Geology topics

James C. Hower

Publications and source records attributed to James C. Hower.

At least 19 recordsLinked to original sources

USGS2026

Rare earth element potential in coal and coal ash in the U.S. Gulf Coast

United States heavy reliance on imports of critical minerals (CMs), including rare earth elements (REEs), underscores the importance of development of domestic sources. The study objective was to quantify CM and REE concentrations in coal and coal ash in the US Gulf Coast region. CM and REE concentrations were measured for 118 samples from outcrops and 14 mines in the Gulf Coast. Results show that total REE + Yttrium (REY) concentrations (dry coal basis) are comparable to those of the upper continental crust (UCC) with localized hot spots, such as the Texas Gibbons Creek mine (REY ≤ ~ 2860 ppm). When normalized to UCC REY concentration (169 ppm, dry coal basis), REY to UCC ratios for Gulf Coast coal samples range from 0.1 to 17 (median ratio 0.6). REE extractability from lignites is high (median: 63%–93%) using environmentally benign weak acid. In addition to raw coal, coal ash from power plants could also serve as an REE source with a median ratio of REY in ash relative to coal of 4; however, extractability from coal ash is generally much lower (≤ 5% using the same weak acid as in coal). The median basket price for extracted REY as oxides from coal, assuming 70% extractability, is $3.2 per tonne of coal and $186 billion based on 58 billion metric tonnes of dry coal in the Gulf Coast. REEs important for magnets (Pr + Nd + Tb + Dy) account for ~ 80% of the total value. The corresponding median basket price for extracted REY as oxides from coal ash, assuming ~ 30% extractability, is ~$4.4 per tonne of ash and $1.2 billion based on 258 million tonnes of ash. REE production from coal would likely require co-products, such as activated carbon or humic acids, to attain economic viability. Production of REEs from coal ash could offset remediation costs related to potential water contamination. This reconnaissance study shows the potential for REE production from coal and coal ash in the Gulf Coast; however, carbon coproducts and/or societal benefits would likely be required for socioeconomic viability.

Alabama, Florida, Louisiana, Mississippi, Texas↗

USGS2025

Component identification of solid biomass fuels using reflected light microscopy: Interlaboratory study 2

As nations transition toward sustainable energy systems , biomass has become a vital component of global energy portfolios. Derived from organic materials such as wood, agricultural residues, forestry byproducts, and organic waste, biomass is a renewable energy source with significant environmental and economic benefits. Responsible biomass energy production can improve waste management, reduce emissions of greenhouse gases, and mitigate environmental pollution. However, as the diversity of biomass-derived fuels increases, robust quality assessment methods are essential to ensure their efficiency, safety, and minimal environmental impact. Reflected light microscopy (RLM) is one such technique with the potential to complement conventional physico-chemical analyses by enabling a rapid identification of material constituents and impurities. To refine this methodology and evaluate the reproducibility of solid biomass component identification using RLM, an interlaboratory study (ILS) was conducted. The study involved the recognition of 58 components across 45 photomicrographs, with the participation of 65 scientists and students from 25 countries. The participants faced high difficulty identifying some of the marked components, and as a result, the percentage of correct answers ranged from 19.0 % to 98.3 %, with an average correct identification rate of 62.7 %. The most challenging aspects of the identification process included distinguishing between woody and non-woody (agro) biomass, accurately identifying petroleum-derived materials, and differentiating agro biomass from inorganic matter. The results suggest that while RLM is an important tool for characterizing solid biomass, further development of methodology guidelines and training are necessary to enhance its effectiveness. Future research should prioritize preparing detailed, image-rich, microscopic morphological descriptions of biomass fuel components, which could improve the accuracy and reliability of using RLM in biomass fuel characterization.

