Geology topics

Edward F. Bugliosi

Publications and source records attributed to Edward F. Bugliosi.

12 recordsLinked to original sources

USGS2014

Hydrogeology and water quality of the stratified-drift aquifer in the Pony Hollow Creek Valley, Tompkins County, New York

The lithology, areal extent, and the water-table configuration in stratified-drift aquifers in the northern part of the Pony Hollow Creek valley in the Town of Newfield, New York, were mapped as part of an ongoing aquifer mapping program in Tompkins County. Surficial geologic and soil maps, well and test-boring records, light detection and ranging (lidar) data, water-level measurements, and passive-seismic surveys were used to map the aquifer geometry, construct geologic sections, and determine the depth to bedrock at selected locations throughout the valley. Additionally, water-quality samples were collected from selected streams and wells to characterize the quality of surface and groundwater in the study area. Sedimentary bedrock underlies the study area and is overlain by unstratified drift (till), stratified drift (glaciolacustrine and glaciofluvial deposits), and recent post glacial alluvium. The major type of unconsolidated, water-yielding material in the study area is stratified drift, which consists of glaciofluvial sand and gravel, and is present in sufficient amounts in most places to form an extensive unconfined aquifer throughout the study area, which is the source of water for most residents, farms, and businesses in the valleys. A map of the water table in the unconfined aquifer was constructed by using (1) measurements made between the mid-1960s through 2010, (2) control on the altitudes of perennial streams at 10-foot contour intervals from lidar data collected by Tompkins County, and (3) water surfaces of ponds and wetlands that are hydraulically connected to the unconfined aquifer. Water-table contours indicate that the direction of groundwater flow within the stratified-drift aquifer is predominantly from the valley walls toward the streams and ponds in the central part of the valley where groundwater then flows southwestward (down valley) toward the confluence with the Cayuta Creek valley. Locally, the direction of groundwater flow is radially away from groundwater mounds that have formed beneath upland tributaries that lose water where they flow on alluvial fans on the margins of the valley. In some places, groundwater that would normally flow toward streams is intercepted by pumping wells. Surface-water samples were collected in 2001 at four sites including Carter, Pony Hollow (two sites), and Chafee Creeks, and from six wells throughout the aquifer. Calcium dominates the cation composition and bicarbonate dominates the anion composition in groundwater and surface-water samples and none of the common inorganic constituents collected exceeded any Federal or State water-quality standards. Groundwater samples were collected from six wells all completed in the unconfined sand and gravel aquifer. Concentrations of calcium and magnesium dominated the ionic composition of the groundwater in all wells sampled. Nitrate, orthophosphate, and trace metals were detected in all groundwater samples, but none were more than U.S. Environmental Protection Agency or New York State Department of Health regulatory limits.

New York↗

USGS2013

Geohydrology, water quality, and simulation of groundwater flow in the stratified-drift aquifer system in Virgil Creek and Dryden Lake Valleys, Town of Dryden, Tompkins County, New York

