Geology topics

Charles P. Dunning

Publications and source records attributed to Charles P. Dunning.

9 recordsLinked to original sources

USGS2015

Simulation of the regional groundwater-flow system of the Menominee Indian Reservation, Wisconsin

A regional, two-dimensional, steady-state groundwater-flow model was developed to simulate the groundwater-flow system and groundwater/surface-water interactions within the Menominee Indian Reservation. The model was developed by the U.S. Geological Survey (USGS), in cooperation with the Menominee Indian Tribe of Wisconsin, to contribute to the fundamental understanding of the region’s hydrogeology. The objectives of the regional model were to improve understanding of the groundwater-flow system, including groundwater/surface-water interactions, and to develop a tool suitable for evaluating the effects of potential regional water-management programs. The computer code GFLOW was used because of the ease with which the model can simulate groundwater/surface-water interactions, provide a framework for simulating regional groundwater-flow systems, and be refined in a stepwise fashion to incorporate new data and simulate groundwater-flow patterns at multiple scales. Simulations made with the regional model reproduce groundwater levels and stream base flows representative of recent conditions (1970–2013) and illustrate groundwater-flow patterns with maps of (1) the simulated water table and groundwater-flow directions, (2) probabilistic areas contributing recharge to high-capacity pumped wells, and (3) estimation of the extent of infiltrated wastewater from treatment lagoons. The groundwater-flow model described in this report simulates the major hydrogeologic features of the modeled area, including surficial unconsolidated aquifers, groundwater/surface-water interactions, and groundwater withdrawals from existing high-capacity production wells. Areas contributing recharge to pumped high-capacity wells on the Menominee Indian Reservation were delineated by tracking simulated water particles from the water table to wells in combination with Monte Carlo techniques, and maps of the probability of capture for each well nest were produced. Groundwater-agebased areas contributing recharge to wells were simulated by using the calibrated set of parameters and porosity values adjusted to account for bias in simulated saturated thickness. Simulations were performed for current (2013) pumping rates. The simulations show a range in sensitivity of the simulated areas contributing recharge to wells given the parameters evaluated through the Monte Carlo analysis. The areas contributing recharge to supply wells for the villages of Zoar and Neopit are long and narrow, with a sharp gradation from high to low probability of capture. The areas contributing recharge to supply wells for Middle Village and the village of Keshena exhibit a sharp gradation from high to low probability over a relatively small area between the well and a local groundwater mound. The highest probability areas contributing recharge to the supply wells for the Villages of Onekewat and Redwing are in the immediate vicinity of the wells. These wells also have an extensive area with low probability for capturing water that is likely due to a locally low hydraulic gradient and the large degree of uncertainty associated with the lakebed resistance parameters that control interaction between groundwater and local lakes. Additional field investigations and associated local model refinements would facilitate further reductions in uncertainty associated with simulated areas contributing recharge to the wells. The likely extent of the Neopit wastewater plume was simulated by using the groundwater-flow model and Monte Carlo techniques to evaluate the sensitivity of predictive simulations to a range of model parameter values. Wastewater infiltrated from the currently operating lagoons flows predominantly south toward Tourtillotte Creek. Some of the infiltrated wastewater is simulated as having a low probability of flowing beneath Tourtillotte Creek to the nearby West Branch Wolf River. Results for the probable extent of the wastewater plume are considered to be qualitative because the method only considers advective flow and does not account for processes affecting contaminant transport in porous media. Therefore, results for the probable extent of the wastewater plume are sensitive to the number of particles used to represent flow from the lagoon and the resolution of a synthetic grid used for the analysis. Nonetheless, it is expected that the qualitative results may be of use for identifying potential downgradient areas of concern that can then be evaluated using the quantitative “area contributing recharge to wells” method or traditional contaminant-transport simulations.

Wisconsin↗

USGS2010

Simulation of the shallow groundwater-flow system near the Hayward Airport, Sawyer County, Wisconsin

