Geology topics

Dianne L. Brien

Publications and source records attributed to Dianne L. Brien.

18 recordsLinked to original sources

USGS2026

Map depicting locations susceptible to landslide hazards triggered by prolonged intense rainfall, Utuado Municipio, Puerto Rico

Introduction Landslides commonly occur in Puerto Rico during or soon after rainstorms with prolonged intense rainfall. Rainfall-triggered landslides present significant hazards to the built environment and human safety (for example, Jibson, 1986; Larsen and Torres Sanchez, 1992; Bessette-Kirton and others, 2019a). These hazards were illustrated during September 2017 (Hughes and others, 2019) when Hurricane María triggered more than 70,000 landslides across Puerto Rico (fig. 1), causing loss of life and widespread destruction (figs. 2–4). In Utuado Municipio, about 18,000 landslides were observed after Hurricane María (Hughes and others, 2019). Most intense rainfall-triggered landslides in Puerto Rico occur in soil overlying bedrock and travel downslope from where they initiate (for example, Jibson, 1986; Bessette-Kirton and others, 2019a, 2020). Hazards to human life and infrastructure can differ substantially between where landslides initiate and where they travel. At landslide initiation locations, the ground breaks up (fails) as it moves downslope, removing support for buildings, roadways, and other structures located upon the landslides (fig. 3A, B). This ground failure often causes structures to collapse and suffer severe damage or complete destruction, rendering building occupants at extreme risk. Roadways and other vital infrastructure, such as water, power, and communication lines, are often severed. During intense rainfall events, landslide initiation and movement downslope can occur in seconds to hours. Downslope from where they initiate, landslides in Puerto Rico often move very rapidly (faster than a person can walk or run) and can impact and destroy or fill structures with mud and debris (fig. 4) as well as bury roadways (fig. 3A, C). Moving landslides present extreme hazards to human safety; some fatalities during Hurricane María resulted from mud and debris that flowed through windows and doors of a home and buried occupants. Many landslides in Puerto Rico become fast-moving liquefied masses (debris flows), which are especially common in channels where they can quickly travel kilometers downstream. Multiple debris flows may occur in a channel during a single rainstorm (some channels experienced more than 50 debris flows during Hurricane María; Bessette-Kirton and others [2020] ). This hazard map separately depicts locations and the relative likelihood of where landslides may initiate, where they may move downslope, and where channelized debris flows may travel during or soon after intense rainfall like that during Hurricane María. An estimated average of 399 millimeters of rainfall fell across Utuado during September 19–21, 2017 (Ramos-Scharrón and Arima, 2019). Lower rainfall amounts, durations, and intensities also trigger landsliding in Puerto Rico, although landslides and debris flows become more numerous as rainfall intensities, durations, and cumulative amounts increase. The map does not show potential landslide locations in the karst terrain of northern Utuado (Bawiec, 1999) because Hurricane María-induced landslides were very sparse in this region (Hughes and others, 2019; Baxstrom and others, 2021a), even though rainfall amounts were similar to those in other parts of Utuado. Based on data from Hughes and others (2019), landslides were about 10 times more likely to occur outside of the karst terrane than within it, and our preliminary analyses indicated relatively low susceptibility to rainfall-induced landslide hazards within the karst. Landslide-prone soils appear to be poorly developed on the very steep slopes present in the karst region, where weathering by dissolution appears to dominate.

Puerto Rico, Utuado Municipio↗

USGS2026

Map depicting locations susceptible to landslide hazards triggered by prolonged intense rainfall, Naranjito Municipio, Puerto Rico