International Journal of Coal Geology↗

USGS2025

Gulf Coast Basin CORE-CM initiative final report

The Bureau of Economic Geology at the University of Texas at Austin (UT-BEG) is leading the Gulf Coast Carbon Ore, Rare Earth, and Critical Minerals (CORE-CM) Initiative to assess the potential to produce critical minerals (CMs), including rare earth elements (REEs) from coal, coal ash, and produced water related to oil and gas production, and related materials (alumina processing waste [red mud], heavy mineral sands, graphite, and zeolite) within the Gulf Coast Basin. This project represents the first phase in a long-term program and provides reconnaissance data that will be foundational for future work by assessing resources and suggesting plans to be conducted in future work and expanding stakeholder engagement. The project includes several tasks designed to identify, characterize, and assess several necessary aspects for development of CMs and REEs in the Gulf Coast Basin.

Gulf Coast basin↗

USGS2024

Rare Earth Elements in coal fly ash and their potential recovery

Coal fly ash is a potential resource of valuable elements, such as rare earth elements (REEs), which are retained and concentrated upon combustion. Understanding REE occurrence within fly ash is vital to developing recovery methods. Some of the highest REE contents occur in fly ash derived from U.S. Appalachian Basin coals, and coals influenced by input volcanic ash are especially enriched. Leaching studies of bulk fly ash show that, as a proportion of the total REEs present, samples from eastern U.S. coals are generally less extractable than fly ash derived from lower REEs western U.S. coals. Aluminosilicate glasses formed during combustion comprise the largest mass fraction of coal fly ash. REE-enriched domains are present locally in fly ash at the nanometer scale. Annual fly ash production, combined with coal ash already in storage, makes up a large resource for potential recovery of rare earths and associated critical elements. Further extraction technology developments are needed to overcome difficulties in REE concentration and purification to produce coal-ash-derived REE materials of saleable purity.

Book chapter↗

USGS2024

Atlas of microscopic images of biochar using reflected light microscopy in biochar characterization

Derived through the thermochemical conversion of biomass, biochar is a carbon-rich substance recognized for its significance in environmental applications and sustainable agriculture. As interest in its utilization continues to rise, it becomes crucial to comprehend how the source material and pyrolysis parameters influence the properties of biochar and, consequently, to research the suitability of various analytical methods for characterizing it. Despite the current utilization of numerous physical and chemical methods, the untapped potential of reflected light microscopy warrants further exploration. While a few recent studies suggest a correlation between certain microscopic characteristics and selected physical and chemical properties of biochar, the data are limited and difficult to compare. This is primarily due to variations in the types of original biomass used and lack of information about pyrolysis conditions. Moreover, because only a limited number of photographs taken under a reflected light microscope are publicly available to-date, it is difficult to evaluate morphological differences between various biochars and other organic materials such as inertinites from coal, charcoal, etc. To address limited availability of publicly available data, this “Atlas of Microscopic Images of Biochar” presents a collection of more than 300 images contributed by researchers from Poland, the United States, Canada, Australia, Brazil, and Denmark. These photomicrographs capture optical characteristics of a diverse array of biochar, demonstrating its unique morphological and structural features. This visual documentation can serve as a valuable resource for researchers, industry professionals, educators, and enthusiasts interested in investigating the complexities of biochar forms.

Indiana Journal of Earth Sciences↗

USGS2023

Distribution of rare earth and other critical elements in lignites from the Eocene Jackson Group, Texas