There are concerns that removal and trimming of vegetation during expansion of the Hayward Airport in Sawyer County, Wisconsin, could appreciably change the character of a nearby cold-water stream and its adjacent environs. In cooperation with the Wisconsin Department of Transportation, a two-dimensional, steady-state groundwater-flow model of the shallow groundwater-flow system near the Hayward Airport was refined from a regional model of the area. The parameter-estimation code PEST was used to obtain a best fit of the model to additional field data collected in February 2007 as part of this study. The additional data were collected during an extended period of low runoff and consisted of water levels and streamflows near the Hayward Airport. Refinements to the regional model included one additional hydraulic-conductivity zone for the airport area, and three additional parameters for streambed resistance in a northern tributary to the Namekagon River and in the main stem of the Namekagon River. In the refined Hayward Airport area model, the calibrated hydraulic conductivity was 11.2 feet per day, which is within the 58.2 to 7.9 feet per day range reported for the regional glacial and sandstone aquifer, and is consistent with a silty soil texture for the area. The calibrated refined model had a best fit of 8.6 days for the streambed resistance of the Namekagon River and between 0.6 and 1.6 days for the northern tributary stream. The previously reported regional groundwater-recharge rate of 10.1 inches per year was adjusted during calibration of the refined model in order to match streamflows measured during the period of extended low runoff; this resulted in an optimal groundwater-recharge rate of 7.1 inches per year during this period. The refined model was then used to simulate the capture zone of the northern tributary to the Namekagon River.

Scientific Investigations Report↗

USGS2008

Ground-Water Flow in the Vicinity of the Ho-Chunk Nation Communities of Indian Mission and Sand Pillow, Jackson County, Wisconsin

An analytic element ground-water-flow model was constructed to help understand the ground-water-flow system in the vicinity of the Ho-Chunk Nation communities of Indian Mission and Sand Pillow in Jackson County, Wisconsin. Data from interpretive reports, well-drillers' construction reports, and an exploratory augering program in 2003 indicate that sand and gravel of varying thickness (0-150 feet[ft]) and porous sandstone make up a composite aquifer that overlies Precambrian crystalline rock. The geometric mean values for horizontal hydraulic conductivity were estimated from specific-capacity data to be 61.3 feet per day (ft/d) for sand and gravel, 6.6 ft/d for sandstone, and 12.0 ft/d for the composite aquifer. A ground-water flow model was constructed, the near field of which encompassed the Levis and Morrison Creeks Watershed. The flow model was coupled to the parameter-estimation program UCODE to obtain a best fit between simulated and measured values of ground-water levels and estimated Q50 flow duration (base flow). Calibration of the model with UCODE provided a ground-water recharge rate of 9 inches per year and a horizontal hydraulic conductivity of 13 ft/d for the composite aquifer. Using these calibrated parameter values, simulated heads from the model were on average within 5 ft of the measured water levels. In addition, these parameter values provided an acceptable base-flow calibration for Hay, Dickey, and Levis Creeks; the calibration was particularly close for Levis Creek, which was the most frequently measured stream in the study area. The calibrated model was used to simulate ground-water levels and to determine the direction of ground-water flow in the vicinity of Indian Mission and Sand Pillow communities. Backward particle tracking was conducted for Sand Pillow production wells under two pumping simulations to determine their 20-year contributing areas. In the first simulation, new production wells 6, 7, and 8 were each pumped at 50 gallons per minute (gal/min). In the second simulation, new production wells 6, 7, and 8 and existing production well 5 were each pumped at 50 gal/min. The second simulation demonstrated interference between the existing production well 5 and the new production wells when all were pumping at 50 gal/min.

Scientific Investigations Report↗

USGS2007

Lithostratigraphic and Hydrogeologic Characteristics of the Ordovician Sinnipee Group in the Vicinity of Waupun, Fond du Lac County, Wisconsin, 1995-96

