Geology Reports⌕ Search

Geology topics

C. Hans Nelson

Publications and source records attributed to C. Hans Nelson.

14 recordsLinked to original sources
USGS2013

Thermogenic gases in near-surface sediments of Norton Sound, Alaska

A plume of hydrocarbon gases, assumed to be of thermogenic origin based on chemical compositions, has been noted by others in the water column of Norton Sound about 40 km south of Nome, Alaska. We used detailed geophysical transects, side-scan sonar, underwater television, and chromatographic analyses of gases in near-surface sediments to define a probable source area of hydrocarbon gases at the southern apex of the water plume epicenter. Geophysical, geotechnical, and geochemical evidence together indicate that hydrocarbon gases of subsurface, thermogenic origin apparently migrate into the near surface sediments along a fault zone. Subbottom reflector terminations on continuous seismic profiles outline a large zone of anomalous acoustic responses about 9 km in diameter and at 100-m depth that may be caused by a subsurface accumulation of gas. Gas migration from the accumulation to the surface sediment is indicated by smaller zones of reflector terminations observed in high-resolution profiles and by seafloor craters seen on underwater television at one station. The presence of gas-charged surface sediment also is suggested by low percent pore water saturation, greater penetration of the penetrometer, and more rapid penetration of the vibracorer in sediment at the station with near-surface acoustic anomalies and seafloor craters. Analyses of hydrocarbon gases in sediments from a 1.6-m vibracore taken at this station showed unusually high concentrations of hydrocarbon gases heavier than methane; the ethane, propane, n-butane, and isobutane were 76, 4, 6, and 52 times greater than in other near-surface sediments in this region, and also significant quantities of gasoline-range hydrocarbons were present. The gas composition and presence in near-surface sediments above a thick underlying section with acoustic anomalies points to the possibility of petroleum at depth in this region. Our work indicates that surface and near-surface studies of the continental shelf may contribute significantly to petroleum-resource evaluations in addition to defining areas of potential hazard from gas-charged sediment.

Alaska↗
USGS2012

Turbidite event history—Methods and implications for Holocene paleoseismicity of the Cascadia subduction zone