Coal is increasingly evaluated as a source of rare earth elements (REEs) in the United States to address the overreliance on imported REEs. The objective of this study was to assess the distribution of REEs in lignites from selected mining areas in the Texas Gulf Coastal Plain region. Thirty-one archived lignite and rock samples previously collected by the U.S. Geological Survey were analyzed for their rare earth element and critical mineral content. These include samples from one core (5400 and 5500 lignite horizons) and two opencast lignite mines (Gibbons Creek 3500 and 4500 horizons, and San Miguel horizons A to D) in the Eocene Jackson Group of the Texas Gulf of Mexico Coastal Plain. Some lithologies in the Gibbons Creek 3500 and 4500 lignite-bearing sections have high total rare earth, yttrium (Y), and scandium (Sc) (REYSc) values, up to 7800 ppm (ash basis) REYSc. The lignite lithologies show an enrichment in rare earths, [samarium (Sm) through gadolinium (Gd)]. The basal Gibbons Creek 3500 lignite bench shows a heavy rare earth element enrichment pattern resembling that often seen in peats through high volatile A bituminous coals. The 5500 lignite sequence, overlying the latter lignite sections, shows a light rare earth enrichment. The San Miguel lignite benches have heavy rare earth enrichments with a negative europium (Eu) anomaly.

Texas↗

USGS2023

Interlaboratory study: Testing reproducibility of solid biofuels component identification using reflected light microscopy

Considering global market trends and concerns about climate change and sustainability, increased biomass use for energy is expected to continue. As more diverse materials are being utilized to manufacture solid biomass fuels, it is critical to implement quality assessment methods to analyze these fuels thoroughly. One such method is reflected light microscopy (RLM), which has the potential to complement and enhance current standard testing, leading to improving fuel quality assessment and, ultimately, preventing avoidable air pollution. An interlaboratory study (ILS) was conducted to test the reproducibility of biomass fuels component identification using a reflected light microscopy technique. The exercise was conducted on thirty photomicrographs showing biomass and various undesired components (like plastics or mineral matter), which were purposely added (by the ILS organizers) to contaminate wood pellets and charcoal-based grilling fuels. Forty-six participants had various levels of difficulty identifying the marked components, and as a result, the percentage of correct answers ranged from 52.2 to 94.4%. Among the most difficult components to distinguish were petroleum products and inorganic matter. Various reasons led to the misidentification, including insufficient morphological descriptions of the components provided to participants, ambiguities of the nomenclature, limitations of the analytical and exercise method, and insufficient experience of the participants. Overall, the results indicate that RLM has the potential to enhance the quality assessment of biomass fuels. However, they also demonstrate that the petrographic classification used in this exercise requires further refinement before it can be standardized. While a new simplified classification of solid biomass fuels components was created as an outcome of this study, future research is necessary to refine the nomenclature, develop a microscopic morphological description of the components, and verify the accuracy of component identification with a follow-up ILS.

International Journal of Coal Geology↗

USGS2021

Coking coal of the United States—Modern and historical coking coal mining locations and chemical, rheological, petrographic, and other data from modern samples

Coking coal, or metallurgical coal, has been produced in the United States for nearly 200 years. Coking coal is primarily used in the production of coke for use in the steel industry, and for other uses (for example, foundries, blacksmithing, heating buildings, and brewing). Currently, U.S. coking coal is produced in Alabama, Arkansas, Pennsylvania, Virginia , and West Virginia. Historically, coking coal has also been produced in 15 other states (Alaska, Colorado, Georgia, Illinois, Indiana, Kentucky, Maryland, Montana, New Mexico, Ohio, Oklahoma, Tennessee, Utah, Washington, and Wyoming), but currently is not. Coals from the Appalachian, Arkoma, and Illinois basins are Pennsylvanian in age, while coals in Alaska, Colorado, Montana, New Mexico, Utah, Washington, and Wyoming range in age from Early Cretaceous through Eocene. This Open-File Report presents the geographic locations of current and historical coking coal deposits of the United States, with additional information about recent and historical mining and exploration activities. Chemical, rheological, petrographic, and other criteria for evaluating the coking potential of coals are discussed, and historical data for coking coals in the United States are presented. In addition, new coking coal samples from Alabama, Arkansas, Kentucky, and Oklahoma were collected and analyzed for this report, and the data are presented in multiple tables, including proximate and ultimate analyses; calorific value; sulfur forms; major-, minor-, and trace-element abundances; Free-Swelling Index; Gieseler Plastometer analyses; American Society for Testing and Materials (ASTM) dilatation; coal petrography; and predicted values of Coal Stability Factor and Coal Strength after Reaction with CO 2 (pCSF and pCSR, respectively). Data from previously analyzed coking coal samples in Kentucky, Pennsylvania, Virginia, and West Virginia were supplied by three companies, including results from all the tests listed above, plus oxidation, Hardgrove Grindability Index, and ash fusion (in a reducing environment) temperatures are also presented in tables in the report. Geographic Information System (GIS) data compiled for this project are available for download for public and private utilization and may be used to create maps for a variety of energy resource studies. These GIS data are in shapefile format, and metadata files are included describing all GIS processing. Additional geographic information about coking coal areas of the United States are also presented in tabular format in the report, including the following: names of coal basins, fields, regions, districts, and areas; coal beds or zones; geographic locations including States, counties, towns, rivers, mountains, etc.; stratigraphic hierarchy and age of the coal-bearing interval; coking characteristics including sulfur content, ash yield, volatile matter, moisture, calorific value, and Free-Swelling Index; coal rank; names of coal mines and coal-mining companies; current and past mining activity; and references for reports about the coal.