Three boreholes were drilled at a farm site near Waupun, Wis., to improve the understanding of regional hydrogeology of the Ordovician Sinnipee Group. At the site the Sinnipee Group is the uppermost bedrock unit and is found to be about 183 ft thick. On the basis of core descriptions by the Illinois State Geological Survey, the Sinnipee Group at the site comprises (stratigraphically lowest to highest) the Platteville Formation (about 51 ft thick), the Decorah Formation (about 14 ft thick), and the Galena Dolomite (about 119 ft thick). The Illinois State Geological Survey noted that hardgrounds were common in the rock core, some having stratigraphic significance. Four very well developed hardgrounds were identified, three of which were used as formation or member contacts. The hardground at about 797 ft NGVD 29 represents the top of the Platteville Formation, the hardground at about 754 ft represents the top of the Pecatonica Member of the Platteville Formation, and the hardground at about 746 ft represents the top of the Glenwood Formation. On the basis of samples collected from one borehole, the ground water at the site is of the calcium-magnesium bicarbonate type. Trichloroethene was detected in one sample at a concentration of 1 ?g/L, and the concentration of antimony in one sample exceeded the U.S. Environmental Protection Agency (USEPA) Primary Drinking Water Standard. Other water samples contained aluminum and sodium in concentrations that exceeded the USEPA Secondary Drinking Water Standard and the USEPA Drinking Water Equivalent Level, respectively. Samples from various depths contained concentrations of iron, manganese, or dissolved manganese that were near or exceeded the USEPA Secondary Drinking Water Standard. The cross-borehole radar tomography data show differences in velocity and attenuation among the three major units in the Sinnipee Group. Matrix porosity measured in rock-core samples correlates well with these velocity and attenuation tomograms. The Galena Dolomite has the lowest mean porosity at 2.4 percent (7 samples) and is represented in the tomograms as generally having the lowest attenuation and greatest velocity. Below the Galena Dolomite is a transition to a zone with the greatest attenuation and lowest velocity on the tomograms. The rock core shows this interval to be the shaley dolomite of the Decorah Formation which has a mean porosity of 8.3 percent (2 samples). Below the Decorah Formation, the Platteville Formation has a mean porosity of 3.6 percent (6 samples) and is represented in the tomograms as having velocity and attenuation generally intermediate between the Galena Dolomite and the Decorah Formation. The evaluation of the single-hole directional ground-penetrating radar reflection survey in FL-800 identified 15 reflectors (secondary permeability features). Some of the reflectors do correlate with fractures and partings noted on geophysical logs and rock core; however, many additional fractures and partings identified by the televiewer log and/or core description were not measured by the borehole radar survey. Horizontal or sub-horizontal reflectors (bedding-plane partings) which do correlate with indications of bedding-plane partings on the acoustic televiewer intersect the borehole at about 917 ft, 907 ft, 870 ft, 805 ft, and 797 ft. The flowmeter profiles indicate that water entering and exiting the boreholes at seven bedding-plane partings accounts for most of the total borehole transmissivity. The flowmeter profiles in all three boreholes show that more than 90 percent of the total borehole transmissivity is provided by bedding-plane partings found at 870 ft and higher stratigraphically within the Galena Dolomite. Static water levels were measured in selected intervals of the three boreholes, and vertical hydraulic gradients were estimated by comparing levels in adjacent intervals. Gradients were found to be almost uniformly downward, ranging from -0.040 to -1.251 ft/ft. On th

Scientific Investigations Report↗

USGS2006

Development and application of a screening model for simulating regional ground-water flow in the St. Croix River basin, Minnesota and Wisconsin

A series of databases and an accompanying screening model were constructed by the U.S. Geological Survey, in cooperation with the National Park Service, to better understand the regional ground-water-flow system and its relation to stream drainage in the St. Croix River Basin. The St. Croix River and its tributaries drain about 8,000 square miles in northeastern Minnesota and northwestern Wisconsin. The databases contain information for the entire St. Croix River Basin pertaining to well logs, lithology, thickness of lithologic groups, ground-water levels, streamflow, and well pumpage. Maps and generalized cross sections created from the compiled data show the lithologic groups, extending from the water table to the crystalline bedrock, through which ground water flows. These lithologic groups are: fine-grained unconsolidated deposits; coarse-grained unconsolidated deposits; sandstone bedrock; carbonate bedrock; and other bedrock lithologies including shale, siltstone, conglomerate, and igneous intrusions. The steady-state screening model treats the ground-water-flow system as a single layer with transmissivity zones that reflect the distribution of lithologic groups, and with recharge zones that correspond to general areas of high or low evapotranspiration. The model includes representation of second- and higher-order streams and municipal and other high-capacity production wells. The analytic-element model code GFLOW was used to simulate the regional ground-water flow, the water-table surface across the St. Croix River Basin, and base-flow contributions from ground water to streams. In addition, the model routes tributary base flow through the stream network to the St. Croix River. The parameter-estimation inverse model UCODE was linked to the GFLOW model to select the combination of parameter values best able to match over 5,000 water-level measurements and base-flow estimates at 22 streamflow-gaging stations. Results from the calibrated screening model show ground-water contributing areas for selected stream reaches within the basin. The delineation of these areas is useful to water-resource managers concerned with protection of fisheries and other resources. The model results also identify the areas of the basin where ground-water travel time from the water table to streams and wells is relatively short (less than 50 years). Ninety percent of the simulated ground-water pathlines require travel times between 3 and 260 years. The median pathline distance traversed and the median pathline velocity were 1.7 mi and 177 ft/y, respectively. It is important to recognize the limitations of this screening model. Heterogeneities in subsurface properties and in recharge rates are considered only at a very broad scale (miles to tens of miles). No account is taken of vertical variations in properties or pumping rates, and no provision is made to account for stacked ground-water-flow systems that have different flow patterns at different depths. Small-scale (hundreds to thousands of feet) flow systems associated with minor water bodies are neglected, and as a result, the model is not useful for simulating typical site-specific problems. Despite its limitations, the model serves as a framework for understanding the regional pattern of ground-water flow and as a starting point for a generation of more targeted and detailed ground-water models that would be needed to address emerging water-supply and water-quality concerns in the St. Croix River Basin.

