Geology topics

Anthony A. Brown

Publications and source records attributed to Anthony A. Brown.

10 recordsLinked to original sources

USGS2026

Multiple-well monitoring site adjacent to the Midway- Sunset and Buena Vista Oil Fields, Kern County, California

Groundwater quality in and around oil fields in the Southern San Joaquin Valley is of interest to many California residents that rely heavily on groundwater for domestic, commercial, and agricultural use. To help assess the effects of historical oil-field activities and natural geologic sources on groundwater near the southwest margins of the Kern County Groundwater Subbasin, a multiple-well monitoring site was installed near the administrative boundary between the Midway-Sunset and Buena Vista Oil Fields in Kern County, California. The installation of the Midway-Sunset Buena Vista multiple-well monitoring site (MSBV) supports regional analysis of the relations of oil and gas sources to groundwater quality by providing information about the geology, hydrology, geophysical properties, and water quality of the alluvial and upper Tulare aquifers in areas where groundwater data were limited. Data collected from the site included drill cuttings, whole core samples, sidewall core samples, mud-gas analysis, borehole geophysical logs, depth to water measurements, and water quality samples. Whole cores were scanned using dual energy computed tomography. Subsamples of selected cores were analyzed for density, porosity, specific retention, and bulk minerology. Thin sections of the subsamples were prepared, photographed, and examined. Two samples were analyzed using scanning electron microscope technology to examine the microporosity of diatomite laden sediment. Instrumentation installed in the wells collect hourly depth to water measurements. Analysis of the data show there is 355 feet of alluvium overlying the Tulare Formation at the well site. The contact between the two formations is an aquitard resulting in a perched aquifer in the alluvium and unconfined aquifer in the Tulare Formation. The alluvium is more heterogenous and finer grained than the Tulare Formation resulting in markedly higher porosity in the alluvium compared to the Tulare Formation. Higher specific retention observed in the alluvium is attributed to the finer grained sediment and greater abundance of reworked diatomite (as represented by opal-CT [cristobalite-tridymite]) compared to the Tulare Formation. Total dissolved solids (TDS) approached or exceeded 10,000 milligrams per liter (mg/L) in the alluvium from approximately 176 to 242 feet below land surface and at the top of the Amnicola clay at approximately 670 feet below land surface within the Tulare Formation. Elevated TDS, chloride, and boron concentrations in the alluvium and on top of the Amnicola clay likely reflect groundwater that is mixed with oil-field water. Water chemistry and modern-aged groundwater in the alluvial monitoring well (MSBV #3) are consistent with the oil-field water in the alluvium being derived from documented historical surface disposal of oil-field water upslope (northwest) of the site. Water chemistry and pre-modern groundwater age in the deeper Tulare monitoring well (MSBV #1) on top of the Amnicola clay are consistent with oil-field fluids derived from upslope natural geologic sources or old oil wells that leak in the subsurface. Shallow groundwater in the Tulare (MSBV #2) is not affected by mixing with oil-field sources.

EarthArXiv↗

USGS2024

Ambient flow and transport in long-screened, sand-packed wells: Insights into cross contamination and wellbore flow

The presence of long-screened wells with a surrounding sand pack can have a major effect on the redistribution of contaminants in groundwater, particularly when the wells are set in low-hydraulic conductivity aquifers. Such redistribution, or cross contamination, can occur through vertical flow and advective transport or by in-well mixing via multiple non-advective transport processes. A multi-method approach, including the use of single borehole dilution tracer (SBDT) logging, was undertaken to estimate vertical transport of trichloroethylene (TCE) in 8 discontinued remedial extraction wells, all constructed with long screens (100 ft, or 30.6 m long) and surrounding sand packs, at Site 25, Edwards Air Force Base, California. The site is within an enclosed drainage basin that is underlain primarily by quartz-monzonite-granitic rocks in various states of weathering. Prior to this study, little information was available on the depths of fracture zones intersecting the wellbores. Results indicate that because of in-well mixing processes, a potential redistribution of TCE of up to 9 g/d per well occurs as a consequence of leaving the wells inactive (unpumped) and unsealed, as measured by SBDT logging. Simulations of flow made with a generic model of the site show that if the wells were to be sealed with well liners, with the intent of reducing vertical TCE transport but the sand pack left intact, TCE transport decreases by 53% overall compared to leaving the wells unlined.