Open-File Report↗

USGS2018

Gas emissions, tars, and secondary minerals at the Ruth Mullins and Tiptop coal mine fires

Both the Tiptop and Ruth Mullins coal fires, Kentucky, were reinvestigated in 2009 and 2010. The Tiptop fire was not as active in 2009 and may have been on the path to burning out at the time of the 2009 visit. The Ruth Mullins coal mine fire, Perry County, Kentucky, has been the subject of several field investigations, including November 2009–February 2010 investigations in which we measured gas emissions, collected minerals and tars, and characterized the nature of the fire. Vents exhibiting the greatest gas flux (>100,000 mg/s/m 2 ) are those with the largest amount of condensate minerals and tars. Vents with moderate gas flux (10,000–100,000 mg/s/m 2 ) are less likely to contain condensate minerals, but are collocated with tars, and vents with the lowest flux (<10,000 mg/s/m 2 ) generally lack both minerals and tars. Aliphatic hydrocarbons present in the gases include C1-C9 compounds, and aromatics include BTEX compounds. Diffuse-CO 2 emissions are concentrated along the fracture zones overlying abandoned mine works. The area of peak diffuse flux corresponds to the trend of the collapsed portal that forms vent 5. The greatest vent emissions were also recorded at vent 5. The snow-melt zone mapped in January 2010 overlies the areas of peak diffuse-CO 2 emissions measured in November; together they delineate the zone of active combustion. Comparison of greenhouse gas emissions from the two sources shows that vent emissions exceed diffuse emissions. The highly fractured, quartz-cemented roof rock funnels the majority of emissions toward the vents. Significant decreases are seen in estimates of yearly greenhouse emissions based on data gathered from November 2009 to February 2010, with estimates from November significantly exceeding any previously published estimates. For example, September 2009 estimates from vent 3 alone indicated that 19 ± 7.5 T CO 2 /yr were emitted while the November 2009 estimates were 1800 ± 690 T/yr. Barometric pressure was lower in November than September. This implies that there are many factors influencing the seasonal variations in fire emissions and that more frequent monitoring will be necessary to derive accurate estimates of coal fires' contribution to the carbon budget.

Kentucky↗

USGS2016

Notes on the origin of copromacrinite based on nitrogen functionalities and δ13C and δ15N determined on samples from the Peach Orchard coal bed, southern Magoffin County, Kentucky