Introduction Landslides commonly occur in Puerto Rico during or soon after rainstorms with prolonged intense rainfall. Rainfall-triggered landslides present significant hazards to the built environment and human safety (for example, Jibson, 1986; Larsen and Torres Sanchez, 1992; Bessette-Kirton and others, 2019a). These hazards were illustrated during September 2017 (Hughes and others, 2019), when Hurricane María triggered more than 70,000 landslides across Puerto Rico (fig. 1), causing loss of life and widespread destruction (figs. 2–4). In Naranjito Municipio, about 2,000 landslides were observed after Hurricane María (Hughes and others, 2019). Most intense-rainfall-triggered landslides in Puerto Rico occur in soil overlying bedrock and travel downslope from where they initiated (for example, Jibson, 1986; Bessette-Kirton and others, 2019a; 2020). Hazards to human life and infrastructure can differ substantially between where landslides initiate and where they travel. At landslide initiation locations, the ground breaks up (fails) as it moves downslope, removing support for buildings, roadways, and other structures located upon the landslides (figs. 3B, 4A, B). This ground failure often causes structures to collapse and suffer severe damage or complete destruction, rendering building occupants at extreme risk. Roadways and other vital infrastructure, such as water, power, and communication lines are often severed. During intense rainfall events, landslide initiation and movement downslope can occur in seconds to hours. Downslope from where they initiate, landslides in Puerto Rico often move, or runout, very rapidly (faster than a person can walk or run) and can impact and destroy or fill structures with mud and debris (figs. 3A, 4A, C) as well as bury roadways (fig. 4A). Moving landslides present extreme hazards to human safety; some fatalities during Hurricane María resulted from mud and debris that flowed through windows and doors of a home and buried occupants. Many landslides in Puerto Rico become fast-moving debris flows, which are especially common in channels where they can quickly travel kilometers downstream. Multiple debris flows may occur in a channel during a single rainstorm (some channels experienced more than 50 debris flows during Hurricane María; Bessette-Kirton and others, 2020). This map separately depicts locations and the relative likelihood of where landslides may initiate, where they may move downslope, and where channelized debris flows may travel during or soon after intense rainfall like that during Hurricane María. An estimated average of 529 millimeters of rainfall fell across Naranjito during September 19–21, 2017 (Ramos-Scharrón and Arima, 2019). Lower rainfall amounts, durations, and intensities also trigger landsliding in Puerto Rico, although landslides and debris flows become more numerous as rainfall intensities, durations, and cumulative amounts increase.

Naranjito Municipio, Puerto Rico↗

USGS2026

Map depicting locations susceptible to landslide hazards triggered by prolonged intense rainfall, Lares Municipio, Puerto Rico

Introduction Landslides commonly occur in Puerto Rico during or soon after rainstorms with prolonged intense rainfall. Rainfall-triggered landslides present significant hazards to the built environment and human safety (for example, Jibson, 1986; Larsen and Torres Sanchez, 1992; Bessette-Kirton and others, 2019a). These hazards were illustrated during September 2017 (Hughes and others, 2019), when Hurricane María triggered more than 70,000 landslides across Puerto Rico (fig. 1), causing loss of life and widespread destruction (figs. 2 and 3). In Lares Municipio, about 3,500 landslides were observed after Hurricane María (Hughes and others, 2019). Most intense-rainfall-triggered landslides in Puerto Rico occur in soil overlying bedrock and travel downslope from where they initiated (for example, Jibson, 1986; Bessette-Kirton and others, 2019a; 2020). Hazards to human life and infrastructure can differ substantially between where landslides initiate and where they travel. At landslide initiation locations, the ground breaks up (fails) as it moves downslope, removing support for buildings, roadways, and other structures located upon the landslides (figs. 2, 3A, B). This ground failure often causes structures to collapse and suffer severe damage or complete destruction, rendering building occupants at extreme risk. Roadways and other vital infrastructure, such as water, power, and communication lines are often severed. During intense rainfall events, landslide initiation and movement downslope can occur in seconds to hours. Downslope from where they initiate, landslides in Puerto Rico often move, or runout, very rapidly (faster than a person can walk or run) and can impact and destroy or fill structures with mud and debris (figs. 3A, C) as well as bury roadways (fig. 3A). Moving landslides present extreme hazards to human safety; some fatalities during Hurricane María resulted from mud and debris that flowed through windows and doors of a home and buried occupants. Many landslides in Puerto Rico become fast-moving debris flows, which are especially common in channels where they can quickly travel kilometers downstream. Multiple debris flows may occur in a channel during a single rainstorm (some channels experienced more than 50 debris flows during Hurricane María; Bessette-Kirton and others, 2020). This map separately depicts locations and the relative likelihood of where landslides may initiate, where they may move downslope, and where channelized debris flows may travel during or soon after intense rainfall like that during Hurricane María. An estimated average of 256 millimeters of rainfall fell across Lares during September 19–21, 2017 (Ramos-Scharrón and Arima, 2019). Lower rainfall amounts, durations, and intensities also trigger landsliding in Puerto Rico, although landslides and debris flows become more numerous as rainfall intensities, durations, and cumulative amounts increase. The map does not show potential landslide locations in the karst terrain of northern Lares (Bawiec, 1999) because Hurricane María-induced landslides were very sparse in this region (Hughes and others, 2019; Baxstrom and others, 2021a), even though rainfall amounts were similar to those in other parts of Lares. Based on data from Hughes and others (2019), landslides were about ten times more likely to occur outside of the karst terrane than within it, and our preliminary analyses indicate relatively low susceptibility to rainfall-induced landslide hazards within the karst. Landslide-prone soils appear to be poorly developed on the very steep slopes present in the karst region, where weathering by dissolution appears to dominate.