Environmental Earth Sciences↗

USGS2024

Nutrient chemistry in the Elizabeth Lake subwatershed—Effects of onsite wastewater treatment systems on groundwater and lake water quality, Los Angeles County, California

Nutrient (nitrogen [N] and phosphorus [P] chemistry) downgradient from onsite wastewater treatment system (OWTS) was evaluated with a groundwater study in the area surrounding Elizabeth Lake, the largest of three sag lakes within the Santa Clara River watershed of Los Angeles County, California. Elizabeth Lake is listed on the “303 (d) Impaired Waters List” for excess nutrients and is downgradient from more than 600 OWTS. The primary objective of this study was to develop a conceptual hydrogeological model to determine if discharge from OWTS is transported into shallow groundwater within the Elizabeth Lake subwatershed and contributes nutrients to Elizabeth Lake in excess of the total maximum daily load limit. An analysis of historical data and data collected for this study provided estimates of aquifer properties, such as hydraulic gradients and other parameters necessary to estimate boundary conditions. Electrical resistivity tomography (ERT) surveys were done to determine the best monitoring well locations and to estimate depth to groundwater. During 4 separate sampling events, 11 wells, 2 imported water tanks, 1 spring (sampled on March 17, 2019), and Elizabeth Lake were sampled, which occurred during February–September 2020. ERT transects and borehole geophysical measurements indicated that there were low to high resistivity materials in the subsurface and potential perched fresh water. Most of the aquifer material was characterized as sandy silt, occasionally with mixed clays and medium gravels, and was estimated to have a hydraulic conductivity from 3.28x10 −3 to 16.4 feet per day, a porosity from 0.34 to 0.42, and a hydraulic gradient from 0.01 to 0.03. Although bedrock was not obvious in ERT transects, all well depths were terminated at depths of an impassible confining layer observed to be a highly consolidated blue-gray clay. Depths to granitic bedrock, based on road outcrops and lithologic driller logs, varied throughout the study area. Depth to the bedrock was estimated to be shallow on the north side of Elizabeth Lake at approximately 30 feet below land surface (ft bls). Depth to bedrock is at 50 ft bls toward the east of the Elizabeth Lake subwatershed, which is at topographic ground surface to the north and south of the residential development. Groundwater levels ranged from approximately 0 to 12 ft bls during this study. Historical water levels ranged from 8 to 16 ft bls in the lower elevation of the study area and increased to depths of as much as 80 ft bls at higher elevations on the north and south boundaries of the Elizabeth Lake subwatershed. Water-quality samples were analyzed for major ions, nutrients, dissolved organic carbon, stable isotopes, and age-dating tracers. A principal component analysis was completed to determine organic matter sources. The proportion of recharge from imported waters, used for domestic consumption, was calculated using stable water isotopes, deuterium (δD) and oxygen (δ 18 O). Recharge from imported waters accounted for approximately 15–71 percent of the total recharge to groundwater within the study area. Total nitrogen concentrations ranged from 0.17 to 30.9 milligrams per liter (mg/L) as N, and phosphorus, measured in the soluble form as orthophosphate, ranged from 0.03 to 0.35 mg/L as P. Nitrate concentrations in groundwater samples ranged from less than the detection limit (0.01 mg/L as N) to approximately 24 mg/L as N. Nitrate was not detected in 3 of the 12 sites sampled during the study (2 wells and Elizabeth Lake). Dissolved organic carbon concentrations ranged from 0.4 to 27 mg/L in groundwater and from 9.9 to 100 mg/L in Elizabeth Lake. Ammonium and orthophosphate concentrations generally were low in groundwater. However, elevated concentrations of ammonium in Elizabeth Lake were assumed to be due to avian waste products or biological nitrogen fixation. Groundwater ages were mostly modern (recharged since 1952), with a median recharge temperature of 13 degrees Celsius. Redox conditions in groundwater indicated the likely occurrence of nitrate attenuation by denitrification downgradient from the wells to the south of Elizabeth Lake before groundwater discharges to the lake. Undetectable nitrate in Elizabeth Lake at the time of sampling was likely due to algal uptake. Most wells contained stable isotopes of nitrogen and oxygen in nitrate (δ 15 N-NO 3 and δ 18 O-NO 3 ) molecules with values consistent with denitrification. However, one monitoring well on the north of Elizabeth Lake (ELLA-8) had no evidence of denitrification, based on elevated concentrations of nitrate and a sufficient amount of dissolved oxygen such that the water was oxic and not favorable for the denitrification reaction. Consequently, this nitrate could be delivered to Elizabeth Lake through groundwater discharge if nitrate is not removed from the system by denitrifying bacteria downgradient from the well before the groundwater discharges into Elizabeth Lake. The principal component analysis demonstrated that dissolved organic matter optical properties track different sources of dissolved organic matter from decayed plants, animals, and animal-derived wastes. Two wells contained strong indicators of OWTS water presence, although geochemical evidence indicated other wells may also be affected by OWTS discharge.