This paper represents the first attempt to show, by means other than just petrographic ones, that one type of macrinite, herein designated copromacrinite, may result from macrofauna feces. For that purpose a combination of coal petrography, X-ray photoelectron spectroscopy, and elemental-analysis continuous-flow isotope ratio mass spectrometry methods were used to determine nitrogen functionalities and δ 13 C and δ 15 N compositions in 1) vitrinite-rich, 2) fusinite + semifusinite-rich, and 3) macrinite-rich (with a possible coprolitic origin) samples of the high volatile A bituminous Peach Orchard coal (Bolsovian; Middle Pennsylvanian) from Magoffin County, Kentucky. There were no significant differences between pyridinic-N and quaternary-N abundance in the three samples, however, pyrrolic-N was higher (~ 54%) in the macrinite-rich sample than in the other two samples (~ 38%). The data suggest that pyridinic-N and quaternary-N are independent of maceral group composition and that pyrrolic-N is dependent on maceral composition (fusinite + semifusinite versus macrinite). δ 13 C values obtained for bulk and demineralized coal of the vitrinite- and fusinite + semifusinite-rich samples are similar with δ 13 C values of − 24.80 ± 0.01&permil; VPDB and − 24.61 ± 0.09&permil; VPDB for bulk samples and − 24.81 ± 0.07&permil; VPDB and − 24.52 ± 0.04&permil; VPDB for demineralized samples. These values are within the expected range for vitrinite-rich samples and the slightly higher δ 13 C value of the fusinite + semifusinite-rich sample is expected as δ 13 C values for inertinite are higher than for vitrinite. However, there was a significant shift to a lower δ 13 C value (− 26.80 ± 0.01&permil; VPDB for the bulk sample value) for the macrinite-rich sample. Because the samples are basically isorank, and δ 13 C (and δ 15 N) shifts do not occur during maturation until anthracite rank, the difference may be related to the presence or composition of the macrinite within the sample which lacks heat-effect indicators, such as devolatilization vacuoles and distorted pores. δ 15 N values are also similar for bulk and demineralized coal of the vitrinite- and fusinite + semifusinite-rich samples, and the bulk values were heavier in this samples (3.07 ± 0.03&permil; Air and 2.92 ± 0.10&permil; Air, respectively), and much lighter (− 2.83 ± 0.09&permil; Air) for the macrinite-rich sample. The study of Peach Orchard coal samples using reflected-light microscopy, isotopic composition, and nitrogen-forms analyses revealed that the macrinite-rich sample contains macrinite with coprolitic features (e.g. oxidation rind, mix of undigested palynomorphs, frequent and randomly located funginite, agglutination pulp of semifusinite reflectance, internal lack of bedding fabric, and suggestion of structures resulting from intestines and stomach walls), more pyrrolic-N (~ 16%), and lower δ 13 C (~ 2&permil; VPDB) and δ 15 N (~ 4&permil; Air) values than the vitrinite and semifusinite + fusinite rich samples. These findings suggest that the maceral macrinite has multiple origins based on petrography and measurable chemical differences between the macrinite, vitrinite, and semifusinite + fusinite fractions within the coal. Assuming that copromacrinite observed is an excretion then the anomalies observed may result from the symbiotic relations between the macrofauna (e.g. cockroaches) and microbiota during the digestive processes, and the nitrogen balance mechanisms inside macrofauna body.

Kentucky↗

USGS2014

Petrographic maturity parameters of a Devonian shale maturation series, Appalachian Basin, USA. ICCP Thermal Indices Working Group interlaboratory exercise