Lares Municipio, Puerto Rico↗

USGS2026

Assessment of extreme subsurface hydrologic conditions captured during atmospheric river storms in the San Francisco Bay area (California, USA) with applications to shallow landslide early warning

An increase in soil pore water pressure is the typical trigger for the majority of landslides caused by rainfall. Atmospheric river storms, common to the west coast of North America during the winter season, can deliver landslide triggering rainfall resulting in severe impacts to coastal communities. Using a network of hydrologic monitoring stations situated within landslide-prone terrain in the San Francisco Bay area of California (USA), we assess the meteorologic conditions and resulting hydrologic and landslide response resulting from eight consecutive storm events that caused thousands of shallow landslides during the winter of 2022–2023. We find disparate hydrological responses and resultant degrees of observed landsliding ranging from < 1 landslide/km2 to 18 landslides/km2 at the monitoring sites that reflect the interplay and differences between rainfall delivery, subsurface hydrological characteristics, and geotechnical properties at each site. Antecedent soil moisture from both early season rainfall and the first storm in the sequence played a critical role in setting up some hillslopes for failure. Subsequent storms then generated elevated pore water pressures for several hours with associated landsliding. However, we find that the occurrence of widespread landsliding required not only sufficient pore water pressure magnitude in susceptible hillslopes, but also full and prolonged effective soil saturation throughout hillslope profiles. Landslides may still occur at lower values and durations of effective saturation but are likely to be less extensive regionally. We present these findings within the context of research directions and improvements to landslide early warning systems first suggested by researchers 40 years ago.

California↗

USGS2026

From start to stop: Simple methods for mapping susceptibility to landslide runout and debris-flow inundation

Landslide runout and debris-flow inundation can disrupt areas well beyond their initial sources, causing widespread damage and extensive fatalities. Understanding where they start and how far they might travel is essential in many locations worldwide. However, most landslide susceptibility maps focus on initiation areas and fail to incorporate runout areas. Furthermore, hazards vary greatly with the degree of landslide mobility, and debris flows can grow as they travel beyond their initial source. Here, we use the USGS Grfin Tools software suite to map susceptible areas from start to stop in the Federated States of Micronesia where landslide and debris-flows runout onto gentle ground is a deadly threat. The DEM-based models in Grfin Tools use simple, empirical, and well-documented approaches that require minimal parameters and, thus, can be used in areas that lack detailed physical properties. We illustrate methods to estimate the required parameters using direct landslide observations, and we suggest alternate methods if direct observations are absent. Our simple parameter estimations in the Federated States of Micronesia successfully predict areas that match past landslide runout and debris-flow inundation, as well as zones with no inundation. In addition to creating preliminary regional assessments, Grfin Tools can be used for comparing multiple scenarios and/or identifying areas for further investigations.