California↗

USGS2023

Predevelopment water levels, groundwater recharge, and selected hydrologic properties of aquifer materials, Hinkley and Water Valleys, California

Hydrologic and geophysical data were collected to support updates to an existing groundwater-flow model of Hinkley Valley, California, in the Mojave Desert about 80 miles northeast of Los Angeles, California. These data provide information on predevelopment (pre-1930) water levels, groundwater recharge, and selected hydrologic properties of aquifer materials. A predevelopment groundwater-level map, drawn using water-level measurements from 48 wells collected as early as 1918, showed groundwater movement from recharge areas along the Mojave River to evaporative discharge areas near the margin of Harper (dry) Lake in Water Valley. During predevelopment conditions, depth to water ranged from near land surface along the Mojave River to above land surface near Harper (dry) Lake, consistent with flowing wells in Water Valley at that time. Depths to water in much of Hinkley Valley downgradient from the Lockhart fault were less than 20 feet below land surface. By 2017, water-level declines as a result of agricultural pumping, were as much as 60 feet near the Hinkley compressor station. Areal recharge from infiltration of precipitation on the valley floor is negligible. Average annual recharge as infiltration of runoff from upland drainages to Hinkley and Water Valleys averages 64.7 acre-feet per year. In most years recharge does not occur; in years when it occurs, recharge to Hinkley Valley is typically about 296 acre-feet. In contrast, average recharge as infiltration of streamflow from the Mojave River from 1931 to 2015 was between 13,400 and 17,100 acre-feet per year; in some years recharge from the Mojave River exceeded 100,000 acre-ft. Estimates of predevelopment groundwater movement through Hinkley Gap and groundwater discharge to Harper (dry) Lake ranged from 570 to 1,900 and 820 to 2,460 acre-feet per year, respectively; at the time of this study in 2017, groundwater movement through Hinkley Gap was estimated to be about 83 acre-feet per year. Hydraulic-conductivity values estimated from slug-test data for 95 monitoring wells ranged from less than 0.1 to 680 feet per day (ft/d); values generally decreased with depth. Median hydraulic-conductivity values calculated from nuclear magnetic resonance (NMR) data for Mojave River alluvium and near-shore lake deposits were 73 and 11 ft/d, respectively; median hydraulic-conductivity values for locally derived alluvium and weathered bedrock were 6 and 2 ft/d, respectively. Hydraulic-conductivity values, estimated from NMR data for formerly saturated deposits overlying the 2017 water table, were as high as 300 ft/d near the Hinkley compressor station. Downgradient from the Hinkley compressor station, formerly saturated deposits had hydraulic-conductivity values of about 150 ft/d, which were higher than values in saturated material. Coarse-textured, permeable material in formerly saturated deposits above the 2017 water table may have allowed groundwater, released from the Hinkley compressor station that may have contained Cr(VI), to move rapidly downgradient. The Lockhart fault is an impediment to groundwater flow within Hinkley Valley. Groundwater-flow directions from horizontal point-velocity probe data were deflected to the west on the upgradient side of the fault compared to the nominal direction of groundwater flow estimated from water-level data. Younger groundwater was present on the upgradient and downgradient sides of the fault, and older groundwater with unadjusted carbon-14 ages as old as 5,650 years before present was in water from wells within splays of the Lockhart fault, consistent with limited groundwater movement across the fault. As a result, groundwater and Cr(VI) released from the Hinkley compressor station moved to the northwest along the downgradient side of the fault. Coupled well-bore flow and depth-dependent water-quality data show water from wells C-01 and IW-03 within the Q4 2015 (October–December 2015) regulatory Cr(VI) plume was yielded from thin layers within the aquifer that are composed of well-sorted lake-margin (beach) deposits that likely have high lateral and longitudinal connectivity. Collectively, data show highly permeable deposits above the regional water table and thin permeable deposits within saturated portions of the upper aquifer that may have conducted groundwater and Cr(VI) downgradient when releases from the Hinkley compressor station first occurred.

