Geology topics

Carolyn Boulton

Publications and source records attributed to Carolyn Boulton.

3 recordsLinked to original sources

USGS2018

Frictional properties and 3-D stress analysis of the southern Alpine Fault, New Zealand

New Zealand's Alpine Fault (AF) ruptures quasi-periodically in large-magnitude earthquakes. Paleoseismological evidence suggests that about half of all recognized AF earthquakes terminated at the boundary between the Central and South Westland sections of the fault. There, fault geometry and the polarity of uplift change. The South Westland AF exhibits oblique-normal fault motion on a structure oriented 052°/82°SE that, for at least 35 km along strike, contains saponite-rich principal slip zone gouges. New hydrothermal friction experiments reveal that the saponite fault gouge is frictionally weak, exhibiting friction coefficients between μ = 0.12 and μ = 0.16 for a range of temperatures ( T = 25–210 °C) and effective normal stresses ( σ n ' = 31.2–93.6 MPa). The saponite gouge is rate-strengthening in all velocity steps performed at velocities between 0.01 and 3.0 μm/s, behavior conducive to aseismic creep. A three-dimensional stress analysis shows that the South Westland AF is favorably oriented with respect to the regional stress field for slip within the frictionally weak saponite fault gouge. Geometrically, the fault is severely misoriented for slip in any fault-forming materials with friction coefficients exceeding μ ∼0.5. The combination of weak gouges prone to aseismic creep, strong asperities , and low resolved shear stress may impede earthquake rupture propagation along the South Westland Alpine Fault.

Journal of Structural Geology↗

USGS2017

Bedrock geology of DFDP-2B, central Alpine Fault, New Zealand

During the second phase of the Alpine Fault, Deep Fault Drilling Project (DFDP) in the Whataroa River, South Westland, New Zealand, bedrock was encountered in the DFDP-2B borehole from 238.5–893.2 m Measured Depth (MD). Continuous sampling and meso- to microscale characterisation of whole rock cuttings established that, in sequence, the borehole sampled amphibolite facies, Torlesse Composite Terrane-derived schists, protomylonites and mylonites, terminating 200–400 m above an Alpine Fault Principal Slip Zone (PSZ) with a maximum dip of 62°. The most diagnostic structural features of increasing PSZ proximity were the occurrence of shear bands and reduction in mean quartz grain sizes. A change in composition to greater mica:quartz + feldspar, most markedly below c. 700 m MD, is inferred to result from either heterogeneous sampling or a change in lithology related to alteration. Major oxide variations suggest the fault-proximal Alpine Fault alteration zone, as previously defined in DFDP-1 core, was not sampled.

New Zealand Journal of Geology and Geophysics↗

USGS2014

Frictional properties of exhumed fault gouges in DFDP-1 cores, Alpine Fault, New Zealand

Principal slip zone gouges recovered during the Deep Fault Drilling Project (DFDP-1), Alpine Fault, New Zealand, were deformed in triaxial friction experiments at temperatures, T , of up to 350°C, effective normal stresses, σ n ′, of up to 156 MPa, and velocities between 0.01 and 3 µm/s. Chlorite/white mica-bearing DFDP-1A blue gouge, 90.62 m sample depth, is frictionally strong (friction coefficient, μ , 0.61–0.76) across all experimental conditions tested ( T = 70–350°C, σ n ′ = 31.2–156 MPa); it undergoes a transition from positive to negative rate dependence as T increases past 210°C. The friction coefficient of smectite-bearing DFDP-1B brown gouge, 128.42 m sample depth, increases from 0.49 to 0.74 with increasing temperature and pressure ( T = 70–210°C, σ n ′ = 31.2–93.6 MPa); the positive to negative rate dependence transition occurs as T increases past 140°C. These measurements indicate that, in the absence of elevated pore fluid pressures, DFDP-1 gouges are frictionally strong under conditions representative of the seismogenic crust.

Alpine Fault↗