In 2002, the U.S. Geological Survey, in cooperation with the Tompkins County Planning Department and the Town of Dryden, New York, began a study of the stratified-drift aquifer system in the Virgil Creek and Dryden Lake Valleys in the Town of Dryden, Tompkins County. The study provided geohydrologic data needed by the town and county to develop a strategy to manage and protect their water resources. In this study area, three extensive confined sand and gravel aquifers (the upper, middle, and lower confined aquifers) compose the stratified-drift aquifer system. The Dryden Lake Valley is a glaciated valley oriented parallel to the direction of ice movement. Erosion by ice extensively widened and deepened the valley, truncated bedrock hillsides, and formed a nearly straight, U-shaped bedrock trough. The maximum thickness of the valley fill in the central part of the valley is about 400 feet (ft). The Virgil Creek Valley in the east part of the study area underwent less severe erosion by ice than the Dryden Lake Valley, and hence, it has a bedrock floor that is several hundred feet higher in altitude than that in the Dryden Lake Valley. The sources and amounts of recharge were difficult to identify in most areas because the confined aquifers are overlain by confining units. However, in the vicinity of the Virgil Creek Dam, the upper confined aquifer crops out at land surface in the floodplain of a gorge eroded by Virgil Creek, and this is where the aquifer receives large amounts of recharge from precipitation that directly falls over the aquifer and from seepage losses from Virgil Creek. The results of streamflow measurements made in Virgil Creek where it flows through the gorge indicated that the stream lost 1.2 cubic feet per second (ft 3 /s) or 0.78 million gallons per day (Mgal/d) of water in the reach extending from 220 ft downstream from the dam to 1,200 ft upstream from the dam. In the southern part of the study area, large amounts of recharge also replenish the stratified-drift aquifers at the Valley Heads Moraine, which consists of heterogeneous sediments including coarse-grained outwash and kame sediments, as well as zones containing till with a fine-grained matrix. In the southern part of the study area, the confining units are thin and likely to be discontinuous in some places, resulting in windows of permeable sediment, which can more readily transmit recharge from precipitation and from tributaries that lose water as they flow over the valley floor. In contrast, in the northern part of the study area, the confining units are thick, continuous, and comprise homogeneous fine-grained sediments that more effectively confine the aquifers than in the southern part of the study area. Most groundwater in the northern part of the study area discharges to the Village of Dryden municipal production wells, to the outlet to Dryden Lake, to Virgil Creek, and as groundwater underflow that exits the northern boundary of the study area. Most northward-flowing groundwater in the southern part of the study area discharges to Dryden Lake, to the inlet to Dryden Lake, and to homeowner, nonmunicipal community (a mobile home community and several apartments), and commercial wells. Most of this pumped water is returned to the groundwater system via septic systems. Most southward-flowing groundwater in the southern part of the study area discharges to the headwaters of Owego Creek and to agricultural wells; some flow also exits the southern boundary of the study area as groundwater underflow. The largest user of groundwater in the study area is the Village of Dryden. Water use in the village has approximately tripled between the early 1970s when withdrawals ranged between 18 and 30 million gallons per year (Mgal/yr) and from 2000 through 2008 when withdrawals ranged between 75 and 85 Mgal/yr. The estimated groundwater use by homeowners, nonmunicipal communities, and small commercial facilities outside the area supplied by the Village of Dryden municipal wells is estimated to be about 18.4 Mgal/yr. Most of this pumped water is returned to the groundwater system via septic systems. For this investigation, an aquifer test was conducted at the Village of Dryden production well TM 981 (finished in the middle confined aquifer at a well depth of 72 ft) at the Jay Street pumping station during June 19–21, 2007. The aquifer test consisted of pumping production well TM 981 at 104 gallons per minute over a 24-hour period. The drawdown in well TM 981 at the end of 24 hours of pumping was 19.2 ft. Results of the aquifer-test analysis for a partially penetrating well in a confined aquifer indicated that the transmissivity was 1,560 feet squared per day, and the horizontal hydraulic conductivity was 87 feet per day, based on a saturated thickness of 18 ft. During 2003–5, 14 surface-water samples were collected at 8 sites, including Virgil Creek, Dryden Lake outlet, and several tributaries. During 2003 through 2009, eight groundwater samples were collected from eight wells, including three municipal production wells, two test wells, and three domestic wells. Calcium dominates the cation composition, and bicarbonate dominates the anion composition in most groundwater and surface-water samples. None of the common inorganic constituents collected exceeded any Federal or State water-quality standards. Results from a three-dimensional, finite-difference groundwater-flow model were used to compute a water budget and to estimate the areal extent of the zone of groundwater contribution to the Village of Dryden municipal production wells. The model-computed water budget indicated that the sources of recharge to the confined aquifer system are precipitation that falls directly on the valley-fill sediments (40 percent of total recharge), stream leakage (35.5 percent), seepage from wetlands and ponds (12 percent), unchanneled runoff and groundwater inflow from the uplands (8.5 percent), and groundwater underflow into the eastern end of the model area (4 percent). Most groundwater discharges to surface-water bodies, including Dryden Lake (33 percent), streams (33 percent), and wetlands and ponds (10 percent of the total). In addition, some groundwater discharges as underflow out of the southern and northern ends of the model area (15 percent), to simulated pumping wells (4.5 percent), and to drains that represent seepage from the bluffs exposed in the gorge in the vicinity of the Virgil Creek Dam (4.5 percent). The areal extents of the zones of groundwater contribution for Village of Dryden municipal production wells TM 202 (Lake Road pump station, finished in the upper confined aquifer) and TM 981 (Jay Street pump station, finished in the middle confined aquifer) are 0.5 square mile (mi 2 ) and 0.9 mi 2 , respectively. The areal extent of the zone of contribution to production well TM 202 extends 2.2 miles (mi) southeast into the Virgil Creek Valley, whereas production well TM 981 extends 3.8 mi south in the Dryden Lake Valley. The areal extent of the zone of contribution to production well TM1046 (South Street pump station) is 1.4 mi 2 and extends 2.4 mi into Dryden Lake Valley and 0.5 mi into Virgil Creek Valley.