California↗

USGS2022

Characterization of subsurface conditions and recharge at the irrigated four-plex baseball field, Fort Irwin National Training Center, California, 2018–20

The U.S. Geological Survey performed subsurface and geophysical site characterization of the irrigated four-plex baseball field in the Langford Valley–Irwin Groundwater Subbasin, as part of a research study in cooperation with the U.S. Environmental Protection Agency, the Agricultural Research Service, and the Fort Irwin National Training Center, California. To help meet future demands, the Fort Irwin National Training Center is evaluating the efficacy of gravity-fed drywells to enhance storm-water recharge into the Langford Valley–Irwin Groundwater Subbasin by bypassing fine-grained, less permeable deposits between land surface and the water table. The amount, rate, and location of recharge beneath an irrigated baseball field in the groundwater basin at the Fort Irwin National Training Center is not well understood, so data were collected using physical and geophysical techniques to characterize subsurface materials, geologic controls, and the vertical movement of water through the unsaturated zone to the water table near the drywell at the Fort Irwin National Training Center. Based on the data collected and interpreted from these techniques, several fine-grained deposits were identified. Although these deposits appear to impede the downward movement of water through the unsaturated zone locally, they are not laterally continuous, and water appears to continue to move downward when it reaches the edges of the deposits. These data will help managers evaluate recharge at the site and determine if the use of gravity-fed drywells enhances recharge from surface runoff.

California↗

USGS2021

Evaluation and application of the Purge Analyzer Tool (PAT) to determine in-well flow and purge criteria for sampling monitoring wells at the Stringfellow Superfund site in Jurupa Valley, California, in 2017

The U.S. Geological Survey and U.S. Environmental Protection Agency are developing analytical tools to assess the representativeness of groundwater samples from fractured-rock aquifers. As part of this effort, monitoring wells from the Stringfellow Superfund site in Jurupa Valley in Riverside County, California, approximately 50 miles east of Los Angeles, were field tested to collect information to assist in the evaluation and application of in-well flow as computed by the analytical model called the Purge Analyzer Tool, which computes in-well groundwater travel times for simple piston transport of inflowing groundwater from open intervals of a monitoring well to the pump intake and can provide insight into optimal purging parameters (duration, rate, and pump position) needed for the collection of representative groundwater samples. Field testing of wells included hydraulic, chemistry, and dye tracer analysis to investigate travel times in wells under pumping conditions. The Purge Analyzer Tool was able to replicate dye velocities (travel times) for one of three wells that had appreciable inflow from the aquifer but not the other two wells, which are screened in low-permeability sediments and rock, where flow was dominated by borehole storage. A set of criteria was established to help assess the ability to collect representative groundwater chemistry from monitoring wells; criteria included understanding the height of the static well water column and relative exchange rate between the aquifer and the well.

California↗

USGS2020

Multiple-well monitoring site adjacent to the North and South Belridge Oil Fields, Kern County, California

The U.S. Geological Survey (USGS), in cooperation with the California State Water Resources Control Board, is evaluating several questions about oil and gas development and groundwater resources in California, including (1) the location of groundwater resources; (2) the proximity of oil and gas operations to groundwater and the geologic materials between them; (3) evidence (or no evidence) of fluids from oil and gas sources in groundwater; and (4) the pathways or processes responsible when fluids from oil and gas sources are present in groundwater (U.S. Geological Survey, 2017). As part of this evaluation, the USGS installed a multiple-well monitoring site in the southern San Joaquin Valley groundwater basin adjacent to the North and South Belridge oil fields, about 7 miles southwest of Lost Hills, California. Data collected at the Belridge multiple-well monitoring site (BWSD) provide information about the geology, hydrology, geophysical properties, and geochemistry of the aquifer system, thus enhancing understanding of relations between adjacent groundwater and the North and South Belridge oil fields in an area where there are few groundwater data. This report presents construction information for the BWSD and initial hydrogeologic data collected from the site. A similar site installed to the east of the Lost Hills oil field, 11.5 miles to the north of the BWSD site, was described by Everett and others (2020a).