This paper presents results of an interlaboratory exercise on organic matter optical maturity parameters using a natural maturation series comprised by three Devonian shale samples (Huron Member, Ohio Shale) from the Appalachian Basin, USA. This work was conducted by the Thermal Indices Working Group of the International Committee for Coal and Organic Petrology (ICCP) Commission II (Geological Applications of Organic Petrology). This study aimed to compare: 1. maturation predicted by different types of petrographic parameters (vitrinite reflectance and spectral fluorescence of telalginite), 2. reproducibility of the results for these maturation parameters obtained by different laboratories, and 3. improvements in the spectral fluorescence measurement obtained using modern detection systems in comparison with the results from historical round robin exercises. Mean random vitrinite reflectance measurements presented the highest level of reproducibility (group standard deviation 0.05) for low maturity and reproducibility diminished with increasing maturation (group standard deviation 0.12). Corrected fluorescence spectra, provided by 14 participants, showed a fair to good correspondence. Standard deviation of the mean values for spectral parameters was lowest for the low maturity sample but was also fairly low for higher maturity samples. A significant improvement in the reproducibility of corrected spectral fluorescence curves was obtained in the current exercise compared to a previous investigation of Toarcian organic matter spectra in a maturation series from the Paris Basin. This improvement is demonstrated by lower values of standard deviation and is interpreted to reflect better performance of newer photo-optical measuring systems. Fluorescence parameters measured here are in good agreement with vitrinite reflectance values for the least mature shale but indicate higher maturity than shown by vitrinite reflectance for the two more mature shales. This red shift in λ max beyond 0.65% vitrinite reflectance was also observed in studies of Devonian shale in other basins, suggesting that the accepted correlation for these two petrographic thermal maturity parameters needs to be re-evaluated. A good linear correlation between λ max and T max for this maturation series was observed and λ max 600 nm corresponds to T max of 440 °C. Nevertheless if a larger set of Devonian samples is included, the correlation is polynomial with a jump in λ max ranging from 540 to 570 nm. Up to 440 °C of T max , the λ max , mostly, reaches up to 500 nm; beyond a T max of 440 °C, λ max is in the range of 580–600 nm. This relationship places the “red shift” when the onset of the oil window is reached at T max of 440 °C. Moreover, the correlation between HI and λ max (r 2 = 0.70) shows a striking inflection and decrease in HI above a λ max of 600 nm, coincident with the approximate onset of hydrocarbon generation in these rocks.

International Journal of Coal Geology↗

USGS2014

Thermal maturity patterns in Pennsylvanian coal-bearing rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania

Thermal maturation patterns of Pennsylvanian strata in the Appalachian basin and part of the Black Warrior basin were determined by compiling previously published and unpublished percent-vitrinite-reflectance (%R 0 ) measurements and preparing isograd maps on the basis of the measurements. The isograd values range from 0.6 %R 0 in Ohio and the western side of the Eastern Kentucky coal field to 5.5 %R 0 in the Southern field in the Pennsylvania Anthracite region, Schuylkill County, Pa. The vitrinite-reflectance values correspond to the American Society of Testing Materials (ASTM) coal-rank classes of high-volatile C bituminous to meta-anthracite, respectively. In general, the isograds show that thermal maturity patterns of Pennsylvanian coals within the Appalachian basin generally decrease from east to west. In the Black Warrior basin of Alabama, the isograds show a circular pattern with the highest values (greater than 1.6 %R 0 ) centered in Jefferson County, Ala. Most of the observed patterns can be explained by variations in the depth of burial, variations in geothermal gradient, or a combination of both; however, there are at least four areas of higher ranking coal in the Appalachian basin that are difficult to explain by these two processes alone: (1) a set of west- to northwest-trending salients centered in Somerset, Cambria, and Fayette Counties, Pa.; (2) an elliptically shaped, northeast-trending area centered in southern West Virginia and western Virginia; (3) the Pennsylvania Anthracite region in eastern Pennsylvania; and (4) the eastern part of the Black Warrior coal field in Alabama. The areas of high-ranking coal in southwestern Pennsylvania, the Black Warrior coal field, and the Pennsylvania Anthracite region are interpreted here to represent areas of higher paleo-heat flow related to syntectonic movement of hot fluids towards the foreland associated with Alleghanian deformation. In addition to the higher heat flow from these fluids, the Pennsylvania Anthracite region also was buried more deeply than other parts of the Appalachian basin. The area of high rank coal in southwestern Virginia probably was controlled primarily by overburden thickness, but may also have been influenced by higher geothermal gradients.

