Geology Reports⌕ Search

Geology topics

Jack K. Odum

Publications and source records attributed to Jack K. Odum.

At least 19 recordsLinked to original sources
USGS2024

Shallow faulting and folding beneath south‐central Seattle, Washington State, from land‐based high‐resolution seismic‐reflection imaging

The geologic framework of the Seattle fault zone (SFZ) has been extensively studied, but the structure and fault strand locations in the central portion of the fault zone through the city of Seattle have remained controversial. Much of what is known about the SFZ has come from light detection and ranging (lidar)‐topographic surveys and paleoseismic investigations of fault scarps primarily west of Puget Sound, regional gravity and aeromagnetic modeling, and multiscale marine seismic imaging in waters both west and east of Seattle. We analyze ∼24 km of land‐based P ‐wave seismic‐reflection data that fill in a critical gap in our understanding of the SFZ beneath the urban areas of West Seattle, south‐central Seattle, and Mercer Island. These data image deformed strata in the upper 1 km, including upwarped Tertiary rock and younger sediments. Collectively, these data provide evidence for multiple Quaternary‐active thrust faults, back thrusts, and sub‐basins within the SFZ beneath the city of Seattle. The results indicate that multiple and potentially active back thrusts in the upper ∼500 m extend across the length of the SFZ and the entire urban corridor that may be analogous to those on Bainbridge Island west of Puget Sound.

Washington↗
USGS2016

Compilation of V S 30 Data for the United States

V S 30 , the time-averaged shear-wave velocity ( V S ) to a depth of 30 meters, is a key index adopted by the earthquake engineering community to account for seismic site conditions. V S 30 is typically based on geophysical measurements of V S derived from invasive and noninvasive techniques at sites of interest. Owing to cost considerations, as well as logistical and environmental concerns, V S 30 data are sparse or not readily available for most areas. Where data are available, V S 30 values are often assembled in assorted formats that are accessible from disparate and (or) impermanent Web sites. To help remedy this situation, we compiled V S 30 measurements obtained by studies funded by the U.S. Geological Survey (USGS) and other governmental agencies. Thus far, we have compiled V S 30 values for 2,997 sites in the United States, along with metadata for each measurement from government-sponsored reports, Web sites, and scientific and engineering journals. Most of the data in our V S 30 compilation originated from publications directly reporting the work of field investigators. A small subset (less than 20 percent) of V S 30 values was previously compiled by the USGS and other research institutions. Whenever possible, V S 30 originating from these earlier compilations were crosschecked against published reports. Both downhole and surface-based V S 30 estimates are represented in our V S 30 compilation. Most of the V S 30 data are for sites in the western contiguous United States (2,141 sites), whereas 786 V S 30 values are for sites in the Central and Eastern United States; 70 values are for sites in other parts of the United States, including Alaska (15 sites), Hawaii (30 sites), and Puerto Rico (25 sites). An interactive map is hosted on the primary USGS Web site for accessing V S 30 data ( https://earthquake.usgs.gov/data/vs30/us/ ).

Data Series↗
USGS2013

Vs30 and spectral response from collocated shallow, active- and passive-source Vs data at 27 sites in Puerto Rico

Shear‐wave velocity (V S ) and time‐averaged shear‐wave velocity to 30 m depth (V S30 ) are the key parameters used in seismic site response modeling and earthquake engineering design. Where V S data are limited, available data are often used to develop and refine map‐based proxy models of V S30 for predicting ground‐motion intensities. In this paper, we present shallow V S data from 27 sites in Puerto Rico. These data were acquired using a multimethod acquisition approach consisting of noninvasive, collocated, active‐source body‐wave (refraction/reflection), active‐source surface wave at nine sites, and passive‐source surface‐wave refraction microtremor (ReMi) techniques. V S ‐versus‐depth models are constructed and used to calculate spectral response plots for each site. Factors affecting method reliability are analyzed with respect to site‐specific differences in bedrock V S and spectral response. At many but not all sites, body‐ and surface‐wave methods generally determine similar depths to bedrock, and it is the difference in bedrock V S that influences site amplification. The predicted resonant frequencies for the majority of the sites are observed to be within a relatively narrow bandwidth of 1–3.5 Hz. For a first‐order comparison of peak frequency position, predictive spectral response plots from eight sites are plotted along with seismograph instrument spectra derived from the time series of the 16 May 2010 Puerto Rico earthquake. We show how a multimethod acquisition approach using collocated arrays compliments and corroborates V S results, thus adding confidence that reliable site characterization information has been obtained.

