Geology topics

Craig A. Senter

Publications and source records attributed to Craig A. Senter.

9 recordsLinked to original sources

USGS2022

Relative contributions of suspended sediment between the upper Suiattle River Basin and a non-glacial tributary, Washington, May 2016–September 2017

Concentrations of suspended sediment were measured in discrete samples and turbidity was continuously monitored at four U.S. Geological Survey streamgages in western Washington State, including one gage on the Sauk River; two gages on the Suiattle River, a tributary to the Sauk River; and one gage on Downey Creek, a tributary to the Suiattle River. The Suiattle River is a sediment-rich stream with headwaters on Glacier Peak, a glaciated volcano in the northern Cascade Range. Contributions of suspended sediment to the Suiattle River from unglaciated tributaries, represented by Downey Creek, were compared to the contributions from Glacier Peak in the upper Suiattle River watershed. During summer 2017, a period for which complete records of discharge and sediment data were available for all three streamgages in the Suiattle River Basin, the suspended-sediment load from Downey Creek (drainage area [DA] 93 square kilometers [km 2 ]) was 1,400 metric tons, which is equivalent to a sediment yield of about 15 metric tons per km 2 . During the same period, the suspended-sediment load from the upper Suiattle River (DA 176 km 2 ) was 142,000 metric tons, or a sediment yield of about 800 metric tons per km 2 ; and the suspended-sediment load from the lower Suiattle River (DA 733 km 2 ) was 230,000 metric tons, or a sediment yield of about 300 metric tons per km 2 . The Downey Creek Basin accounts for 13 percent of the drainage area of the Suiattle River watershed but contributed only 0.6 percent of the suspended-sediment load over the summer of 2017 and water year 2017 (October 1, 2016–September 30, 2017). In contrast, the upper Suiattle River Basin, which accounts for 24 percent of the entire Suiattle River watershed, contributed 62 percent of the suspended-sediment load during the summer of 2017. Given the short period for which data were collected, it cannot be known with certainty whether the above values are representative of long-term means. The relatively minor contribution of suspended sediment from Downey Creek, however, is consistent with the expectation that the upper Suiattle River, which drains Glacier Peak, is the dominant contemporary source of suspended sediment to the Sauk River. During summer 2016, the suspended-sediment load in the upper Siuattle River (180,000 metric tons) was more than double the estimated load in the lower Sauk River (80,000 metric tons), even though the upper Suiattle River represents only 10 percent of the total contributing area to the lower Sauk River Basin. This ratio of relative contribution is interpreted as an indication of transient storage of sediment along the Suiattle and Sauk Rivers between the two streamgaging stations. In the glaciated upper Suiattle River Basin, sediment is transported by annual glacial-melt processes in spring and summer months, deposited during the summer base-flow period, and then remobilized by fall and winter floods for delivery to the lower Sauk River.

Washington↗

USGS2020

Evaluation of the Washington State Department of Transportation stormwater monitoring and effectiveness program for 2014–19

The U.S. Geological Survey was asked by the Washington State Department of Transportation to provide technical assistance as a third-party reviewer of their stormwater effectiveness monitoring program during the transition between the completion of the 2014 Washington State Department of Ecology permit requirements and start of the new 2019 Washington State Department of Ecology permit requirements. For the purposes of this evaluation, the U.S. Geological Survey reviewed Washington State Department of Transportation’s 2014 National Pollution Discharge Elimination System permit. This review focuses on sections S7, S8, G9, and appendix 4 of the permit that are specific to monitoring. These sections cover the methods of monitoring, the constituents that were monitored, laboratory requirements, reporting requirements, and data archival. Next, all quality-assurance project plans for the 2014 general permit and annual reports required for the permit were reviewed. The quality-assurance project plans and annual reports were reviewed to ensure that monitoring was executed and reported as required by the 2014 general permit. The monitoring requirements put forth from the permits were fully addressed in quality-assurance project plans and were completed and presented in the annual monitoring reports. Overall, the Washington State Department of Transportation monitoring program does not change much under its new 2019 permit. The Washington State Department of Transportation has followed through with the plan set out in each of its approved quality-assurance project plans and therefore, is in a good position to meet or exceed the new permit requirements in the upcoming 5-year permit cycle.