Scientific Investigations Report↗

USGS2005

Lithology, hydraulic properties, and water quality of the Sandstone Aquifer in the northwestern part of the Bad River Indian Reservation, Wisconsin, 1998-1999

The Precambrian sandstone aquifer in the northwestern part of the Bad River Band of Lake Superior Tribe of Chippewa Indians Reservation, Ashland County, Wisconsin, provides much of the drinking water to area residents. A study was undertaken in cooperation with the Bad River Tribe to provide specific information about the lithology, hydraulic properties, and water quality of the sandstone aquifer. During 1998 and 1999, the U.S. Geological Survey installed three monitoring wells, collected and analyzed lithologic and water samples, and conducted geophysical logging and aquifer tests to characterize the sandstone aquifer. The two monitoring wells in the southeastern part of the study area, the Diaperville Monitoring Well #1 (Diaperville MW #1) and the Tolman Monitoring Well #1 (Tolman MW #1) , are believed to have encountered older Middle Proterozoic Oronto Group sandstones. The sandstone encountered in the Ackley Monitoring Well #1 (Ackley MW #1) is believed to be Chequamegon Sandstone of the Late Proterozoic Bayfield Group. This interpretation is based on previous studies, as well as thin- section analysis of sandstone core recovered from the Ackley Monitoring Well #1. Results of aquifer tests conducted in the Diaperville Monitoring Well #1 and the Tolman Monitoring Well #1 provide ranges for hydraulic param - eter values in the sandstone aquifer: transmissivity ranges from 83 to 509 square feet per day; hydraulic conductivity ranges from 1.6 to 4.5 feet per day; storativity ranges from 0.00019 to 0.00046; and specific capacity ranges from 0.22 to 0.67 gallons per minute per foot. Though high- and low-angle fractures are present in Ackley Monitoring Well #1 core, the hydraulic properties of the bedrock appear to be due largely to the matrix porosity measured in thin section (16–21 percent) and permeability of the sandstone. The aquifer test for the Diaperville Monitoring Well #1 resulted in observed drawdown in nearby glacial wells, evidence of a hydraulic connection between the sandstone aquifer and the glacial deposits. Major ion analyses indicate that the water sampled from the sandstone aquifer at the Ackley site is of the calcium-magnesium-sodium- bicarbonate type. Based on a single sampling set, volatile organic constituents were not detected in water samples from the Diaperville Monitoring Well #1 or the Ackley Monitoring Well #1.

Wisconsin↗

USGS2004

A cross-site comparison of methods used for hydrogeologic characterization of the Galena-Platteville aquifer in Illinois and Wisconsin, with examples from selected Superfund sites

The effectiveness of 28 methods used to characterize the fractured Galena-Platteville aquifer at eight sites in northern Illinois and Wisconsin is evaluated. Analysis of government databases, previous investigations, topographic maps, aerial photographs, and outcrops was essential to understanding the hydrogeology in the area to be investigated. The effectiveness of surface-geophysical methods depended on site geology. Lithologic logging provided essential information for site characterization. Cores were used for stratigraphy and geotechnical analysis. Natural-gamma logging helped identify the effect of lithology on the location of secondary- permeability features. Caliper logging identified large secondary-permeability features. Neutron logs identified trends in matrix porosity. Acoustic-televiewer logs identified numerous secondary-permeability features and their orientation. Borehole-camera logs also identified a number of secondary-permeability features. Borehole ground-penetrating radar identified lithologic and secondary-permeability features. However, the accuracy and completeness of this method is uncertain. Single-point-resistance, density, and normal resistivity logs were of limited use. Water-level and water-quality data identified flow directions and indicated the horizontal and vertical distribution of aquifer permeability and the depth of the permeable features. Temperature, spontaneous potential, and fluid-resistivity logging identified few secondary-permeability features at some sites and several features at others. Flowmeter logging was the most effective geophysical method for characterizing secondary-permeability features. Aquifer tests provided insight into the permeability distribution, identified hydraulically interconnected features, the presence of heterogeneity and anisotropy, and determined effective porosity. Aquifer heterogeneity prevented calculation of accurate hydraulic properties from some tests. Different methods, such as flowmeter logging and slug testing, occasionally produced different interpretations. Aquifer characterization improved with an increase in the number of data points, the period of data collection, and the number of methods used.