Chuuk, Kosrae, Pohnpei↗

USGS2025

Topographic controls on landslide mobility: Modeling hurricane-induced landslide runout and debris-flow inundation in Puerto Rico

In 2017, Hurricane Maria triggered more than 70 000 landslides in Puerto Rico. After initiation, these predominantly shallow landslides were mobilized to varying extents – some landslides only traveled partway downslope, whereas others reached drainage channels and were mobilized into long-traveled debris flows that could severely impact roads and infrastructure. Thus, forecasting potential landslide runout and inundation zones is critical for estimating landslide and debris-flow hazards. Here we conduct an in-depth topographic analysis of landslide-affected areas from nine study areas and apply a linked modeling technique to estimate locations susceptible to varying degrees of landslide runout in the Lares, Utuado, and Naranjito municipalities. We find that the longest runout lengths are observed on high-relief escarpments, although highly mobile long-runout debris flows also occurred in lower-relief dissected uplands. These topographic differences indicate that landslides that are initiated under similar conditions and possess equal potential to be mobilized as debris flows may not travel the same distances or affect the same areal extent. Our modeling approach allows the local topography to automatically control the implementation of two runout methods: (1) H/L runout zones are assigned directly downslope of landslide source zones, and (2) debris-flow inundation zones are estimated in the presence of a channel network. Debris-flow volumes are calculated as a function of area-integrated growth factors, estimated as a function of the upstream areas susceptible to shallow landslides. Applying our empirical modeling scheme over an area of 560 km 2 , our results highlight the efficacy of our methods for the assessment of the potential for landslide runout and debris-flow inundation over diverse terrains with varied susceptibility.

Puerto Rico↗

USGS2025

Grfin Tools—User guide and methods for modeling landslide runout and debris-flow growth and inundation

The software package, Grfin Tools, can estimate potential runout from landslides or inundation from geophysical mass flows such as debris flows, lahars from volcanoes, and rock avalanches within a digital elevation model (DEM). Grfin is an acronym of gr owth + f low + in undation. The tools within this package apply simple, well-tested, empirical models of runout that are computationally efficient and require minimal parameters. These tools can be used individually (for example, to estimate debris-flow inundation) or in combination to represent a more complete series of linked processes, from landslide source areas, to unchannelized transport, to channelized flows. Grfin Tools can rapidly assess potential runout and inundation over large areas and the results are readily visualized in a geographic information system. Tools for assessing areas affected by runout and flow inundation include a height-to-length ( H / L ) ratio, angle-of-reach approach for estimating open-slope, unchannelized landslide runout, and volume-area scaling relations for assessing flow inundation in channels. Potential landslide areas that constitute the sources of runout or inundation can be delineated with topographic features, such as slope and (or) curvature, derived by the software package, or by employing potential sources derived from other landslide susceptibility models. Grfin Tools also has the capability to assess inundation from flows that grow volumetrically downstream. This is a vital feature, as larger flows commonly result in longer runout and larger inundation. The software uses empirically derived growth factors applied over upslope contributing source areas or upstream channel lengths to integrate the effects of various growth processes, such as channel entrainment, streambank failures, adjacent landslides, and hillslope erosion. Inundation follows a drainage network defined with a separate tool that uses topographic curvature to identify channel initiation locations. This document includes information on using Grfin Tools, the basis and methods underlying the tools and models, detailed descriptions of the software input and output files, and tips for handling special conditions such as roads and large water bodies. Multiple detailed examples illustrating different applications are also presented. Grfin Tools relies on the freely available TauDEM software package (Tarboton, 2005). The Grfin Tools software release is available from Cronkite-Ratcliff and others (2025).