Appalacian basin↗

USGS2013

Direct estimation of diffuse gaseous emissions from coal fires: current methods and future directions

Coal fires occur in nature spontaneously, contribute to increases in greenhouse gases, and emit atmospheric toxicants. Increasing interest in quantifying coal fire emissions has resulted in the adaptation and development of specialized approaches and adoption of numerical modeling techniques. Overview of these methods for direct estimation of diffuse gas emissions from coal fires is presented in this paper. Here we take advantage of stochastic Gaussian simulation to interpolate CO 2 fluxes measured using a dynamic closed chamber at the Ruth Mullins coal fire in Perry County, Kentucky. This approach allows for preparing a map of diffuse gas emissions, one of the two primary ways that gases emanate from coal fires, and establishing the reliability of the study both locally and for the entire fire. Future research directions include continuous and automated sampling to improve quantification of gaseous coal fire emissions.

International Journal of Coal Geology↗

USGS2013

Whole-coal versus ash basis in coal geochemistry: a mathematical approach to consistent interpretations

Several standard methods require coal to be ashed prior to geochemical analysis. Researchers, however, are commonly interested in the compositional nature of the whole-coal, not its ash. Coal geochemical data for any given sample can, therefore, be reported in the ash basis on which it is analyzed or the whole-coal basis to which the ash basis data are back calculated. Basic univariate (mean, variance, distribution, etc.) and bivariate (correlation coefficients, etc.) measures of the same suite of samples can be very different depending which reporting basis the researcher uses. These differences are not real, but an artifact resulting from the compositional nature of most geochemical data. The technical term for this artifact is subcompositional incoherence. Since compositional data are forced to a constant sum, such as 100% or 1,000,000 ppm, they possess curvilinear properties which make the Euclidean principles on which most statistical tests rely inappropriate, leading to erroneous results. Applying the isometric logratio (ilr) transformation to compositional data allows them to be represented in Euclidean space and evaluated using traditional tests without fear of producing mathematically inconsistent results. When applied to coal geochemical data, the issues related to differences between the two reporting bases are resolved as demonstrated in this paper using major oxide and trace metal data from the Pennsylvanian-age Pond Creek coal of eastern Kentucky, USA. Following ilr transformation, univariate statistics, such as mean and variance, still differ between the ash basis and whole-coal basis, but in predictable and calculated manners. Further, the stability between two different components, a bivariate measure, is identical, regardless of the reporting basis. The application of ilr transformations addresses both the erroneous results of Euclidean-based measurements on compositional data as well as the inconsistencies observed on coal geochemical data reported on different bases.

International Journal of Coal Geology↗

USGS2011

Splint coals of the Central Appalachians: Petrographic and geochemical facies of the Peach Orchard No. 3 split coal bed, southern Magoffin County, Kentucky

The Bolsovian (Middle Pennsylvanian) Peach Orchard coal bed is one of the splint coals of the Central Appalachians. Splint coal is a name for the dull, inertinite-rich lithologies typical of coals of the region. The No. 3 Split was sampled at five locations in Magoffin County, Kentucky and analyzed for petrography and major and minor elements. The No. 3 Split coals contain semifusinite-rich lithologies, up to 48% (mineral-free basis) in one case. The nature of the semifusinite varies with position in the coal bed, containing more mineral matter of detrital origin in the uppermost durain. The maceral assemblage of these terminal durains is dominated by detrital fusinite and semifusinite, suggesting reworking of the maceral assemblage coincident with the deposition of the detrital minerals. However, a durain in the middle of the coal bed, while lithologically similar to the uppermost durains, has a degraded, macrinite-rich, texture. The inertinite macerals in the middle durain have less distinct edges than semifusinites in the uppermost terminal durains, suggesting degradation as a possible path to inertinite formation. The uppermost durain has higher ash and semifusinite contents at the eastern sites than at the western sites. The difference in the microscopic petrology indicates that megascopic petrology alone can be a deceptive indicator of depositional environments and that close attention must be paid to the individual macerals and their implications for the depositional setting, especially within the inertinite group.