Turbidite systems along the continental margin of Cascadia Basin from Vancouver Island, Canada, to Cape Mendocino, California, United States, have been investigated with swath bathymetry; newly collected and archive piston, gravity, kasten, and box cores; and accelerator mass spectrometry radiocarbon dates. The purpose of this study is to test the applicability of the Holocene turbidite record as a paleoseismic record for the Cascadia subduction zone. The Cascadia Basin is an ideal place to develop a turbidite paleoseismologic method and to record paleoearthquakes because (1) a single subduction-zone fault underlies the Cascadia submarine-canyon systems; (2) multiple tributary canyons and a variety of turbidite systems and sedimentary sources exist to use in tests of synchronous turbidite triggering; (3) the Cascadia trench is completely sediment filled, allowing channel systems to trend seaward across the abyssal plain, rather than merging in the trench; (4) the continental shelf is wide, favoring disconnection of Holocene river systems from their largely Pleistocene canyons; and (5) excellent stratigraphic datums, including the Mazama ash and distinguishable sedimentological and faunal changes near the Pleistocene-Holocene boundary, are present for correlating events and anchoring the temporal framework. Multiple tributaries to Cascadia Channel with 50- to 150-km spacing, and a wide variety of other turbidite systems with different sedimentary sources contain 13 post-Mazama-ash and 19 Holocene turbidites. Likely correlative sequences are found in Cascadia Channel, Juan de Fuca Channel off Washington, and Hydrate Ridge slope basin and Astoria Fan off northern and central Oregon. A probable correlative sequence of turbidites is also found in cores on Rogue Apron off southern Oregon. The Hydrate Ridge and Rogue Apron cores also include 12-22 interspersed thinner turbidite beds respectively. We use 14 C dates, relative-dating tests at channel confluences, and stratigraphic correlation of turbidites to determine whether turbidites deposited in separate channel systems are correlative - triggered by a common event. In most cases, these tests can separate earthquake-triggered turbidity currents from other possible sources. The 10,000-year turbidite record along the Cascadia margin passes several tests for synchronous triggering and correlates well with the shorter onshore paleoseismic record. The synchroneity of a 10,000-year turbidite-event record for 500 km along the northern half of the Cascadia subduction zone is best explained by paleoseismic triggering by great earthquakes. Similarly, we find a likely synchronous record in southern Cascadia, including correlated additional events along the southern margin. We examine the applicability of other regional triggers, such as storm waves, storm surges, hyperpycnal flows, and teletsunami, specifically for the Cascadia margin. The average age of the oldest turbidite emplacement event in the 10-0-ka series is 9,800±~210 cal yr B.P. and the youngest is 270±~120 cal yr B.P., indistinguishable from the A.D. 1700 (250 cal yr B.P.) Cascadia earthquake. The northern events define a great earthquake recurrence of ~500-530 years. The recurrence times and averages are supported by the thickness of hemipelagic sediment deposited between turbidite beds. The southern Oregon and northern California margins represent at least three segments that include all of the northern ruptures, as well as ~22 thinner turbidites of restricted latitude range that are correlated between multiple sites. At least two northern California sites, Trinidad and Eel Canyon/pools, record additional turbidites, which may be a mix of earthquake and sedimentologically or storm-triggered events, particularly during the early Holocene when a close connection existed between these canyons and associated river systems. The combined stratigraphic correlations, hemipelagic analysis, and 14 C framework suggest that the Cascadia margin has three rupture modes: (1) 19-20 full-length or nearly full length ruptures; (2) three or four ruptures comprising the southern 50-70 percent of the margin; and (3) 18-20 smaller southern-margin ruptures during the past 10 k.y., with the possibility of additional southern-margin events that are presently uncorrelated. The shorter rupture extents and thinner turbidites of the southern margin correspond well with spatial extents interpreted from the limited onshore paleoseismic record, supporting margin segmentation of southern Cascadia. The sequence of 41 events defines an average recurrence period for the southern Cascadia margin of ~240 years during the past 10 k.y. Time-independent probabilities for segmented ruptures range from 7-12 percent in 50 years for full or nearly full margin ruptures to ~21 percent in 50 years for a southern-margin rupture. Time-dependent probabilities are similar for northern margin events at ~7-12 percent and 37-42 percent in 50 years for the southern margin. Failure analysis suggests that by the year 2060, Cascadia will have exceeded ~27 percent of Holocene recurrence intervals for the northern margin and 85 percent of recurrence intervals for the southern margin. The long earthquake record established in Cascadia allows tests of recurrence models rarely possible elsewhere. Turbidite mass per event along the Cascadia margin reveals a consistent record for many of the Cascadia turbidites. We infer that larger turbidites likely represent larger earthquakes. Mass per event and magnitude estimates also correlate modestly with following time intervals for each event, suggesting that Cascadia full or nearly full margin ruptures weakly support a time-predictable model of recurrence. The long paleoseismic record also suggests a pattern of clustered earthquakes that includes four or five cycles of two to five earthquakes during the past 10 k.y., separated by unusually long intervals. We suggest that the pattern of long time intervals and longer ruptures for the northern and central margins may be a function of high sediment supply on the incoming plate, smoothing asperities, and potential barriers. The smaller southern Cascadia segments correspond to thinner incoming sediment sections and potentially greater interaction between lower-plate and upper-plate heterogeneities. The Cascadia Basin turbidite record establishes new paleoseismic techniques utilizing marine turbidite-event stratigraphy during sea-level highstands. These techniques can be applied in other specific settings worldwide, where an extensive fault traverses a continental margin that has several active turbidite systems.