Techniques and Methods↗

USGS2024

Assessing locations susceptible to shallow landslide initiation during prolonged intense rainfall in the Lares, Utuado, and Naranjito municipalities of Puerto Rico

Hurricane Maria induced about 70 000 landslides throughout Puerto Rico, USA, including thousands each in three municipalities situated in Puerto Rico's rugged Cordillera Central range. By combining a nonlinear soil-depth model, presumed wettest-case pore pressures, and quasi-three-dimensional (3D) slope-stability analysis, we developed a landslide susceptibility map that has very good performance and continuous susceptibility zones having smooth, buffered boundaries. Our landslide susceptibility map enables assessment of potential ground-failure locations and their use as landslide sources in a companion assessment of inundation and debris-flow runout. The quasi-3D factor of safety, F 3 , showed strong inverse correlation to landslide density (high density at low F 3 ). Area under the curve (AUC) of true positive rate (TPR) versus false positive rate (FPR) indicated success of F 3 in identifying head-scarp points (AUC = 0.84) and source-area polygons (0.85 ≤ AUC ≤ 0.88). The susceptibility zones enclose specific percentages of observed landslides. Thus, zone boundaries use successive F 3 levels for increasing TPR of landslide head-scarp points, with zones bounded by F 3 at TPR = 0.75, very high; F 3 at TPR = 0.90, high; and the remainder moderate to low. The very high susceptibility zone, with 118 landslides km −2 , covered 23 % of the three municipalities. The high zone (51 landslides km −2 ) covered another 10 %.

Puerto Rice↗

USGS2024

Investigating the atmospheric conditions associated with impactful shallow landslides in California (USA)

Shallow landslides are often triggered during rainfall events, which can increase subsurface soil water pressure and destabilize hillslopes. The likelihood of regional shallow landslide initiation is often assessed through a comparison of rainfall intensity and duration to pre-established thresholds. While informative for landslide warning, this exclusive focus on rainfall exceeding thresholds does not consider the meteorological conditions producing the rainfall. Here, we ask the question, are there common meteorological characteristics that lead to landslide-triggering precipitation? We develop a catalog of 18 post-1995 widespread, impactful shallow landslide events occurring within 13 storms across California, USA, where initiation time could be constrained to a ≤6-h window. We examine storm characteristics during the landslide initiation window using atmospheric reanalysis products, radar observations, and quantitative precipitation estimates. We find that, while there are some common atmospheric characteristics across landslide events, they can occur under a range of atmospheric conditions. For example, all Northern California landslide events assessed are associated with moderate to strong atmospheric rivers (ARs), while Southern California landslides feature non-AR to strong AR conditions. The storm events evaluated herein share many characteristics of hydrologically important storms in California that did not necessarily result in landslides; thus, atmospheric characteristics alone may not be sufficient to determine whether landslides will occur. However, documenting the characteristics of landslide-triggering storms defines the conditions under which landslides tend to occur, provides analog events that can be useful in forecast applications, helps define future research directions relating to atmospheric conditions and landslides, and supports interdisciplinary research efforts.

California↗

USGS2023

Using integrated growth to delineate debris-flow inundation

Debris-flow volume is fundamental to mobility, yet many debris flows change volume as they travel. Growth can occur through diverse processes such as channel-bed entrainment, bank failures, aggregation of landslides, and coalescence of multiple flows. Integrating growth, either over upslope area or stream length, combines the effects of these growth processes and requires specification of only the growth zone extent and a growth factor. To delineate potential debris-flow inundation, we implement integrated growth factors and simple volume-area relations in a new USGS software package, Grfin Tools. We present two examples of forecasting debris-flow inundation – one using an area growth factor in Puerto Rico and another using a channel-length growth factor in Oregon, USA. The use of growth zones and growth factors enables scenario-based hazard assessments for geomorphic settings with debris-flow growth.

Conference Paper↗

USGS2020

Debris-flow growth in Puerto Rico during Hurricane Maria: Preliminary results from analyses of pre- and post-event lidar data

On September 20, 2017, Hurricane Maria triggered widespread debris flows in Puerto Rico. We used field observations and pre- and post-Maria lidar to study the volumetric growth of long-travelled (>400 m) debris flows in four basins. We found overall growth rates that ranged from 0.7 to 30.4 m 3 per meter of channel length. We partitioned the rates into two growth mechanisms, aggregation of multiple landslides, or erosion and entrainment of channel sediment. In three basins, landslides accounted for more than 80% of the total debris-flow volumes. In one basin, entrainment accounted for 96% of the volume. These results indicate that forecasting volumes for regional debris-flow inundation modeling is more complicated than estimating the number and volume of contributing landslide source areas, although this task is difficult by itself. In this preliminary analysis, we did not find geologic, topographic, or morphometric variables that correlated with the growth observations. We suspect that the observed growth rates were heavily influenced by local variations in environmental conditions, including antecedent soil moisture conditions, duration and intensity of rainfall, and availability of channel material. Given these considerations, regional debris-flow inundation modeling may be best achieved by using a suite of scenarios that capture possible mechanisms of debris-flow growth.