Bulletin of the Seismological Society of America↗
USGS2012

Characterization of intrabasin faulting and deformation for earthquake hazards in southern Utah Valley, Utah, from high-resolution seismic imaging

We conducted active and passive seismic imaging investigations along a 5.6-km-long, east–west transect ending at the mapped trace of the Wasatch fault in southern Utah Valley. Using two-dimensional (2D) P-wave seismic reflection data, we imaged basin deformation and faulting to a depth of 1.4 km and developed a detailed interval velocity model for prestack depth migration and 2D ground-motion simulations. Passive-source microtremor data acquired at two sites along the seismic reflection transect resolve S-wave velocities of approximately 200 m/s at the surface to about 900 m/s at 160 m depth and confirm a substantial thickening of low-velocity material westward into the valley. From the P-wave reflection profile, we interpret shallow (100–600 m) bedrock deformation extending from the surface trace of the Wasatch fault to roughly 1.5 km west into the valley. The bedrock deformation is caused by multiple interpreted fault splays displacing fault blocks downward to the west of the range front. Further west in the valley, the P-wave data reveal subhorizontal horizons from approximately 90 to 900 m depth that vary in thickness and whose dip increases with depth eastward toward the Wasatch fault. Another inferred fault about 4 km west of the mapped Wasatch fault displaces horizons within the valley to as shallow as 100 m depth. The overall deformational pattern imaged in our data is consistent with the Wasatch fault migrating eastward through time and with the abandonment of earlier synextensional faults, as part of the evolution of an inferred 20-km-wide half-graben structure within Utah Valley. Finite-difference 2D modeling suggests the imaged subsurface basin geometry can cause fourfold variation in peak ground velocity over distances of 300 m.

Utah↗
USGS2007

Near-Surface Shear Wave Velocity Versus Depth Profiles, VS30, and NEHRP Classifications for 27 Sites in Puerto Rico

In 2004 and 2005 the Puerto Rico Seismic Network (PRSN), Puerto Rico Strong Motion Program (PRSMP) and the Geology Department at the University of Puerto Rico-Mayaguez (UPRM) collaborated with the U.S. Geological Survey to study near-surface shear-wave (Vs) and compressional-wave (Vp) velocities in and around major urban areas of Puerto Rico. Using noninvasive seismic refraction-reflection profiling techniques, we acquired velocities at 27 locations. Surveyed sites were predominantly selected on the premise that they were generally representative of near-surface materials associated with the primary geologic units located within the urbanized areas of Puerto Rico. Geologic units surveyed included Cretaceous intrusive and volcaniclastic bedrock, Tertiary sedimentary and volcanic units, and Quaternary unconsolidated eolian, fluvial, beach, and lagoon deposits. From the data we developed Vs and Vp depth versus velocity columns, calculated average Vs to 30-m depth (VS30), and derived NEHRP (National Earthquake Hazards Reduction Program) site classifications for all sites except one where results did not reach 30-m depth. The distribution of estimated NEHRP classes is as follows: three class 'E' (VS30 below 180 m/s), nine class 'D' (VS30 between 180 and 360 m/s), ten class 'C' (VS30 between 360 and 760 m/s), and four class 'B' (VS30 greater than 760 m/s). Results are being used to calibrate site response at seismograph stations and in the development of regional and local shakemap models for Puerto Rico.

Open-File Report↗
USGS2007

Seismic Hazard Maps for Seattle, Washington, Incorporating 3D Sedimentary Basin Effects, Nonlinear Site Response, and Rupture Directivity

This report presents probabilistic seismic hazard maps for Seattle, Washington, based on over 500 3D simulations of ground motions from scenario earthquakes. These maps include 3D sedimentary basin effects and rupture directivity. Nonlinear site response for soft-soil sites of fill and alluvium was also applied in the maps. The report describes the methodology for incorporating source and site dependent amplification factors into a probabilistic seismic hazard calculation. 3D simulations were conducted for the various earthquake sources that can affect Seattle: Seattle fault zone, Cascadia subduction zone, South Whidbey Island fault, and background shallow and deep earthquakes. The maps presented in this document used essentially the same set of faults and distributed-earthquake sources as in the 2002 national seismic hazard maps. The 3D velocity model utilized in the simulations was validated by modeling the amplitudes and waveforms of observed seismograms from five earthquakes in the region, including the 2001 M6.8 Nisqually earthquake. The probabilistic seismic hazard maps presented here depict 1 Hz response spectral accelerations with 10%, 5%, and 2% probabilities of exceedance in 50 years. The maps are based on determinations of seismic hazard for 7236 sites with a spacing of 280 m. The maps show that the most hazardous locations for this frequency band (around 1 Hz) are soft-soil sites (fill and alluvium) within the Seattle basin and along the inferred trace of the frontal fault of the Seattle fault zone. The next highest hazard is typically found for soft-soil sites in the Duwamish Valley south of the Seattle basin. In general, stiff-soil sites in the Seattle basin exhibit higher hazard than stiff-soil sites outside the basin. Sites with shallow bedrock outside the Seattle basin have the lowest estimated hazard for this frequency band.

Open-File Report↗
USGS2002

Shallow seismic imaging of folds above the Puente Hills blind-thrust fault, Los Angeles, California

High-resolution seismic reflection profiles image discrete folds in the shallow subsurface (<600 m) above two segments of the Puente Hills blind-thrust fault system, Los Angeles basin, California. The profiles demonstrate late Quaternary activity at the fault tip, precisely locate the axial surfaces of folds within the upper 100 m, and constrain the geometry and kinematics of recent folding. The Santa Fe Springs segment of the Puente Hills fault zone shows an upward-narrowing kink band with an active anticlinal axial surface, consistent with fault-bend folding above an active thrust ramp. The Coyote Hills segment shows an active synclinal axial surface that coincides with the base of a 9-m-high scarp, consistent with tip-line folding or the presence of a backthrust. The seismic profiles pinpoint targets for future geologic work to constrain slip rates and ages of past events on this important fault system.