New York↗

USGS2008

Geohydrology of the Unconsolidated Valley-Fill Aquifer in the Meads Creek Valley, Schuyler and Steuben Counties, New York

The Meads Creek valley encompasses 70 square miles of predominantly forested uplands in the upper Susquehanna River drainage basin. The valley, which was listed as a Priority Waterbody by the New York State Department of Environmental Conservation in 2004, is prone to periodic flooding, mostly in its downstream end, where development is occurring most rapidly. Hydraulic characteristics of the unconsolidated valley-fill aquifer were evaluated, and seepage rates in losing and gaining tributaries were calculated or estimated, in an effort to delineate the aquifer geometry and identify the factors that contribute to flooding. Results indicated that (1) Meads Creek gained about 61 cubic feet of flow per second (about 6.0 cubic feet per second per mile of stream channel) from ground-water discharge and inflow from tributaries in its 10.2-mile reach between the northernmost and southernmost measurement sites; (2) major tributaries in the northern part of the valley are not significant sources of recharge to the aquifer; and (3) major tributaries in the central and southern part of the valley provide recharge to the aquifer. The ground-water portion of streamflow in Meads Creek (excluding tributary inflow) was 11.3 cubic feet per second (ft3/s) in the central part of the valley and 17.2 ft3/s in the southern part - a total of 28.5 ft3/s. Ground-water levels were measured in 29 wells finished in unconfined deposits for construction of a potentiometric-surface map to depict directions of ground-water flow within the valley. In general, ground water flows from the edges of the valley toward Meads Creek and ultimately discharges to it. The horizontal hydraulic gradient for the entire 12-mile-long aquifer averages about 30 feet per mile, whereas the gradient in the southern fourth of the valley averages about half that - about 17 feet per mile. A water budget for the aquifer indicated that 28 percent of recharge was derived from precipitation that falls on the aquifer, 32 percent was from losing reaches of tributaries, 38 percent was unchanneled flow from hillsides that slope toward the valley (this estimate includes runoff and shallow ground-water inflow from till and bedrock), and the remaining 2 percent was from deep ground-water inflow from till and bedrock to the sides and bottom of the aquifer. Nearly all (94 percent) of the water discharged from the aquifer is equivalent to the streamflow gain in Meads Creek; the remaining 6 percent discharges as deep outflow to unconsolidated deposits in the Cohocton River valley. Several characteristics of the Meads Creek valley may contribute to flooding in the downstream area: (1) the southward decrease in the ground-water gradient impedes the ability of the aquifer to transmit water southward and can cause water levels to rise, (2) a high water table, typically only 5 to 10 feet below land surface, results in little storage capacity to absorb water from large storms, (3) a downstream narrowing of the valley impedes the southward flow of ground water and can cause water levels to rapidly rise during periods of prolonged or heavy precipitation, and (4) the upland slopes (till-covered bedrock) produce rapid runoff that recharges the aquifer. The combined effect of these conditions limits the ability of the aquifer to transmit sudden, large increases in recharge from precipitation and thereby provides a high potential for flooding in the southern third of the valley.