Puerto Rico↗

USGS2019

Debris-flow initiation promoted by extension within a slow-moving landslide

The dynamics of slow landslide motion can predispose oversteepened and extended slide regions to debris-flow initiation. For more than 20 years, our real-time monitoring, combined with repeat high-precision GPS surveys, of the Cleveland Corral landslide complex, California, USA, reveals that debris flows initiate from slow-moving kinematic elements of this complex. Different slide elements move in different wet years, and all remain dormant in dry years. To explore controls on landslide-element kinematics, we use triaxial testing to define the critical state behavior of the landslide material, and use a large-diameter sampling ring to determine in situ material porosities in both extensional and compressional regions of the slide. Regions undergoing extension contain materials looser than their critical state, potentially aiding liquefaction and debris-flow mobilization from shallow, secondary slides. Although intense rainfall serves as a trigger for debris-flow initiation, slow deformation of the larger landslide promotes debris-flow formation by oversteeepening toe and lateral margins and by preferentially extending, and effectively loosening, material in these steep regions.

California↗

USGS2015

Scoops3D: software to analyze 3D slope stability throughout a digital landscape

The computer program, Scoops3D, evaluates slope stability throughout a digital landscape represented by a digital elevation model (DEM). The program uses a three-dimensional (3D) method of columns approach to assess the stability of many (typically millions) potential landslides within a user-defined size range. For each potential landslide (or failure), Scoops3D assesses the stability of a rotational, spherical slip surface encompassing many DEM cells using a 3D version of either Bishop’s simplified method or the Ordinary (Fellenius) method of limit-equilibrium analysis. Scoops3D has several options for the user to systematically and efficiently search throughout an entire DEM, thereby incorporating the effects of complex surface topography. In a thorough search, each DEM cell is included in multiple potential failures, and Scoops3D records the lowest stability (factor of safety) for each DEM cell, as well as the size (volume or area) associated with each of these potential landslides. It also determines the least-stable potential failure for the entire DEM. The user has a variety of options for building a 3D domain, including layers or full 3D distributions of strength and pore-water pressures, simplistic earthquake loading, and unsaturated suction conditions. Results from Scoops3D can be readily incorporated into a geographic information system (GIS) or other visualization software. This manual includes information on the theoretical basis for the slope-stability analysis, requirements for constructing and searching a 3D domain, a detailed operational guide (including step-by-step instructions for using the graphical user interface [GUI] software, Scoops3D-i) and input/output file specifications, practical considerations for conducting an analysis, results of verification tests, and multiple examples illustrating the capabilities of Scoops3D. Easy-to-use software installation packages are available for the Windows or Macintosh operating systems; these packages install the compiled Scoops3D program, the GUI (Scoops3D-i), and associated documentation. Several Scoops3D examples, including all input and output files, are available as well. The source code is written in the Fortran 90 language and can be compiled to run on any computer operating system with an appropriate compiler.