California↗
USGS2002

Reconnaissance shallow seismic investigation of depth-to-bedrock and possible methane-bearing coalbeds, Galena, Alaska

A reconnaissance shallow seismic reflection/refraction investigation in and around the city of Galena, Alaska suggests that Tertiary and/or Cretaceous bedrock, and possible coalbeds within the Cretaceous, is at least as deep as 550 feet in the immediate vicinity of town. Rock could be deeper than 1000 feet under alternate interpretations. Reflections recorded in these data are believed to be from the sediment/bedrock interface. Analysis of these reflections and associated refractions indicates that this interface, interpreted at most of the six profile locations, has a high seismic velocity, possibly indicating non-sedimentary rock (e.g. volcanic or igneous).

Open-File Report↗
USGS2001

A test of a mechanical multi-impact shear-wave seismic source

We modified two gasoline-engine-powered earth tampers, commonly used as compressional-(P) wave seismic energy sources for shallow reflection studies, for use as shear(S)-wave energy sources. This new configuration, termed ?Hacker? (horizontal Wacker?), is evaluated as an alternative to the manual sledgehammer typically used in conjunction with a large timber held down by the front wheels of a vehicle. The Hacker maximizes the use of existing equipment by a quick changeover of bolt-on accessories as opposed to the handling of a separate source, and is intended to improve the depth of penetration of S-wave data by stacking hundreds of impacts over a two to three minute period. Records were made with a variety of configurations involving up to two Hackers simultaneously then compared to a reference record made with a sledgehammer. Preliminary results indicate moderate success by the higher amplitude S-waves recorded with the Hacker as compared to the hammer method. False triggers generated by the backswing of the Hacker add unwanted noise and we are currently working to modify the device to eliminate this effect. Correlation noise caused by insufficient randomness of the Hacker impact sequence is also a significant noise problem that we hope to reduce by improving the coupling of the Hacker to the timber so that the operator has more control over the impact sequence.

Open-File Report↗
USGS2000

High-resolution seismic reflection surveys and modeling across an area of high damage from the 1994 Northridge earthquake, Sherman Oaks, California

Approximately 3.6 km of P-wave seismic-reflection data were acquired along two orthogonal profiles in Sherman Oaks, California to determine whether shallow (less than 1-km depth) geologic structures contributed to the dramatic localized damage resulting from the 1994 Northridge earthquake. Both lines, one along Matilija Avenue and one along Milbank Street, crossed areas of both high and low damage. We believe these data reveal a geologic structure in the upper 600 m that contributed to the increased earthquake ground shaking in the high-damage areas south of and along the Los Angeles River. Of interest in these data is a reflection interpreted to be from bedrock that can be traced to the north along the Matilija Avenue profile. This reflecting interface, dipping northward at 15°–22°, may be an important impedance boundary because it is the lower boundary of a wedge of overlying low-velocity sediments. The wedge thins and terminates in the area where we interpret down-warped reflections as evidence of a shallow subbasin. The low-velocity subbasin sediments (V s of 200 m/sec V p of 500 m/sec) may be up to 150 m thick beneath the channelized Los Angeles River. The area across the subbasin experienced greater earthquake damage from possible geometric focusing effects. Three-dimensional basin effects may be responsible for the variable damage pattern, but from these seismic profiles it is not possible to determine the regional structural trends. Two-dimensional elastic and SH-mode finite-difference modeling of the imaged structural geometry along Matilija Avenue suggests that a peak horizontal-velocity amplification factor of two-and-over can be explained in the high-damage area above the shallow subbasin and sediment wedge. Amplification factors up to 5 were previously observed in aftershock data, at frequencies of 2 to 6 Hz. Amplification in the elastic simulation at the Santa Monica Mountains range-front on the southern end of the Matilija profile, with the geologic layering and geometry interpreted from the seismic data, is also consistent with aftershock observations.

Bulletin of the Seismological Society of America↗
USGS1995

Characterization of the Cottonwood Grove and Ridgely faults near Reelfoot Lake, Tennessee, from high-resolution seismic reflection data

In the winter of 1811-12, three of the largest historic earthquakes in the United States occurred near New Madrid, Missouri. Seismicity continues to the present day throughout a tightly clustered pattern of epicenters centered on the bootheel of Missouri, including parts of northeastern Arkansas, northwestern Tennessee, western Kentucky, and southern Illinois. In 1990, the New Madrid seismic zone/Central United States became the first seismically active region east of the Rocky Mountains to be designated a priority research area within the National Earthquake Hazards Reduction Program (NEHRP). This Professional Paper is a collection of papers, some published separately, presenting results of the newly intensified research program in this area. Major components of this research program include tectonic framework studies, seismicity and deformation monitoring and modeling, improved seismic hazard and risk assessments, and cooperative hazard mitigation studies.

Professional Paper↗