Scientific Investigations Report↗

USGS2007

Hydrogeology of Two Areas of the Tug Hill Glacial-Drift Aquifer, Oswego County, New York

Two water-production systems, one for the Village of Pulaski and the other for the Villages of Sandy Creek and Lacona in Oswego County, New York, withdraw water from the Tug Hill glacial-drift aquifer, a regional sand and gravel aquifer along the western flank of the Tug Hill Plateau, and provide the sole source of water for these villages. As a result of concerns about contamination of the aquifer, two studies were conducted during 2001 to 2004, one for each water-production system, to refine the understanding of ground-water flow surrounding these water-production systems. Also, these studies were conducted to determine the cause of the discrepancy between ground-water ages estimated from previously constructed numerical ground-water-flow models for the Pulaski and Sandy Creek/Lacona well fields and the apparent ground-water ages determined using concentrations of tritium and chlorofluorocarbons. The Village of Pulaski withdrew 650,000 gallons per day in 2000 from four shallow, large-diameter, dug wells finished in glaciolacustrine deposits consisting of sand with some gravelly lenses 3 miles east of the village. Four 2-inch diameter test wells were installed upgradient from each production well, hydraulic heads were measured, and water samples collected and analyzed for physical properties, inorganic constituents, nutrients, bacteria, tritium, dissolved gases, and chlorofluorocarbons. Recharge to the Tug Hill glacial-drift aquifer is from precipitation directly over the aquifer and from upland sources in the eastern part of the recharge area, including (1) unchannelized runoff from till and bedrock hills east of the aquifer, (2) seepage to the aquifer from streams that drain the Tug Hill Plateau, (3) ground-water inflow from the till and bedrock on the adjoining Tug Hill Plateau. Water-quality data collected from four piezometers near the production wells in November 2003 indicated that the water is a calcium-bicarbonate type with iron concentrations that slightly exceeded the U.S. Environmental Protection Agency?s Secondary Maximum Contaminant Level in three of the four samples. The relatively small concentrations of major ions and nutrients in the samples indicate that there is no contamination from septic-tank effluent and dissolved road salt in the ground water at the Village of Pulaski well field. Three of the four samples were analyzed for total coliform bacteria and Escherichia coli (E. coli), and only total coliform bacteria were detected in all three samples. E. coli was not detected in any samples. The Villages of Sandy Creek and Lacona use about 270,000 gallons of water per day for public consumption?alternating withdrawals from northern and southern well fields located in glaciolacustrine beach, glaciofluvial outwash, and alluvial inwash deposits consisting mostly of silty sand and gravel. Four test wells were drilled, hydraulic heads were measured, and water samples collected between 2001 and 2003 and analyzed for physical properties, inorganic constituents, nutrients, bacteria, tritium, dissolved gases, and chlorofluorocarbons. The aquifer in the Sandy Creek/Lacona area is highly susceptible to contamination because the aquifer (1) is unconfined, (2) is highly transmissive, (3) is thin (10 to 25 feet) and narrow (about 0.5 miles wide), and (4) has relatively short ground-water flowpaths from recharge to discharge areas (including wells). Additionally, drainage ditches east of the southern well field intercept westward-flowing ground water, which then is routed to an area just upgradient from the production wells where some of the water seeps back into the aquifer and is captured by these wells, effectively shortcircuiting the ground-water-flow system. Water-quality samples collected from three wells in the Sandy Creek/Lacona southern well field indicate that the ground water is a sodium-bicarbonate/sulfate type and of good quality; however, in one water sample, the sodium concentration of 6

