Geology Reports⌕ Search

Geology topics

E. F. Hollyday

Publications and source records attributed to E. F. Hollyday.

15 recordsLinked to original sources
USGS2007

Dry Stream Reaches in Carbonate Terranes: Surface Indicators of Ground-Water Reservoirs

In areas where dry stream reaches occur, subsurface drainage successfully competes with surface drainage, and sheet-like dissolution openings have developed parallel to bedding creating the ground-water reservoir. Union Hollow in south-central Tennessee is the setting for a case study that illustrates the application of the dry stream reach technique. In this technique, dry stream reach identification is based on two types of readily acquired information: remotely sensed black and white infrared aerial photography; and surface reconnaissance of stream channel characteristics. Test drilling in Union Hollow subsequent to identification of the dry reach proved that a localized ground-water reservoir was present.

Water Resources Bulletin↗
USGS2000

Hydrogeology and hydrogeologic terranes of the Blue Ridge and Piedmont Physiographic Provinces in the eastern United States

Severe and prolonged droughts between 1961 and 1988, combined with increased demands for freshwater supplies in the United States, have resulted in a critical need to assess the potential for development of ground- and surface-water supplies. Rapid industrial growth and urban expansion have caused existing freshwater supplies to be used at or near maximum capacity. Begun in 1978, the Regional Aquifer-System Analysis (RASA) Program of the U.S. Geological Survey (USGS) is a systematic effort to study a number of the Nation's most important aquifer systems, which, in aggregate, underlie much of the country and represent an important component of the Nation's total water supply. The broad objective for each of the 28 studies in the program is to assemble geologic, hydrologic, and geochemical information, to analyze and develop an understanding of the system, and to develop predictive capabilities that will contribute to the effective management of the system. In 1988, as part of the RASA Program, the USGS began a 6-year study of the ground-water resources of parts of 11 States in the Eastern United States (Swain and others, 1991). The study was designated the Appalachian Valley and Piedmont Regional Aquifer-System Analysis (APRASA). The APRASA team investigated ground-water resources primarily in the unglaciated part of the Valley and Ridge, the Blue Ridge, the New England, and the Piedmont Physiographic Provinces (fig. 1). For the purposes of this report, the small area in the New England Physiographic Province that is within the study area in New Jersey and Pennsylvania was considered part of the Piedmont Physiographic Province. The results of the APRASA are contained in about 50 reports and abstracts, including reports on simulation of ground-water flow in three type areas, this atlas, and chapters in Professional Paper 1422. These chapters include the summary (Chapter A), descriptions of recharge rates and surface- and ground-water relations (Chapter B), hydrogeologic terranes in the Valley and Ridge Physiographic Province (Chapter C), and ground-water geochemistry (Chapter D). The purposes of this atlas are to summarize the hydrogeology, to describe an analysis of maps and well records, and to present a classification and map of the hydrogeologic terranes of the Blue Ridge and Piedmont Physiographic Provinces within the APRASA study area. Hydrogeologic terranes are defined for this atlas as regionally mappable areas characterized by similar water-yielding properties of a grouping of selected rock types. The hydrogeologic terranes represent areas of distinct hydrologic character. The terranes are intended to help water users locate and develop adequate water supplies and to help hydrologists interpret the regional hydrogeology. Previous investigations provide maps and descriptions of the geologic units, describe the local quantity and quality of ground water within these units, and establish the statistical methods for comparing the water-yielding properties of these units. State geologic maps show the distribution of geologic units at a scale of 1:500,000 for Alabama (Osborne and others, 1989), Georgia (Lawton and others, 1976), North Carolina (Brown and Parker, 1985), and Virginia (Calver and Hobbs, 1963). State maps show geologic units at a scale of 1:250,000 for Maryland (Cleaves and others, 1968), New Jersey (Lewis and Kummel, 1912), Pennsylvania (Berg and others, 1980), South Carolina (Overstreet and Bell, 1965), Tennessee (Hardeman, 1966), and West Virginia (Cardwell and others, 1968). Quadrangle geologic maps show geologic units at a scale of 1:24,000 for parts of Delaware within the APRASA area (Woodruff and Thompson, 1972, 1975). Many reports have been published describing the groundwater resources of a county, parts of a county, multi-county areas, or river basins. The statistical methods used in this atlas are based largely on those used by Helsel and Hirsch (1992) and by Knopman (1990, p. 7-9). In her analysis of well records in the USGS Ground-Water Site Inventory (GWSI) data base, Knopman (1990) ranked factors that must be taken into account when assessing the water-yielding potential of the rocks in the Valley and Ridge, the Blue Ridge, and the Piedmont Physiographic Provinces in Pennsylvania. Readers are referred to Helsel and Hirsch (1992) and Knopman (1990) for details regarding statistical methods.