British Columbia, California, Oregon, Washington↗
USGS1994

The volcanic, sedimentologic, and paleolimnologic history of the Crater Lake caldera floor, Oregon:Evidence for small caldera evolution

Apparent phreatic explosion craters, caldera-floor volcanic cones, and geothermal features outline a ring fracture zone along which Mount Mazama collapsed to form the Crater Lake caldera during its climactic eruption about 6,850 yr B.P. Within a few years, subaerial deposits infilled the phreatic craters and then formed a thick wedge (10-20 m) of mass flow deposits shed from caldera walls. Intense volcanic activity (phreatic explosions, subaerial flows, and hydrothermal venting) occurred during this early postcaldera stage, and a central platform of subaerial andesite flows and scoria formed on the caldera floor. Radiocarbon ages suggest that deposition of Iacustrine hemipelagic sediment began on the central platform about 150 yr after the caldera collapse. This is the minimum time to fill the lake halfway with water and cover the platform assuming present hydrologic conditions of precipitation and evaporation but with negligible leakage of lake water. Wizard Island formed during the final part of the 300-yr lake-filling period as shown by its (1) upper subaerial lava flows from 0 to -70 m below present water level and lower subaqueous lava flows from -70 to -500 m and by (2) lacustrine turbidite sand derived from Wizard Island that was deposited on the central platform about 350 yr after the caldera collapse. Pollen stratigraphy indicates that the warm and dry climate of middle Holocene time correlates with the early lake deposits. Diatom stratigraphy also suggests a more thermally stratified and phosphate-rich environment associated respectively with this climate and greater hydrothermal activity during the early lake history. Apparent coarse-grained and thick-bedded turbidites of the early lake beds were deposited throughout northwest, southwest, and eastern basins during the time that volcanic and seismic activity formed the subaqueous Wizard Island, Merriam Cone, and rhyodacite dome. The last known postcaldera volcanic activity produced a subaqueous rhyodacite ash bed and dome about 4,240 yr B.P. The late lake beds with base-of-slope aprons and thin, fine-grained basin-plain turbidites were deposited during the volcanically quiescent period of the past 4,000 yr. Deposits in Crater Lake and on similar caldera floors suggest that four stages characterize the postcaldera evolution of smaller (≤10 km in diameter) terrestrial caldera lake floors: (1) initial-stage caldera collapse forms the ring fracture zone that controls location of the main volcanic eruptive centers and sedimentary basin depocenters on the caldera floor; (2) early-stage subaerial sedimentation rapidly fills ring-fracture depressions and constructs basin-floor debris fans from calderawall landslides; (3) first-stage subaqueous sedimentation deposits thick flat-lying lake turbidites throughout basins, while a thin blanket of hemipelagic sediment covers volcanic edifices that continue to form concurrently with lake sedimentation; and (4) second-stage subaqueous sedimentation after the waning of major volcanic activity and the earlier periods of most rapid sedimentation develops small sili-ciclastic basin base-of-slope turbidite aprons and central basin plains. Renewed volcanic activity or lake destruction could cause part or all of the cycle to repeat.