Open-File Report↗

USGS2020

Assessment of existing groundwater quality data in the Green-Duwamish watershed, Washington

The United States Geological Survey (USGS) provided technical support to the Washington Department of Ecology (Ecology) in their assessment of the role groundwater plays in contributing pollutant loading to the Green-Duwamish River near Seattle, Washington. Ecology is developing watershed hydrology models of the Green-Duwamish watershed, and need to assign realistic contaminant concentrations to the various Hydrologic Response Units represented in their models. The USGS compiled existing groundwater quality data in the Green-Duwamish watershed, and this report summarizes results and interpretation of the dataset, including identifying data gaps and needs for further research and monitoring. The sources of existing data were the USGS’s National Water Information System, Ecology’s Environmental Information Management System, and a compilation of several studies by Leidos, a scientific research company. The water-quality parameters of interest included polychlorinated biphenyl (PCB) Aroclors and congeners, phthalates, carcinogenic polycyclic aromatic hydrocarbons (cPAHs), arsenic, copper, and zinc. Results were grouped into the four subwatersheds delineated in Ecology’s hydrology models: Duwamish, Lower Green, Soos, and Upper Green. Results from the Duwamish subwatershed were further sub-divided by the USGS into the Lower Duwamish, containing land adjacent to the Lower Duwamish Waterway Superfund site, and the Upper Duwamish, containing the remaining area of the Duwamish subwatershed. Groundwater quality data in the Lower Duwamish were treated separately because there is known contamination in this area. The availability of water quality data varied by subwatershed as follows: phthalate data was only available within the Duwamish, PCB data was available within the Duwamish and Lower Green, cPAH data was available within the Duwamish, Lower Green, and Soos, and data for arsenic, copper, and zinc were available within all four subwatersheds. More than 99 percent of the available data was within the Duwamish subwatershed, identifying a need for additional monitoring of groundwater quality in the other subwatersheds.

Washington↗

USGS2018

Hydrology-driven chemical loads transported by the Green River to the Lower Duwamish Waterway near Seattle, Washington, 2013–17

The sediments in the Lower Duwamish Waterway Superfund site in Seattle, Washington, are contaminated with chemicals including metals such as arsenic, polychlorinated biphenyls (PCBs), carcinogenic polycyclic aromatic hydrocarbons (cPAHs), and dioxins/furans from decades of intense anthropogenic activities. The U.S. Geological Survey, in cooperation with the Washington State Department of Ecology, collected new data from 2013 to 2017 to estimate sediment and chemical loads transported by the Green/Duwamish River to the Lower Duwamish Waterway Superfund site (the final 8-kilometer reach of the river) in support of sediment remediation within the site. Chemical loads were calculated as the product of river suspended-sediment loads and suspended sediment-bound chemical concentrations measured at river kilometer 16.7. Using four different approaches, annual suspended sediment-bound chemical load estimates transported by the river to the Lower Duwamish Waterway were in the range of 1,120–1,470 kilograms arsenic, 2,810–8,200 grams (g) toxic equivalent cPAHs, 205–407 milligrams toxic equivalent dioxins/furans, and 340–1,180 g PCBs. Storm events contributed a disproportionately large amount of the load of anthropogenic organic compounds such as cPAHs (54 percent), dioxins/furans (44 percent), and PCBs (52 percent) as compared to overall time (17 percent). Chemical concentrations and load estimates often were underestimated using results from unfiltered water analysis only, especially in samples with high suspended-sediment concentrations and for hydrophobic organic chemicals such as cPAHs that prefer to sorb to particulates and are at low concentrations near or below the analytical limits of water methods. For metals and PCBs, the dissolved concentration was relatively low and consistent between sampling events, whereas the suspended sediment-bound chemical concentrations contributed most of the chemical concentration in the water column during periods of high river suspended-sediment concentrations. However, the dissolved fraction, on average, contributed more than one-third of the estimated total chemical load in the river system for arsenic and PCBs, even given the hydrophobic nature of the chemicals. These results suggest that the sum of the chemical concentrations measured on two separate fractions—the particulate fraction and the dissolved fraction—more fully represents the total chemical concentration as compared to analysis of an unfiltered water sample, especially in samples with high suspended-sediment concentrations. Most of the suspended-sediment load (97 percent) and sediment-bound chemical load (92–94 percent) occurred during the wet winter half of the year from October 15 to April 14. However, the highest sediment-bound chemical concentrations often occurred during short intense storms or “first flush” autumn runoff events during the dry summer half of the year from April 15 to October 14. Because of the highly variable and dynamic river system characteristics (including precipitation, discharge, sediment concentration, and tidal fluctuations), it is critical to characterize the occurrence, frequency, concentrations, and loads during extreme conditions (for example, when the river is affected by storm-derived runoff) rather than time-averaged conditions. These short extreme events have a high potential for acute effects on ecological and human health, and may have a great influence on the effectiveness of the sediment remediation activities that are underway in the Lower Duwamish Waterway.