Alabama, Delaware, Georgia, Maryland, New Jersey, ↗
USGS1996

Hydrogeologic terranes and potential yield of water to wells in the Valley and Ridge Physiographic Province in Maryland, New Jersey, and Pennsylvania

The hydrogeologic framework of the Valley and Ridge Physiographic Province in Maryland, New Jersey, and Pennsylvania was analyzed by the U.S. Geological Survey as part of the Appalachian Valleys— Piedmont Regional Aquifer-System Analysis project. Local differences in lithology, structure, and weathering result in large variation in the water-yielding properties of the rock that underlies the area, Selected rock types, however, can account for a substantial part of this variation because of the unique way in which these rock types deform and weather to produce secondary openings. On the basis of the relations among rock type and water-yielding openings and properties, the regolith and consolidated rock were classified and mapped as five hydrogeologic terranes—alluvium, dolomite. limestone, argillaceous carbonate rock, and siliciclastic rock. Specific-capacity data for homogeneous data sets, which consist of all wells that have the same characteristics in regard to casing diameter, primary use of the water, and topographic setting, revealed significant differences in water-yielding properties among the five hydrogeologic terranes. According to results of Tukey tests at a probability (alpha level) of 0.10, eight out of ten pairs of hydrogeologic terranes had significantly different median specific-capacity values. Estimates of potential yields to public- and industrial-supply wells were calculated from specific-capacity data for most-productive wells—wells with casing diameter of 7 inches or more, used primarily for public or industrial supply, and in a valley—using median drawdowns for each hydrogeologic terrane, Estimated interquartile ranges in potential yields to most-productive wells in the hydrogeologic terranes, in gallons per minute, were 170 to 600 in alluvium; 280 to 1,700 in dolomite, 80 to 520 in limestone; fish to 550 in argillaceous carbonate rock; and 60 to 24s) in siliciclustic rock.

Maryland, New Jersey, Pennsylvania↗
USGS1996

Hydrogeologic terranes and potential yield of water to wells in the Valley and Ridge Physiographic Province in the eastern and southeastern United States

The Valley and Ridge Physiographic Province is underlain by deformed sedimentary rock of Paleozoic age including dolomite, limestone, shale, and sandstone. Regolith (soil, sediment, and weathered rock) covers the Paleozoic rock throughout most of the province. Local differences in lithology, structure, and weathering can result in four orders of magnitude variation in the water-yielding properties of the geologic units that underlie the area. Selected rock types, however, can account for a substantial part of this variation because of the unique way in which these dense, consolidated sedimentary rock types deform and weather to produce secondary openings. On the basis of relations among rock type, water-yielding openings, and water-yielding properties (as indicated by specific capacity), the regolith and consolidated rock were classified and mapped as five hydrogeologic terranes alluvium, dolomite, limestone, argillaceous carbonate rock, and siliciclastic rock. The hydrogeologic terranes are named after the predominant outcrop lithology within them. The western toe of the Blue Ridge Mountains is classified as a subdivision of the dolomite hydrogeologic terrane that may produce yields of water in excess of 1,000 gallons per minute (gal/min) to public and industrial supply wells. Specific-capacity data for homogeneous data sets, which consist of all wells that have the same characteristics in regard to casing diameter, primary use of the water, and topographic setting, revealed significant differences in water-yielding properties among the five hydrogeologic terranes. According to results of Tukey statistical tests at a probability (alpha level) of 0.05, 8 out of 10 pairs of hydrogeologic terranes (for example, alluvium/limestone) had significantly different median specific-capacity values. The median value for public and industrial supply wells in the western toe is three times greater than the value for comparable wells in the dolomite hydrogeologic terrane elsewhere. Estimates of potential yields to public and industrial supply wells were calculated from specific-capacity data for most-productive wells, which have casing diameter of 7 in. or more, discharge water primarily for public or industrial supply, and are in a valley. Median constant drawdowns, calculated from reported drawdowns, were assumed to be between 10 and 90 ft for wells completed in each of the five hydrogeologic terranes, and well-entrance losses were assumed to be negligible. Estimated interquartile ranges in potential yields to 412 mostproductive wells in the five hydrogeologic terranes were 170 to 580 gal/min, alluvium; 210 to 1,400 gal/min, dolomite; 80 to 720 gal/min, limestone; 65 to 850 gal/min, argillaceous carbonate rock; and 70 to 280 gal/min, siliciclastic rock.

Alabama, Georgia, Maryland, New Jersey, Pennsylvan↗
USGS1995

Water-quality, discharge, and biologic data for streams and springs in the Highland Rim Escarpment of southeastern Bedford County, Tennessee

From November 1994 through April 1995, streams and springs in 9 drainage basins were observed and sampled at 176 sites to obtain information on environmental quality near the Quail Hollow landfill, Bedford County, Tennessee. Reconnaissance data were collected to establish a regional pattern. Water samples from 26 seepage sites were analyzed to determine water-quality conditions. During the reconnaissance, conductivity ranged regionally from 17 to 617 microsiemens per centimeter. The greatest biologic diversity was in Bennett Branch, followed by Daniel Hollow, Prince, Powell and Renegar, County Line, and Anthony Branches, Hurricane Creek, and Anderton Branch, respectively. In general, conductivity was less than 50 microsiemens per centimeter at and upstream of the Chattanooga Shale but increased downstream to between 200 and 300 microsiemens per centimeter. Of the constituents and properties analyzed, only pH and four metals at six sites had values that were not within the limits set by the State of Tennessee for drinking water. Chloride and dissolved manganese concentrations were highest for a spring and a seep adjacent to the landfill. Scans indicated the presence of about 37 unidentified organic compounds at these same two sites.