Oregon↗
USGS1993

Mediterranean undercurrent sandy contourites, Gulf of Cadiz, Spain

The Pliocene—Quaternary pattern of contourite deposits on the eastern Gulf of Cadiz continental slope results from an interaction between linear diapiric ridges that are perpendicular to slope contours and the Mediterranean undercurrent that has flowed northwestward parallel to the slope contours and down valleys between the ridges since the late Miocene opening of the Strait of Gibraltar. Coincident with the northwestward decrease in undercurrent speeds from the Strait there is the following northwestward gradation of sediment facies associations: (1) upper slope facies, (2) sand dune facies on the upstream mid-slope terrace, (3) large mud wave facies on the lower slope, (4) sediment drift facies banked against the diapiric ridges, and (5) valley facies between the ridges. The southeastern sediment drift facies closest to Gibraltar contains medium-fine sand beds interbedded with mud. The adjacent valley floor facies is composed of gravelly, shelly coarse to medium sand lags and large sand dunes on the valley margins. Compared to this, the northwestern drift contains coarse silt interbeds and the adjacent valley floors exhibit small to medium sand dunes of fine sand. Further northwestward, sediment drift grades to biogenous silt near the Faro Drift at the Portuguese border. Because of the complex pattern of contour-parallel and valley-perpendicular flow paths of the Mediterranean undercurrent, the larger-scale bedforms and coarser-grained sediment of valley facies trend perpendicular to the smaller-scale bedforms and finer-grained contourite deposits of adjacent sediment drift facies. The bottom-current deposits of valleys and the contourites of the Cadiz slope intervalley areas are distinct from turbidite systems. The valley sequences are not aggradational like turbidite channel—levee complexes, but typically exhibit bedrock walls against ridges, extensive scour and fill into adjacent contourites, transverse bedform fields and bioclastic lag deposits. Both valley and contourite deposits exhibit reverse graded bedding and sharp upper bed contacts in coarse-grained layers, low deposition rates, and a regional pattern of bedform zones, textural variation, and compositional gradation. The surface sandy contourite layer of 0.2–1.2 m thickness that covers the Gulf of Cadiz slope has formed during the present Holocene high sea level because high sea level results in maximum water depth over the Gibraltar sill and full development of the Mediterranean undercurrent. The late Pleistocene age of the mud underlying the surface sand sheet correlates with the age of the last sea-level lowstand and apparent weak Mediterranean undercurrent development. Thus, the cyclic deposition of sand or mud layers and contourite or drape sequences appear to be related to late Pliocene and Quaternary sea-level changes and Mediterranean water circulation patterns. Since its Pliocene origin, the contourite sequence has had low deposition rates of < 5 cm/1000y on the upper slope and < 13 cm/1000y in the middle slope sediment drift.

Gulf of Cadiz↗
USGS1992

Characteristics of a sandy depositional lobe on the outer Mississippi fan from SeaMARC IA sidescan sonar images

SeaMARC IA sidescan sonar images of the distal reaches of a depositional lobe on the Mississippi Fan show that channelized rather than unconfined transport was the dominant transport mechanism for coarse-grained sediment during the formation of this part of the deep-sea fan. Overbank sheet flow of sands was not an important process in the transport and deposition of the sandy and silty sediment found on this fan. The dendritic distributary pattern and the high order of splaying of the channels, only one of which appears to have been active at a time, suggest that coarse-grained deposits on this fan are laterally discontinuous.

Mississippi↗
USGS1988

The Mount Mazama climactic eruption (6900 BP) and resulting convulsive sedimentation on the continent, ocean basin, and Crater Lake caldera floor