California↗

USGS2020

Multiple-well monitoring site adjacent to the Lost Hills oil field, Kern County, California

The U.S. Geological Survey (USGS), in cooperation with the California State Water Resources Control Board, is evaluating several questions about oil and gas development and groundwater resources in California, including (1) the location of groundwater resources; (2) the proximity of oil and gas operations and groundwater and the geologic materials between them; (3) the location of evidence (or no evidence) of fluids from oil and gas sources in groundwater; and (4) the pathways or processes responsible when fluids from oil and gas sources are present in groundwater (U.S. Geological Survey, 2019). As part of this evaluation, the USGS installed a multiple-well monitoring site in the southern San Joaquin Valley near Lost Hills, California, adjacent to the Lost Hills oil field. Data collected at the Lost Hills multiple-well monitoring site (LHSP) provide information about the geology, hydrology, geophysics, and geochemistry of the aquifer system, thus enhancing understanding of relations between adjacent groundwater and the Lost Hills oil field in an area where there is little groundwater data. This report presents construction information for the LHSP and initial geohydrologic data collected from the site.

California↗

USGS2014

Construction, water-level, and water-quality data for multiple-well monitoring sites and test wells, Fort Irwin National Training Center, San Bernardino County, California, 2009-12

Because of increasing water demands at the U.S. Army Fort Irwin National Training Center, the U.S. Geological Survey in cooperation with the U.S. Army carried out a study to evaluate the water quality and potential groundwater supply of undeveloped basins within the U.S. Army Fort Irwin National Training Center. In addition, work was performed in the three developed basins—Langford, Bicycle, and Irwin—proximal to or underlying cantonment to provide information in support of water-resources management and to supplement monitoring in these basins. Between 2009 and 2012, the U.S. Geological Survey installed 41 wells to expand collection of water-resource data within the U.S. Army Fort Irwin National Training Center. Thirty-four monitoring wells (2-inch diameter) were constructed at 14 single- or multiple-well monitoring sites and 7 test wells (8-inch diameter) were installed. The majority of the wells were installed in previously undeveloped or minimally developed basins (Cronise, Red Pass, the Central Corridor area, Superior, Goldstone, and Nelson Basins) proximal to cantonment (primary base housing and infrastructure). Data associated with well construction, water-level monitoring, and water-quality sampling are presented in this report.

California↗

USGS2014

Geohydrologic and water-quality data in the vicinity of the Rialto-Colton Fault, San Bernardino, California

The Rialto-Colton Basin is in western San Bernardino County, about 60 miles east of Los Angeles, California. The basin is bounded by faults on the northeast and southwest sides and contains multiple barriers to groundwater flow. The structural geology of the basin leads to complex hydrology. Between 2001 and 2008, in an effort to better understand the complex hydrologic system of the Rialto-Colton Basin, seven multiple-well monitoring sites were constructed. Two to six observation wells were installed in the borehole at each site; a total of 32 observation wells were installed. This report presents geologic, hydrologic, and water-quality data collected from these seven multiple-well monitoring sites. Descriptions of the collected drill cuttings were compiled into lithologic logs for each monitoring site. The lithologic logs are summarized along with the geophysical logs, including gamma-ray, spontaneous potential, resistivity, and electromagnetic induction tool logs. At selected sites, sonic tool logs also were recorded. Periodic water-level measurements are reported, and water-level data are displayed on hydrographs. Water levels at multiple-well monitoring sites in the northern part of the study area differed between the shallow and deep observation wells; in the remaining multiple-well monitoring sites, water levels differed little with depth. Along the southern trace of the Rialto-Colton Fault, water levels are slightly higher east of the fault than west of the fault. Selected water-quality data for 21 of the observation wells show water from wells in the northern and central parts of the study area is calcium-carbonate water. In the southern part of the study area, water from wells screened above 400 feet below land surface is of mixed type or is calcium-carbonate water. Water from wells screened greater than 400 feet below land surface in the southern part of the study area is sodium-carbonate or sodium-mixed anion water. Water from most wells in the study area plots above the Global Meteoric Water Line along an apparent local meteoric water line, indicating the water has not experienced substantial evaporation before infiltration. A few samples from shallow wells in the study area plot slightly to the right of the Global Meteoric Water Line, possibly indicating the water experienced some evaporation before recharge.

California↗