Scientific Investigations Report↗

USGS1999

The Midwestern Basins and Arches regional aquifer system in parts of Indiana, Ohio, Michigan, and Illinois — Summary

The Midwestern Basins and Arches aquifer system is composed of surficial deposits of Pleistocene and Holocene age and of Silurian and Devonian age carbonate rock in parts of Indiana, Illinois, Michigan, and Ohio. The study area encompasses a complex of structural arches--the Cincinnati, Findlay, and Kankakee arches--and it is bounded on the east, north, and west by the Appalachian, Michigan, and Illinois basins, respectively. This report describes the hydrogeologic framework, hydrology, and geochemistry of the Midwestern Basins and Arches.

Illinois, Indiana, Michigan, Ohio↗

USGS1994

A selected bibliography of references on geology, hydrology, and geochemistry of the Midwestern Basins and Arches region; Ohio, Indiana, Michigan, and Illinois

This report contains selected references used for the Midwestern Basins and Arches Regional Aquifer System Analysis project of the U.S. Geological Survey. The project was begun in 1988 to study the geologic framework, hydrology, and geochemistry of the surficial and the Silurian and Devonian carbonate-rock aquifers in the Midwestern Basins and Arches Region. The area of data collection is 90,000 square miles and includes parts of Ohio, Indiana, Michigan, and Illinois. Geologic, hydrologic, and geochemical references that apply to the hydrogeology and geochemistry of the region were collected and are presented in this bibliography by State and by geologic, hydrologic, and geochemical categories for each State.

Open-File Report↗

USGS1988

Potential yields of wells in unconsolidated aquifers in upstate New York — Lower Hudson sheet

This map shows the location and potential well yields from unconsolidated aquifers in the lower-Hudson region at a 1:250 ,000 scale. It also delineates segments of aquifers that are heavily used by community water systems and designated by the New York State Department of Environmental Conservation as ' Primary water supply ' aquifers and cites published reports that give detailed information on each area. Most aquifers were deposited in low-lying areas such as valleys or plains during deglaciation of the region. Thick, permeable, well-sorted sand and gravel deposits generally yield large quantities of water, more than 100 gal/min. Thin sand, sand and gravel deposits, or thicker gravel units that have a large content of silt and fine sand, yield moderate amounts of water, 10 to 100 gal/min. Wells dug in till and those drilled in bedrock commonly yield less than 10 gal/min. (USGS)

New York↗

USGS1988

Potential yields of wells in unconsolidated aquifers in upstate New York — Hudson-Mohawk sheet

This map shows the location and potential well yields of unconsolidated aquifers in the Hudson-Mohawk region at a scale of 1:250,000. It also delineates segments of aquifers that are heavily used by community water systems and designated by the New York State Department of Environmental Conservation as ' Primary Water Supply ' aquifers, and cites published reports that give detailed information on each area. Most aquifers were deposited in low-lying areas such as valleys or plains during deglaciations of the region. Thick, permeable, well-sorted sand and gravel deposits generally yield large quantities of water, greater than 100 gal/min. Thin sand, sand and gravel deposits, or thicker gravel units that have a large content of silt and fine sand, yield moderate amounts of water, 10 to 100 gal/min. Wells dug in till and those drilled in bedrock commonly yield less than 10 gal/min.