Techniques and Methods↗

USGS2014

Plenary: Progress in Regional Landslide Hazard Assessment—Examples from the USA

Landslide hazard assessment at local and regional scales contributes to mitigation of landslides in developing and densely populated areas by providing information for (1) land development and redevelopment plans and regulations, (2) emergency preparedness plans, and (3) economic analysis to (a) set priorities for engineered mitigation projects and (b) define areas of similar levels of hazard for insurance purposes. US Geological Survey (USGS) research on landslide hazard assessment has explored a range of methods that can be used to estimate temporal and spatial landslide potential and probability for various scales and purposes. Cases taken primarily from our work in the U.S. Pacific Northwest illustrate and compare a sampling of methods, approaches, and progress. For example, landform mapping using high-resolution topographic data resulted in identification of about four times more landslides in Seattle, Washington, than previous efforts using aerial photography. Susceptibility classes based on the landforms captured 93 % of all historical landslides (all types) throughout the city. A deterministic model for rainfall infiltration and shallow landslide initiation, TRIGRS, was able to identify locations of 92 % of historical shallow landslides in southwest Seattle. The potentially unstable areas identified by TRIGRS occupied only 26 % of the slope areas steeper than 20°. Addition of an unsaturated infiltration model to TRIGRS expands the applicability of the model to areas of highly permeable soils. Replacement of the single cell, 1D factor of safety with a simple 3D method of columns improves accuracy of factor of safety predictions for both saturated and unsaturated infiltration models. A 3D deterministic model for large, deep landslides, SCOOPS, combined with a three-dimensional model for groundwater flow, successfully predicted instability in steep areas of permeable outwash sand and topographic reentrants. These locations are consistent with locations of large, deep, historically active landslides. For an area in Seattle, a composite of the three maps illustrates how maps produced by different approaches might be combined to assess overall landslide potential. Examples from Oregon, USA, illustrate how landform mapping and deterministic analysis for shallow landslide potential have been adapted into standardized methods for efficiently producing detailed landslide inventory and shallow landslide susceptibility maps that have consistent content and format statewide.

Conference Paper↗

USGS2010

Preliminary slope-stability analysis of Augustine Volcano

Augustine Volcano has been a prolific producer of large debris avalanches during the Holocene. Originating as landslides from the steep upper edifice, these avalanches typically slide into the surrounding ocean. At least one debris avalanche that occurred in 1883 during an eruption initiated a far-traveled tsunami. The possible occurrence of another edifice collapse and ensuing tsunami was a concern during the 2006 eruption of Augustine. To aid in hazard assessments, we have evaluated the slope stability of Augustine's edifice, using a quasi-three-dimensional, geotechnically based slope-stability model implemented in the computer program SCOOPS. We analyzed the effects of topography, variations in rock strength, and earthquake-induced strong ground motion on the relative stability of millions of potential large (>0.1 km 3 volume) slope failures throughout the edifice. Preliminary results from pre-2006 topography provide three insights. First, the predicted stability of all parts of the upper edifice is approximately the same, suggesting an equal likelihood of slope failure, in agreement with geologic observations that debris avalanches have swept all sectors of the volcano. Second, the least stable (by a small amount) sector is on the east flank where a debris avalanche would flow into deeper ocean water and a resulting tsunami would be directed toward the southwestern part of the Kenai Peninsula. Third, most model scenarios predict stable edifice slopes, and only scenarios assuming extensive weak rocks and moderate to strong ground shaking predict potential large collapses. Because other transient triggering mechanisms, such as shallow magma intrusion, may be needed to instigate slope instability, monitoring ground deformation and seismicity could

Alaska↗

USGS2008

Assessing deep-seated landslide susceptibility using 3-D groundwater and slope-stability analyses, southwestern Seattle, Washington

In Seattle, Washington, deep-seated landslides on bluffs along Puget Sound have historically caused extensive damage to land and structures. These large failures are controlled by three-dimensional (3-D) variations in strength and pore-water pressures. We assess the slope stability of part of southwestern Seattle using a 3-D limit-equilibrium analysis coupled with a 3-D groundwater flow model. Our analyses use a high-resolution digital elevation model (DEM) combined with assignment of strength and hydraulic properties based on geologic units. The hydrogeology of the Seattle area consists of a layer of permeable glacial outwash sand that overlies less permeable glacial lacustrine silty clay. Using a 3-D groundwater model, MODFLOW-2000, we simulate a water table above the less permeable units and calibrate the model to observed conditions. The simulated pore-pressure distribution is then used in a 3-D slope-stability analysis, SCOOPS, to quantify the stability of the coastal bluffs. For wet winter conditions, our analyses predict that the least stable areas are steep hillslopes above Puget Sound, where pore pressures are elevated in the outwash sand. Groundwater flow converges in coastal reentrants, resulting in elevated pore pressures and destabilization of slopes. Regions predicted to be least stable include the areas in or adjacent to three mapped historically active deep-seated landslides. The results of our 3-D analyses differ significantly from a slope map or results from one-dimensional (1-D) analyses.