The climactic eruption of Mount Mazama and the resulting sedimentation may have been the most significant convulsive sedimentary event in North America during Holocene time. A collapse caldera 1,200 m deep and 10 km in diameter was formed in Mount Mazama, and its floor was covered by hundreds of meters of wall-collapse debris. Wind-blown pyroclastic ash extended 2,000 km northeast from Mount Mazama and covered more than 1,000,000 km 2 of the continent. On the Pacific Ocean floor, Mazama ash was transported westward 600 to 700 km along deep-sea channels by turbidity currents. The initial single-vent phase of the climactic eruption, a Plinian column, emptied over half of the magma erupted. Debris from this phase accumulated as a pumice deposit 10 m thick at the rim to 50 cm thick as much as 100 km from the vent. This deposit created a mid-Holocene stratigraphic marker over the continent and the continental margin of western North America. A ring-vent phase followed as a second part of the climactic eruption and produced highly mobile pyroclastic flows. These flows covered the mountain for at least 14 km from the vent, continued down the valleys nearly 60 km, and deposited as much as 100 m of pumiceous ignimbrite. After the caldera collapsed as a result of the eruption of more than 50 km 3 of magma, heat of the climactic eruption apparently created phreatic explosion craters along the ring fracture zone of the caldera floor. Initially, explosion debris and sheetwash of pyroclastics off highlands seems mainly to have filled the local craters with bedded volcaniclastics. This basal, generally flat-lying unit, was quickly covered by wedges of chaotically bedded debris flow and avalanche-type deposits that thin inward from the caldera walls. These deposits may have formed in response to seismic activity associated with postcaldera volcanism that apparently began soon after the caldera collapsed. The lower two units of non-lacustrine beds (50 to 60 m) make up the majority of the postcaldera sedimentary deposits and seem to have deposited rapidly after the climactic eruption. Twenty to 25 m of lacustrine sediment has been accumulating more slowly over the subaerial debris during the past 6,900 yr. Some Mazama ash probably was transported by rivers to the sea immediately after the climactic eruption because significant amounts of this ash appear in mid-Holocene turbidites of Cascadia Basin. The presence of Mazama ash mixed with Columbia River sand in texturally and compositionally graded turbidites shows that Mazama ash periodically was moved by sediment-gravity flows down the canyons and through channels to deposition sites in the Astoria Fan and the Cascadia Channel. The coarsest and thickest tuffaceous turbidites were deposited on channel floors, and the ash-rich suspension flows that overtopped the levees were deposited as thin-bedded turbidites in interchannel areas. Study of the Mount Mazama climactic eruption shows that such an event in the Cascade Mountains has the potential to: (a) cause major destruction within 100 km of the vent, (b) severely affect biota as far as 2,000 km downwind, and (c) disrupt commercial river and marine transportation or natural sedimentation as far as several hundred kilometers in the opposite direction from wind-blown debris. Present geologic characteristics on the Crater Lake caldera floor suggest that geologic hazards from a significant volcanic event appear to be minimal for the next few thousand years.

Mount Mazama↗
USGS1981

Sand waves on an epicontinental shelf: Northern Bering Sea

Sand waves and current ripples occupy the crests and flanks of a series of large linear sand ridges (20 km × 5 km × 10 m high) lying in an open-marine setting in the northern Bering Sea. The sand wave area, which lies west of Seward Peninsula and southeast of Bering Strait, is exposed to the strong continuous flow of coastal water northward toward Bering Strait. A hierarchy of three sizes of superimposed bedforms, all facing northward, was observed in successive cruises in 1976 and 1977. Large sand waves (height 2 m; spacing 200 m) have smaller sand waves (height 1 m; spacing 20 m) lying at a small oblique angle on their stoss slopes. The smaller sand waves in turn have linguoid ripples on their stoss slopes. Repeated studies of the sand wave fields were made both years with high-resolution seismic-reflection profiles, side-scan sonographs, underwater photographs, current-meter stations, vibracores, and suspended-sediment samplers. Comparison of seismic and side-scan data collected along profile lines run both years showed changes in sand wave shape that indicate significant bedload transport within the year. Gouge marks made in sediment by keels of floating ice also showed significantly different patterns each year, further documenting modification to the bottom by sediment transport. During calm sea conditions in 1977, underwater video and camera observations showed formation and active migration of linguoid and straight-crested current ripples. Current speeds 1 m above the bottom were between 20 and 30 cm/s. Maximum current velocities and sand wave migration apparently occur when strong southwesterly winds enhance the steady northerly flow of coastal water. Many cross-stratified sand bodies in the geologic record are interpreted as having formed in a tidal- or storm-dominated setting. This study provides an example of formation and migration of large bedforms by the interaction of storms with strong uniform coastal currents in an open-marine setting.

Marine Geology↗
USGS1980

Distribution of trace elements in bottom sediment of the northern Bering Sea

2-dimensional contour and 3-dimensional value-surface maps of semi-quantitative emission spectographic analyses for over 50 elements in surface sediment from 180 sampling stations are presented. For purposes of discussion, certain of these elements have been grouped into the following categories: petroleum indicators, heavy metals, potentially toxic elements, chemically sensitive elements, major elements, minor elements, and a group of elements of economic interest.