International Journal of Coal Geology↗

USGS2011

Quantifying greenhouse gas emissions from coal fires using airborne and ground-based methods

Coal fires occur in all coal-bearing regions of the world and number, conservatively, in the thousands. These fires emit a variety of compounds including greenhouse gases. However, the magnitude of the contribution of combustion gases from coal fires to the environment is highly uncertain, because adequate data and methods for assessing emissions are lacking. This study demonstrates the ability to estimate CO 2 and CH 4 emissions for the Welch Ranch coal fire, Powder River Basin, Wyoming, USA, using two independent methods: (a) heat flux calculated from aerial thermal infrared imaging (3.7–4.4 t d −1 of CO 2 equivalent emissions) and (b) direct, ground-based measurements (7.3–9.5 t d −1 of CO 2 equivalent emissions). Both approaches offer the potential for conducting inventories of coal fires to assess their gas emissions and to evaluate and prioritize fires for mitigation.

International Journal of Coal Geology↗

USGS2011

Geochemical database of feed coal and coal combustion products (CCPs) from five power plants in the United States

The principal mission of the U.S. Geological Survey (USGS) Energy Resources Program (ERP) is to (1) understand the processes critical to the formation, accumulation, occurrence, and alteration of geologically based energy resources; (2) conduct scientifically robust assessments of those resources; and (3) study the impacts of energy resource occurrence and (or) their production and use on both the environment and human health. The ERP promotes and supports research resulting in original, geology-based, non-biased energy information products for policy and decision makers, land and resource managers, other Federal and State agencies, the domestic energy industry, foreign governments, non-governmental groups, and academia. Investigations include research on the geology of oil, gas, and coal, and the impacts associated with energy resource occurrence, production, quality, and utilization. The ERP's focus on coal is to support investigations into current issues pertaining to coal production, beneficiation and (or) conversion, and the environmental impact of the coal combustion process and coal combustion products (CCPs). To accomplish these studies, the USGS combines its activities with other organizations to address domestic and international issues that relate to the development and use of energy resources.

Data Series↗

USGS2010

Geologic controls on thermal maturity patterns in Pennsylvanian coal-bearing rocks in the Appalachian basin

Thermal maturation patterns of Pennsylvanian strata in the Appalachian basin were determined by compiling and contouring published and unpublished vitrinite reflectance (VR) measurements. VR isograd values range from 0.6% in eastern Ohio and eastern Kentucky (western side of the East Kentucky coal field) to greater than 5.5% in eastern Pennsylvania (Southern Anthracite field, Schuylkill County), corresponding to ASTM coal rank classes of high volatile C bituminous to meta-anthracite. VR isograds show that thermal maturity of Pennsylvanian coals generally increases from west to east across the basin. The isograds patterns, which are indicative of maximum temperatures during burial, can be explained by variations in paleodepth of burial, paleogeothermal gradient, or a combination of both. However, there are at least four areas of unusually high-rank coal in the Appalachian basin that depart from the regional trends and are difficult to explain by depth of burial alone: 1) a west-northwestward salient centered in southwestern Pennsylvania; 2) an elliptically-shaped, northeast-trending area centered in southern West Virginia and western Virginia; 3) the eastern part of Black Warrior coal field, Alabama; and 4) the Pennsylvania Anthracite region, in eastern Pennsylvania. High-rank excursions in southwest Pennsylvania, the Black Warrior coal field, and the Pennsylvania Anthracite region are interpreted here to represent areas of higher paleo-heat flow related to syntectonic movement of hot fluids towards the foreland, associated with Alleghanian deformation. In addition to higher heat flow from fluids, the Pennsylvania Anthracite region also experienced greater depth of burial. The high-rank excursion in southwest Virginia was probably primarily controlled by overburden thickness, but may also have been influenced by higher geothermal gradients.

Appalachian basin↗