Washington↗

USGS2008

Deciphering landslide behavior using large-scale flume experiments

Landslides can be triggered by a variety of hydrologic events and they can exhibit a wide range of movement dynamics. Effective prediction requires understanding these diverse behaviors. Precise evaluation in the field is difficult; as an alternative we performed a series of landslide initiation experiments in the large-scale, USGS debris-flow flume. We systematically investigated the effects of three different hydrologic triggering mechanisms, including groundwater exfiltration from bedrock, prolonged rainfall infiltration, and intense bursts of rain. We also examined the effects of initial soil porosity (loose or dense) relative to the soil’s critical-state porosity. Results show that all three hydrologic mechanisms can instigate landsliding, but water pathways, sensor response patterns, and times to failure differ. Initial soil porosity has a profound influence on landslide movement behavior. Experiments using loose soil show rapid soil contraction during failure, with elevated pore pressures liquefying the sediment and creating fast-moving debris flows. In contrast, dense soil dilated upon shearing, resulting in slow, gradual, and episodic motion. These results have fundamental implications for forecasting landslide behavior and developing effective warning systems.

Conference Paper↗

USGS2007

Modeling 3-D slope stability of coastal bluffs using 3-D ground-water flow, Southwestern Seattle, Washington

Landslides are a common problem on coastal bluffs throughout the world. Along the coastal bluffs of the Puget Sound in Seattle, Washington, landslides range from small, shallow failures to large, deep-seated landslides. Landslides of all types can pose hazards to human lives and property, but deep-seated landslides are of significant concern because their large areal extent can cause extensive property damage. Although many geomorphic processes shape the coastal bluffs of Seattle, we focus on large (greater than 3,000 m3), deepseated, rotational landslides that occur on the steep bluffs along Puget Sound. Many of these larger failures occur in advance outwash deposits of the Vashon Drift (Qva); some failures extend into the underlying Lawton Clay Member of the Vashon Drift (Qvlc). The slope stability of coastal bluffs is controlled by the interplay of three-dimensional (3-D) variations in gravitational stress, strength, and pore-water pressure. We assess 3-D slope-stability using SCOOPS (Reid and others, 2000), a computer program that allows us to search a high-resolution digital-elevation model (DEM) to quantify the relative stability of all parts of the landscape by computing the stability and volume of thousands of potential spherical failures. SCOOPS incorporates topography, 3-D strength variations, and 3-D pore pressures. Initially, we use our 3-D analysis methods to examine the effects of topography and geology by using heterogeneous material properties, as defined by stratigraphy, without pore pressures. In this scenario, the least-stable areas are located on the steepest slopes, commonly in Qva or Qvlc. However, these locations do not agree well with observations of deep-seated landslides. Historically, both shallow colluvial landslides and deep-seated landslides have been observed near the contact between Qva and Qvlc, and commonly occur in Qva. The low hydraulic conductivity of Qvlc impedes ground-water flow, resulting in elevated pore pressures at the base of Qva, thereby increasing the potential for landslides. Our analysis simulates the ground-water flow using the results of a 3-D ground-water flow model, MODFLOW-2000 (Harbaugh and others, 2000), to generate a 3-D pore-pressure field. Areas of elevated pore pressure reflect the influence of a perched ground-water table in Qva, as well as ground-water convergence in the coastal re-entrants. We obtain a realistic model of deep-seated landsliding by combining 3-D pore pressures with heterogeneous strength properties. The results show the least-stable areas where pore pressures are locally elevated in Qva. We compare our results with records of past landslides. The predicted leaststable areas include two historically active deep-seated landslides and areas adjacent to these landslides.

Scientific Investigations Report↗