Tennessee↗
USGS1990

Large springs in the Valley and Ridge Province in Tennessee

Approximately 2,700 miscellaneous discharge measurements for 171 large springs in 28 counties of East Tennessee, predominantly within the Valley and Ridge physiographic province, were analyzed statistically and results tabulated to summarize data useful to the Appalachian Valleys-Piedmont Regional Aquifer System Analysis study. The number of measurements at each spring ranged from 1 to 65. Information from each spring includes station numbers, latitude, longitude, spring name and where data are sufficient, an estimate of the mean discharge and the discharge exceeded by 75%, 50%, and 25% of the miscellaneous measurements. Data are referenced to locations on a 1:1,000 ,000-scale map. The highest mean spring discharge was 32.2 cu ft/sec (14,5000 gallons/min).

Tennessee↗
USGS1983

Use of digital land-cover data from the Landsat satellite in estimating streamflow characteristics in the Cumberland Plateau of Tennessee

Characteristics of Streamflow at ungaged sites in coal-mining areas of the Cumberland Plateau may be estimated with regression equations that relate streamflow characteristics to the physiographic and climatic characteristics of the corresponding drainage basins. An experiment was performed to compare the accuracy of equations using basin characteristics derived from maps and climatological records (control group equations) with the accuracy of equations using basin characteristics derived from digital processing of Landsat spectral data as well as maps and climatological records (experimental group equations). Results of this experiment show that (with the exception of low flows and four of six annual peak logarithms) drainage area can explain more than 90 percent of the variance in all streamflow characteristics in both groups of equations. Seventeen of 39 experimental group equations that have two basin characteristics each are different from the corresponding control group equations. Five of the 17 differing experimental group equations have no counterpart in the control group because of lack of significance in control group basin characteristics, seven are slightly more accurate, and five are not measurably different in accuracy. When the equations in both groups are arranged into six flow categories, there is no substantial difference in accuracy between equations using basin characteristics derived from maps and climatological records (control group) and equations using basin characteristics derived from Landsat tapes as well as maps and climatological records (experimental group) for this particular study area, the Cumberland Plateau of Tennessee.

Tennessee↗
USGS1983

Ground water in carbonate rocks and regolith in the Fairview area, Tennessee

Fourteen test wells drilled in the Fairview area, Tennessee, produce from 3 to 100 gallons per minute and have an average yield of 32 gallons per minute, measured while blowing water from the wells with compressed air. In comparison, the average yield of supply wells reported by drillers is 13 gallons per minute. Specific capacities for three of the test wells ranged from 0.3 to 0.6 gallons per minute per foot of drawdown after 8 hours of pumping at 20 to 47 gallons per minute. Two test wells had specific capacities of 1.1 and 0.4 gallons per foot of drawdown after 72 hours of pumping at 55 and 43 gallons per minute. The mineral content of ground water increases greatly below a gypsum horizon approximately 100 feet below the top of the Fort Payne Formation. Ground water above the gypsum horizon, however, meets the standards for finished drinking water. (USGS)

Water-Resources Investigations Report↗
USGS1979

Ground-water availability in carbonate rocks of the Dandridge area, Jefferson County, Tennessee

Groundwater in Jefferson County, Tenn., occurs in solution openings that follow bedding planes and strike joints in the dense limestone and dolomite. Recharge beginning at topographic highs in the northwest moves across strike to lows in the southeast; it is intercepted and collected by high permeability beds in the middle of the Knox Group and is routed along strike to discharge at large springs. Exploratory wells were drilled at two sites to test this concept of the flow system. Three wells at Moore Spring site in the recharge area penetrated only mud and solid rock. Four wells at Riley Spring site in the discharge area each penetrated at least five water-bearing openings that gave these wells an average production of 93 gallons per minute and a maximum of 180 gallons per minute. (USGS)

Open-File Report↗
USGS1976

Mapping and measuring land-cover characteristics of New River Basin, Tennessee, using Landsat digital tapes

Land-cover information is needed to select subbasins within the New River basin, Tennessee, for the study of hydrologic processes and also is needed to transfer study results to other sites affected by coal mining. It was believed that data recorded by the first Earth Resources Technology Satellite (Landsat-1) could be processed to yield the needed land-cover information. This study demonstrates that digital computer processing of the spectral information contained in each picture element (pixel) of 1.1 acres (4,500 m2) can produce maps and tables of the areal extent of selected land-cover categories. The distribution of water, rock, agricultural areas, evergreens, bare earth, hardwoods, and uncategorized areas, is portrayed on a map of the entire New River basin (1:62,500 scale) and on 15 quadrangles (1:24,000 scale). Although some categories are a mixture of land-cover types, they portray the predominant component named. Tables quantify the area of each category and indicate that agriculture covers 5 percent of the basin, evergreens cover 7 percent, bare earth covers 6 percent, three categories of hardwoods cover 81 percent, and water, rock, and uncategorized areas each cover less than 1 percent of the basin.

Tennessee↗