Alaska↗
USGS1980

Graded storm sand layers offshore from the Yukon Delta, Alaska

The northern Bering Sea has a history of severe storm surges. The most recent, and perhaps the worst in historical times, occurred in November, 1974 (Fathauer, 1975). Evidence of storm surge events is exhibited in sea-floor stratigraphy as well as shoreline flooding and indicates that significant widespread changes in sea-floor sedimentation take place (Nelson and Creager, 1977). These changes have implications for installations on the sea floor and for mass transport of pollutants. This paper describes the interbedded sand layers found in southern Norton Sound off the modern Yukon Delta that are deposited by the storm surge events. Such deposits are evident in both modern and ancient deposits of epicontinental shelves (Hays, 1967; Howard and Reineck, in press; Anderton, 1976.). These graded sand layers in very shallow water mimic many of the features of thin-bedded turbidite sands, although the shallow water deposits are thought to have a very different mechanism of deposition related to storm surge processes. Two factors in the oceanographic setting of northern Bering Sea magnify the effects of storm surge. The sea floor is very shallow (less than 20 m deep over wide areas) particularly in Norton Sound. Consequently there is intensive wave reworking which causes extensive sea-floor erosion, mass movement, displacement, and offshore progradation of significant amounts of sediment during storm surges; The second factor is a system of strong dynamic_ bottom currents that can move large amounts of sediment northward to Chukchi Sea during normal weather. Much more sediment is moved when the current is reinforced by relaxing of the sea surface set-up caused by storm surge (Fig. 1) (Flemming and Heggarty, 1966; Coachman et al., 1976; Cacchione and Drake, 1979; Schumacher and Tripp, 1979). Another important influence on the sedimentation in southern Norton Sound is the effect of seasonal processes on the Yukon River delta, During the winter months from November to May the Yukon River averages 40,000 cfs when the ice-covered river is fed mainly by base flow (Dupre, 1976). Within less than a week of river breakup, peak discharges may reach 1,000,000 cfs or more and then decline throughout the summer.

Alaska↗
USGS1972

Mercury distribution in ancient and modern sediment of northeastern Bering Sea

A reconnaissance of surface and subsurface sediments to a maximum depth of 244 feet below the sea floor shows that natural mercury anomalies from 0.2 to 1.3 ppm have been present in northeastern Bering Sea since early Pliocene. The anomalies and mean values are highest in modern beach (maximum 1.3 and mean 0.22 ppm Hg) and nearshore subsurface gravels (maximum 0.6 and mean .06 ppm Hg) along the highly mineralized Seward Peninsula and in organic rich silt (maximum 0.16 and mean 0.10 ppm Hg) throughout the region; the mean values are lowest in offshore sands (0.03 ppm Hg). Although gold mining may be partially responsible for high mercury levels in the beaches near Nome, Alaska, equally high or greater concentrations of mercury occur in ancient glacial sediments immediately offshore (0.6 ppm) and in modern unpolluted beach sediments at Bluff (0.45 - 1.3 ppm); this indicates that the contamination effects of mining may be no greater than natural concentration processes in the Seward Peninsula region. The background content of mercury (0.03) throughout the central area of northeastern Bering Sea is similar to that elsewhere in the world. The low mean values (0.04 ppm) even immediately offshore from mercury-rich beaches, suggests that in the surface sediments of northeastern Bering Sea, the highest concentrations are limited to the beaches near mercury sources; occasionally, however, low mercury anomalies occur offshore in glacial drift derived from mercury source regions of Chukotka and Seward Peninsula and reworked by Pleistocene shoreline processes. The minimal values offshore may be attributable to beach entrapment of heavy minerals containing mercury and/or dilution effects of modern sedimentation.

Alaska↗