Scientific Investigations Report↗

USGS2000

Altitude, depth, and thickness of the Galena-Platteville Bedrock Unit in the subcrop area of Illinois and Wisconsin

The Galena-Platteville bedrock unit is a carbonate deposit of Ordovician age, composed of the Galena and Platteville Groups in Illinois and the Sinnippee Group in Wisconsin. It is the uppermost bedrock unit (subcrop) in most of northern Illinois and southern and eastern Wisconsin. The subcrop area is shaded in figure 1 of sheet 1 (Batten and others, 1997). The unit is predominately dolomite, with limestone in some areas, and has a weathered surface. Across the subcrop area, the hydrologic characteristics of the bedrock unit vary substantially. The bedrock unit may be either a confining unit or an aquifer. In areas where the Galena-Platteville bedrock unit is an aquifer, the unit is a dependable source of water for many private wells and some municipal-water-supply systems. Ground water in the Galena-Platteville bedrock aquifer is susceptible to contamination because the bedrock unit is near land surface in much of the study area, and the fractures in the unit allow rapid movement of water providing limited capacity to attenuate contaminants. The subcrop (study) area covers approximately 7,850 square miles in northern Illinois and Wisconsin. In the study area, volatile organic compounds and other contaminants have been detected in the aquifer at various sites (Mills, 1993; Kay and others, 1994). Many sources of contaminants, including landfills and industrial facilities, are known or suspected. In order to determine the possible effects of contamination on the ground-water supply, an understanding of the regional hydrogeologic framework of the Galena-Platteville bedrock unit is needed. Published and unpublished map and point data describing the geologic properties of the Galena-Platteville bedrock unit are available from many sources. The U.S. Geological Survey (USGS), in cooperation with the U.S. Environmental Protection Agency (USEPA), has selected and compiled a large portion of the available data to create computer data bases and maps. The objective of this effort is to compile and publish these data in a series of reports (U.S. Geological Survey Water-Resources Investigations Reports (WRIR) 974054-A, WRIR 97-4054-B, WRIR 97-4054-C). This is the third in that series of reports. The report describes the altitude, thickness, and depth from land surface of the subcrop area of the Galena-Platteville bedrock unit. The report series will enable investigators involved in site-specific studies within the subcrop area to understand the regional geologic framework of the unit and to find additional reference sources. This report consists of four sheets that show the altitude (sheet 1), depth from land surface (sheet 2), total thickness (sheet 3), and location of altitude data (sheet 4) of the lithologic units that constitute the Galena-Platteville bedrock unit within the subcrop area. The sheets also show major known geologic features within the Galena-Platteville study area in Illinois and Wisconsin. A geographic information system (GIS) was used to generate data layers (coverages) from point data and from published and unpublished contour maps at various scales and detail. Standard GIS procedures were used to change the coverages into the maps shown on the sheets presented in this report. A list of references for the data used to prepare the maps is provided.

Illinois, Wisconsin↗

USGS1999

Hydrogeologic properties of the Ordovician Sinnipee Group at test well BN-483, Better Brite Superfund Site, De Pere, Wisconsin

Test well BN-483, near the Better Brite Superfund Site, was drilled to a total depth of 169 feet below land surface. The Ordovician-age Sinnipee Group, which includes the Galena Dolomite, and the Decorah and Platteville Formations, was encountered from about 25 feet below land surface to a depth of about 160 feet. Analysis of core samples and single-well aquifer tests of the dolomites indicate low matrix porosity (1.8 to 7.7 percent) and low horizontal hydraulic conductivity (5.0 x 10 -4 to 3.4 x 10 -3 feet per day). Significant differences in hydraulic head between Sinnipee Group dolomites and the underlying Sandstone Aquifer (represented by the Glenwood Formation sandstones in test well BN-483) are the result of municipal pumping from the Sandstone Aquifer. The difference in hydraulic head, along with the low porosity and hydraulic conductivity of the Sinnipee Group dolomites, indicates limited hydraulic connection between the Sandstone Aquifer and the shallow aquifer within the glacial sediments. Because of the low hydraulic conductivity of the dolomites, sufficient water for analysis was recovered from only the uppermost interval of test well BN-483 at a depth of 35-52 feet. No inorganic contaminants of environmental concern were detected. Toluene was the only VOC identified, at an estimated concentration of about 2 micrograms/liter.

Wisconsin↗