Washington↗

USGS2018

Suspended-sediment transport from the Green-Duwamish River to the Lower Duwamish Waterway, Seattle, Washington, 2013–17

The Green-Duwamish River transports watershed-derived sediment to the Lower Duwamish Waterway Superfund site near Seattle, Washington. Understanding the amount of sediment transported by the river is essential to the bed sediment cleanup process. Turbidity, discharge, suspended-sediment concentration (SSC), and particle-size data were collected by the U.S. Geological Survey (USGS) from February 2013 to January 2017 at the Duwamish River, Washington, within the tidal influence at river kilometer 16.7 (USGS streamgage 12113390; Duwamish River at Golf Course at Tukwila, WA). This report quantifies the timing and magnitude of suspended-sediment transported in the Duwamish River. Regression models were developed between SSC and turbidity and SSC and discharge to estimate 15- minute SSC. Suspended-sediment loads were calculated from the computed SSC and time-series discharge data for every 15-minute interval during the study period. The 2014–16 average annual suspended-sediment load computed was 117,246 tons (106,364 metric tons), of which 73.5 percent or (86,191 tons; 78,191 metric tons) was fine particle (less than 0.0625 millimeter in diameter) suspended sediment. The seasonality of this site is apparent when you divide the year into "wet" (October 16– April 15) and "dry" (April 16–October 15) seasons. Most (97 percent) of the annual suspended sediment was transported during the wet season, when brief periods of intense precipitation from storms, large releases from the Howard Hanson Dam, or a combination of both were much more frequent.

Washington↗

USGS2018

Chemical concentrations in water and suspended sediment, Green River to Lower Duwamish Waterway near Seattle, Washington, 2016–17

From August 2016 to March 2017, the U.S. Geological Survey (USGS) collected representative samples of filtered and unfiltered water and suspended sediment (including the colloidal fraction) at USGS streamgage 12113390 (Duwamish River at Golf Course, at Tukwila, Washington) during 13 periods of differing flow conditions. Samples were analyzed by Washington-State-accredited laboratories for a large suite of compounds, including metals, dioxins/furans, semivolatile compounds including polycyclic aromatic hydrocarbons, butyltins, the 209 polychlorinated biphenyl (PCB) congeners, and total and dissolved organic carbon. Concurrent with the chemistry sampling, water-quality field parameters were measured, and representative water samples were collected and analyzed for river suspended-sediment concentration and particle-size distribution. The results provide new data that can be used to estimate sediment and chemical loads transported by the Green River to the Lower Duwamish Waterway.

Washington↗

USGS2016

Continuous-flow centrifugation to collect suspended sediment for chemical analysis

Recent advances in suspended-sediment monitoring tools and surrogate technologies have greatly improved the ability to quantify suspended-sediment concentrations and to estimate daily, seasonal, and annual suspended-sediment fluxes from rivers to coastal waters. However, little is known about the chemical composition of suspended sediment, and how it may vary spatially between water bodies and temporally within a single system owing to climate, seasonality, land use, and other natural and anthropogenic drivers. Many water-quality contaminants, such as organic and inorganic chemicals, nutrients, and pathogens, preferentially partition in sediment rather than water. Suspended sediment-bound chemical concentrations may be undetected during analysis of unfiltered water samples, owing to small water sample volumes and analytical limitations. Quantification of suspended sediment‑bound chemical concentrations is needed to improve estimates of total chemical concentrations, chemical fluxes, and exposure levels of aquatic organisms and humans in receiving environments. Despite these needs, few studies or monitoring programs measure the chemical composition of suspended sediment, largely owing to the difficulty in consistently obtaining samples of sufficient quality and quantity for laboratory analysis. A field protocol is described here utilizing continuous‑flow centrifugation for the collection of suspended sediment for chemical analysis. The centrifuge used for development of this method is small, lightweight, and portable for the field applications described in this protocol. Project scoping considerations, deployment of equipment and system layout options, and results from various field and laboratory quality control experiments are described. The testing confirmed the applicability of the protocol for the determination of many inorganic and organic chemicals sorbed on suspended sediment, including metals, pesticides, polycyclic aromatic hydrocarbons, and polychlorinated biphenyls. The particle-size distribution of the captured sediment changes to a more fine-grained sample during centrifugation, and the necessity to account for this change when extrapolating chemical concentrations on the centrifuged sediment sample to the environmental water system is discussed. The data produced using this method will help eliminate a data gap of suspended sediment-bound chemical concentrations, and will support management decisions, such as chemical source-control efforts or in-stream restoration activities. When coupled with streamflow and sediment flux data, it will improve estimates of riverine chemical fluxes, and will aid in assessing the importance and impacts of suspended sediment-bound chemicals to downstream freshwater and coastal marine ecosystems.

