Geology ReportsSearch

Geology topics

Daniel Buscombe

Publications and source records attributed to Daniel Buscombe.

4 recordsLinked to original sources

Wave runup and total water level observations from time series imagery at several sites with varying nearshore morphologies

Coastal imaging systems have been developed to measure wave runup and total water level (TWL) at the shoreline, which is a key metric for assessing coastal flooding and erosion. However, extracting quantitative measurements from coastal images has typically been done through the laborious task of hand-digitization of wave runup timestacks. Timestacks are images created by sampling a cross-shore array of pixels from an image through time as waves propagate towards and run up a beach. We utilize over 7000 hand-digitized timestacks from six diverse locations to train and validate machine learning models to automate the process of TWL extraction. Using these data, we evaluate two deep learning model architectures for the task of runup detection. One is based on a fully convolutional architecture trained from scratch, and the other is a transformer-based architecture trained using transfer learning. The deep learning models provide a probability of each pixel being either wet or dry. When contoured at the 50% level (equal chance of being wet or dry), the deep learning models more accurately identified TWL maxima than minima at all sites. This resulted in accurate predictions of 2% exceedance runup, but under predictions of significant swash and over predictions of wave setup. Improved agreement with the complete TWL time series was obtained through post-processing by utilizing the wet/dry probability of each pixel to weight the contouring toward lower dryness probabilities for runup minima (maxima agreed well with observations without tuning). Overall, a transformer-based model using transfer learning provided the best agreement with wave runup statistics, including a) the 2% exceedance runup, b) significant swash, and c) wave setup at the shoreline. For a random subset of images, the model was found to be within the uncertainty range of hand-digitization. The relative success of the transfer learning model suggests that fine-tuning a large model has advantages compared to training a smaller model from scratch. Models provide per-pixel probabilistic estimates in less than 10 s per timestack on a single computational unit, versus the more than 5 min required for hand-digitization. The model is therefore well-suited for near real-time applications, allowing for the development of early warning systems for difficult to forecast events. Real-time wave runup and total water level observations can also be incorporated into coastal hazards forecasts for data assimilation and continual model validation and improvement.

Coastal Engineering

Autonomous bed-sediment imaging-systems for revealing temporal variability of grain size

We describe a remotely operated video microscope system, designed to provide high-resolution images of seabed sediments. Two versions were developed, which differ in how they raise the camera from the seabed. The first used hydraulics and the second used the energy associated with wave orbital motion. Images were analyzed using automated frequency-domain methods, which following a rigorous partially supervised quality control procedure, yielded estimates to within 20% of the true size as determined by on-screen manual measurements of grains. Long-term grain-size variability at a sandy inner shelf site offshore of Santa Cruz, California, USA, was investigated using the hydraulic system. Eighteen months of high frequency (min to h), high-resolution (μm) images were collected, and grain size distributions compiled. The data constitutes the longest known high-frequency record of seabed-grain size at this sample frequency, at any location. Short-term grain-size variability of sand in an energetic surf zone at Praa Sands, Cornwall, UK was investigated using the ‘wave-powered’ system. The data are the first high-frequency record of grain size at a single location of a highly mobile and evolving bed in a natural surf zone. Using this technology, it is now possible to measure bed-sediment-grain size at a time-scale comparable with flow conditions. Results suggest models of sediment transport at sandy, wave-dominated, nearshore locations should allow for substantial changes in grain-size distribution over time-scales as short as a few hours.

California

Currents, drag, and sediment transport induced by a tsunami

We report observations of water surface elevation, currents, and suspended sediment concentration (SSC) from a 10-m deep site on the inner shelf in northern Monterey Bay during the arrival of the 2010 Chile tsunami. Velocity profiles were measured from 3.5 m above the bed (mab) to the surface at 2 min intervals, and from 0.1 to 0.7 mab at 1 Hz. SSC was determined from the acoustic backscatter of the near-bed profiler. The initial tsunami waves were directed cross shore and had a period of approximately 16 min. Maximum wave height was 1.1 m, and maximum current speed was 0.36 m/s. During the strongest onrush, near-bed velocities were clearly influenced by friction and a logarithmic boundary layer developed, extending more than 0.3 mab. We estimated friction velocity and bed shear stress from the logarithmic profiles. The logarithmic structure indicates that the flow can be characterized as quasi-steady at these times. At other phases of the tsunami waves, the magnitude of the acceleration term was significant in the near-bed momentum equation, indicating unsteady flow. The maximum tsunami-induced bed shear stress (0.4 N/m 2 ) exceeded the critical shear stress for the medium-grained sand on the seafloor. Cross-shore sediment flux was enhanced by the tsunami. Oscillations of water surface elevation and currents continued for several days. The oscillations were dominated by resonant frequencies, the most energetic of which was the fundamental longitudinal frequency of Monterey Bay. The maximum current speed (hourly-timescale) in 18 months of observations occurred four hours after the tsunami arrived.

California

Advances in the simulation and automated measurement of well-sorted granular material: 1. Simulation

1. In this, the first of a pair of papers which address the simulation and automated measurement of well-sorted natural granular material, a method is presented for simulation of two-phase (solid, void) assemblages of discrete non-cohesive particles. The purpose is to have a flexible, yet computationally and theoretically simple, suite of tools with well constrained and well known statistical properties, in order to simulate realistic granular material as a discrete element model with realistic size and shape distributions, for a variety of purposes. The stochastic modeling framework is based on three-dimensional tessellations with variable degrees of order in particle-packing arrangement. Examples of sediments with a variety of particle size distributions and spatial variability in grain size are presented. The relationship between particle shape and porosity conforms to published data. The immediate application is testing new algorithms for automated measurements of particle properties (mean and standard deviation of particle sizes, and apparent porosity) from images of natural sediment, as detailed in the second of this pair of papers. The model could also prove useful for simulating specific depositional structures found in natural sediments, the result of physical alterations to packing and grain fabric, using discrete particle flow models. While the principal focus here is on naturally occurring sediment and sedimentary rock, the methods presented might also be useful for simulations of similar granular or cellular material encountered in engineering, industrial and life sciences.

Journal of Geophysical Research F: Earth Surface