasible, including estimated required well spacing, thermal storage capacity, and thermal recovery efficiency over time. Falta et al. (2016) showed that for a modern 25,000 square-foot (2,323 square-meter), two-story office building, cooling needs exceed heating demand for almost every region of the country. We therefore use Falta et al.’s cooling demand for each city as the representative RTES stress condition for metric computation, allowing comparisons across regions. Results indicate that favorable RTES conditions exist in each region, particularly in the Illinois Basin, Coastal Plains, and Basin and Range. Thermal recovery efficiencies are very high in all regions and increase over time. The thermal storage capacity metric is most informative in the pre-assessment and underscores the importance of mapping reservoir thicknesses and porosities to permit detailed mapping of thermal storage capacity per unit area as a key RTES resource classification standard. This assessment provides a basic understanding of the RTES potential in several metropolitan areas and geologic regions throughout the United States and will aid further evaluation of national RTES efficacy.

Conference Paper↗

USGS2020

Optimization assessment of a groundwater-level observation network in the Middle Rio Grande Basin, New Mexico

The U.S. Geological Survey, in cooperation with the Albuquerque Bernalillo County Water Utility Authority (ABCWUA), measures groundwater levels continuously (hourly) and discretely (semiannually and annually) at a network of wells and piezometers (hereafter called the observation network) within the Middle Rio Grande Basin in central New Mexico. Groundwater levels that are measured in this observation network provide a long-term hydrologic dataset that is heavily relied upon to make water management decisions. The desire to upgrade and perform maintenance on this observation network initiated this study, which assesses the spatial and temporal importance of measurements towards optimization of monitoring the observation network to reduce or redirect monitoring costs. This report describes the methods and results of the optimization assessment of this observation network, which included separate spatial and temporal methodologies and an evaluation using principal component analysis (PCA). Results from the spatial optimization assessment can be used to help identify observation network sites that do not significantly affect the generation of winter groundwater-elevation contour maps of the production zone. Results from the temporal optimization assessment and PCA can also be consulted when deciding which sites to remove from the network, especially for sites that are monitored more frequently than annually. Results from the temporal optimization assessment can be used to inform the minimum monitoring frequency at the observation network required to capture the trends shown in higher frequency monitoring. The PCA results distinguish spatially distributed characteristic water-level trends that can inform the management decisions that are made when using the spatial and temporal optimization assessment results. Reducing the temporal frequency or spatial density of monitoring is ultimately a management decision that depends on the amount of data loss or degradation that is deemed acceptable while still meeting the network objectives of the ABCWUA. This study can also serve as a starting point to a data gap analysis of local aquifer characteristics and help guide enhanced observation network design as needs arise or in advance of future water management decisions. The results of the spatial optimization assessment indicate that as many as about 20 specified sites can be removed from the observation network with a relatively small loss in the ability to represent the kriged groundwater-elevation surfaces of the production zone that were generated by using median groundwater elevations for two periods: the 2001 time interval and 2015 time interval. This analysis also demonstrated the importance of wells at the margin of the study area and in areas where there are large hydrologic gradients. At many of the 47 hourly monitored sites analyzed in the temporal optimization assessment, temporal trends were well represented for at least one of the reduced monitoring frequencies tested, indicating that a reduced frequency may be sufficient to adequately characterize seasonal and long-term trends. PCA and k-means clustering analysis of the 15 hourly monitored sites that are screened within the production zone indicate that the sites can be categorized into four groups, or clusters, of differing groundwater-level hydrograph characteristics. Except for one cluster, all of the clusters have the potential to be well represented by fewer index monitoring sites.

New Mexico↗