Techniques and Methods↗

USGS2015

Chemical concentrations and instantaneous loads, Green River to the Lower Duwamish Waterway near Seattle, Washington, 2013–15

In November 2013, U.S. Geological Survey streamgaging equipment was installed at a historical water-quality station on the Duwamish River, Washington, within the tidal influence at river kilometer 16.7 (U.S. Geological Survey site 12113390; Duwamish River at Golf Course at Tukwila, WA). Publicly available, real-time continuous data includes river streamflow, stream velocity, and turbidity. Between November 2013 and March 2015, the U.S. Geological Survey collected representative samples of water, suspended sediment, or bed sediment from the streamgaging station during 28 periods of differing flow conditions. Samples were analyzed by Washington-State-accredited laboratories for a large suite of compounds, including metals, dioxins/furans, semivolatile compounds including polycyclic aromatic hydrocarbons, pesticides, butytins, polychlorinated biphenyl (PCB) Aroclors and the 209 PCB congeners, volatile organic compounds, hexavalent chromium, and total and dissolved organic carbon. Metals, PCB congeners, and dioxins/furans were frequently detected in unfiltered-water samples, and concentrations typically increased with increasing suspended-sediment concentrations. Chemical concentrations in suspendedsediment samples were variable between sampling periods. The highest concentrations of many chemicals in suspended sediment were measured during summer and early autumn storm periods. Median chemical concentrations in suspended-sediment samples were greater than median chemical concentrations in fine bed sediment (less than 62.5 µm) samples, which were greater than median chemical concentrations in paired bulk bed sediment (less than 2 mm) samples. Suspended-sediment concentration, sediment particle-size distribution, and general water-quality parameters were measured concurrent with the chemistry sampling. From this discrete data, combined with the continuous streamflow record, estimates of instantaneous sediment and chemical loads from the Green River to the Lower Duwamish Waterway were calculated. For most compounds, loads were higher during storms than during baseline conditions because of high streamflow and high chemical concentrations. The highest loads occurred during dam releases (periods when stored runoff from a prior storm is released from the Howard Hanson Dam into the upper Green River) because of the high river streamflow and high suspended-sediment concentration, even when chemical concentrations were lower than concentrations measured during storm events.

Washington↗

USGS2009

Reconnaissance Assessment of the Potential for Roadside Dry Wells to Affect Water Quality on the Island of Hawai'i

The County of Hawai'i Department of Public Works (DPW) uses dry wells to dispose of stormwater runoff from roads. Recently, concern has been raised that water entering the dry wells may transport contaminants to groundwater and affect the quality of receiving waters. The DPW operates 2,052 dry wells. Compiling an inventory of these dry wells and sorting it on the basis of presence or absence of urbanization in the drainage area, distance between the bottom of the dry well and the water table, and proximity to receiving waters helps identify the dry wells having greatest potential to affect the quality of receiving waters so that future studies or mitigation efforts can focus on a smaller number of dry wells. The drainage areas of some DPW dry wells encompass urbanized areas, which could be a source of contaminants. Some dry wells penetrate close to or through the water table, eliminating or substantially reducing opportunities for contaminant attenuation between the ground surface and water table. Dry wells that have drainage areas that encompass urbanization, penetrate to near the water table, and are near the coast have the highest potential to affect the quality of coastal waters (this study did not consider specific sections of coastline that may be of greater concern than others). Some DPW dry wells, including a few that have drainage areas that encompass urbanization, lie within the areas contributing recharge (ACR) to drinking-water wells. Numerical groundwater modeling studies by previous investigators indicate that water infiltrating those dry wells could eventually be pumped at drinking-water wells. Dry wells that have a high potential for affecting coastal receiving waters or drinking-water wells can be the focus of studies to further understand the effect of the dry wells on the quality of receiving waters. Possible study approaches include sampling for contaminants at the dry well and receiving water, injecting and monitoring the movement of tracers, and numerical modeling. To fully assess whether dry wells actually pose a significant contamination threat to receiving waters, results from modeling or monitoring must be compared to limits for contaminant concentration at receiving waters. These limits are usually established by the agencies tasked with protecting those waters.

Scientific Investigations Report↗