New York↗

USGS1988

Potential yields of wells in unconsolidated aquifers in upstate New York — Adirondack sheet

This map shows the location and potential well yield from unconsolidated aquifers in the Adirondack region at a 1:250,000 scale. It also delineates segments of aquifers that are heavily used by community water systems and designated by the New York State Department of Environmental Conservation as ' Primary Water Supply ' aquifers and cites published reports that give detailed information on each area. Most aquifers were deposited in low-lying areas such as valleys or plains during deglaciation of the region. Thick, permeable, well-sorted sand and gravel deposits generally yield large quantities of water, greater than 100 gal/min. Thin sand, sand and gravel deposits, or thicker gravel units have a large content of silt and fine sand, yield moderate amounts of water, 10 to 100 gal/min. Wells dug in till and those drilled in bedrock commonly yield less than 10 gal/min. (USGS)

New York↗

USGS1987

Availability of ground water in the unconsolidated aquifers in the Mid-Hudson River Basin, New York

Protection of New York State 's aquifers has become an increasingly important issue among water resource managers at all levels of State and municipal government. Aquifer delineation is necessary as an initial phase in the effective management of the State 's groundwater resources. As part of an effort to delineate all major unconsolidated aquifers in New York, a cooperative study was conducted to compile a groundwater availability map that would complete the reconnaissance mapping of the mid-Hudson River basin at a scale of 1:250,000. This map delineates the principal unconsolidated aquifers in the mid-Hudson River basin area and the estimated potential yield of properly constructed wells completed in these aquifers. (Lantz-PTT)

Water-Resources Investigations Report↗

USGS1987

Ground-water availability from the unconsolidated deposits of the St. Lawrence River Basin, New York

Protection of New York State 's aquifers has become an increasingly important issue among water resource managers at all levels of State and Local government. Aquifer delineation is necessary as an initial phase in the effective management of the State 's groundwater resources. Many of New York 's productive aquifers consist of unconsolidated deposits. In an effort to obtain complete coverage of all the significant unconsolidated aquifers in New York, the U.S. Geological Survey and the New York State Department of Environmental Conservation began a cooperative study in 1985 to compile groundwater availability maps of each major river basin. This map delineates the unconsolidated aquifers that underlie the State 's northernmost eight counties and gives the estimated potential yield of properly constructed wells completed in these aquifers. Additional well locations and delineation of the aquifers were obtained through a well inventory conducted during the study. (Lantz-PTT)

Water-Resources Investigations Report↗

USGS1985

Hydrologic reconnaissance of the Chilkat River basin, southeast Alaska, with special reference to the bald eagle critical habitat at the Tsirku River alluvial fan

The Chilkat River basin in southeast Alaska is characterized by rugged, highly dissected mountains with steep-gradient streams, braided rivers in broad alluvium-filled valleys, and numerous glaciers. A wide seasonal range in temperature and strong orographic effects cause variations in the amount and distribution of precipitation, and thus in the resulting runoff and streamflow. Streamflow is lowest in winter, when precipitation at higher altitudes is stored as snow, and greatest in summer, when melting snow and glacier ice augment flow. Ground-water seeps and springs flowing from alluvial fans contribute to streamflow year round. A ground-water discharge zone of particular interest is that along the toe of the Tsirku River alluvial fan, 20 miles north of Haines. During winter, the relatively warm (4 to 6 degrees Celsius) ground water maintains open leads in a reach of the Chilkat River downstream from the fan. This ice-free reach provides favorable spawning habitat for a late run of chum and coho (silver) salmon, which in turn attracts the world's largest concentration of bald eagles (more than 3,000 birds). The principal source of recharge to the ground-water system in the fan is loss of water through the beds of the many distributary channels across the fan surface. Calculation of a water budget for the system for the period October 1982 through May 1983 indicates that ground-water discharge at the toe of the fan averages 640 cubic feet per second. Surface and ground waters are chemically similar, calcium bicarbonate types. All stream samples had dissolved-solids concentrations of less than 115 milligrams per liter; values for ground water were slightly greater. During high summer flows, the suspended-sediment concentrations of the glacially fed Chilkat, Tsirku, and Klehini Rivers ranged from 361 to 1,530 milligrams per liter (6,360 to 22,300 tons per day).

Alaska↗